PT-DVBX/PT-DVAX Pentium II/!!! Celeron Twin Processor ATX MAINBOARD ( VER. 2.x ) USER’S MANUAL DOC. NO. UM-DVBX-E2 .................................................................
VIA 693/693A Twin Processor Mainboard TABLE OF CONTENTS TABLE OF CONTENTS Chapter & Section Page 1. INTRODUCTION ...............................................................................1-1 1.1 1.2 1.3 OVERVIEW ............................................................................................. 1-1 MAINBOARD LAYOUT ....................................................................... 1-2 SPECIFICATIONS..................................................................................
VIA 693/693A Twin Processor Mainboard SOMETHING IMPORTANT ! ¶ TRADEMARKS All trademarks used in this manual are the property of their respective owners. ¶ LOAD SETUP DEFAULTS “LOAD SETUP DEFAULTS” is the function which will have the BIOS default settings loaded into the CMOS memory.
VIA 693/693A Twin Processor Mainboard INTRODUCTION 1. INTRODUCTION 1.1 OVERVIEW This Mainboard is a revolutionary high performance personal computer mainboard. It is the ATX form-factor with both Slot 1 and Socket 370 on the board for different package of processors. VIA693 or VIA693A chipset is chosen as the system core logic of the mainboard to give the most outstanding performance and reliability.
INTRODUCTION VIA 693/693A Twin Processor Mainboard 1.2 MAINBOARD LAYOUT JP8 Sound Enable/Disable Short = Sou nd Enabled Open = Sou nd Disabled CN12 IR Port 1. SPK Ou t 2. Line In 3. M ic. In COM 2 COM 1 Parallel Port 4.
VIA 693/693A Twin Processor Mainboard 1.3 INTRODUCTION SPECIFICATIONS ¥ CPU Intel® Pentium™ II, Pentium™ !!! or Celeron™ (f`or both Slot type and Socket type CPU) 233, 266, 300, 333. 350, 366, 400, 433, 450, 466, 500, 550, 600MHz and higher speed processors ¥ CPU VCC Switching Voltage Regulator circuits on board, supports +1.80V DC through +3.5V DC CPU Core Voltage.
VIA 693/693A Twin Processor Mainboard INTRODUCTION ¥ EXPANSION SLOTS AGP Slots : One 32-bit AGP Slot (Supports 1x or 2x AGP graphics cards) PCI Slots : Four 32bit PCI slots. ISA Slots : 16-bit x 1 (One of the slot is PCI/ISA shared) ¥ WOL PORTS One WOL connector supports Wake-On-LAN (WOL up-designed) ¥ USB PORTS Two Universal Serial Bus (USB) ports.
VIA 693/693A Twin Processor Mainboard INTRODUCTION ¥ HARDWARE MONITORING (optional) Winbond W83783S (please refer to U1 on page 1-2) is designed on the board to monitor hardware healthy status like system voltage, system temperature, and cooling fans. When the CPU temperature is too high, the system BIOS will tell the system board to give a series of beeping alarm and slow down the CPU speed (throttling speed) so that you can take proper action to prevent your system from damage.
VIA 693/693A Twin Processor Mainboard INSTALLATION 2. INSTALLATION 2.1 UNPACKING The mainboard contains the following components. Please inspect the following contents and confirm that everything is there in the package. If anything is missing or damaged, call your supplier for instructions before proceeding. l l l l l This mainboard. One USER‘S MANUAL. One Cable set for IDE and Floppy devices. One Pentium™ II Processor Retention Mechanism (RM). One CD diskette for device driver and utility programs.
VIA 693/693A Twin Processor Mainboard INSTALLATION 2.2 AMAZING WAYS TO POWER ON THE PC SYSTEM When the mainboard has been installed successfully, there are several ways to power on the system. Please read the following description for all the details. POWER BUTTON The power button can be programmed by COMS setup program and it has different features. Please refer to page 3-15 for detail function description.
VIA 693/693A Twin Processor Mainboard INSTALLATION ¨ PS/2™ MOUSE (LEFT OR RIGHT MOUSE BUTTON) If you have a PS/2™ mouse connected to the system, you may change the setup in the BIOS and use the mouse click to turn on the PC system power. Please refer to section 4.8 for the BIOS setting To use the mouse key to turn on the PC system power, the mouse click must be done quickly and continually. Basically, 2-5 quick clicks on the mouse key ( left key or right key ) will turn the power immediately.
VIA 693/693A Twin Processor Mainboard INSTALLATION When you have a external modem installed, you can leave the PC system power off. Whenever there is the incoming message, the PC system will be triggered by the ring-in signal and wake up automatically to receive the message for you. From now on, you can tell your PC system to receive the fax message for you.
VIA 693/693A Twin Processor Mainboard INSTALLATION 3. HARDWARE SETUP Before you can start to install this mainboard, some hardware setting is required so that it will work perfectly. To configure the mainboard is a simple task, only a few jumpers, connectors, cables and sockets need to be selected and configured. This section will show all the connectors and jumpers on the mainboard. 3.
VIA 693/693A Twin Processor Mainboard INSTALLATION Setting of JP2: (JP2 is optional) This mainboard has the Hardware Monitoring designed on the mainboard. If you find the W83783S chip installed on U1, then the thermal resistor under the CPU socket will detect the CPU temperature. There are two thermal resistors on the mainboard and the setting of JP2 will decide which resistor is active: Pin 1 & Pin 2 Short: Socket 370 thermal resistor is active Pin 2 & Pin 3 Short: Slot 1 thermal resistor is active. 3.
VIA 693/693A Twin Processor Mainboard INSTALLATION ( Single-Side DIMM module ) ( Double-Side DIMM Module ) 2. Minimum one DIMM module must be installed on the mainboard. 3. For PC133 M/B (VIA693A chipset). please use 3.3V PC-133 DIMM module. 4. For PC100 M/B (VIA693 chipset), please use 3.3V PC-100 DIMM module. 5. You can use single side or double side DIMM module on this mainboard. If your DIMM module does not have the parity bit, please don't enable the Parity/ECC check feature in the BIOS setup. 3.
INSTALLATION VIA 693/693A Twin Processor Mainboard (B) CN1: PS/2 Mouse and Keyboard Connector PS/2 Mouse Connector PS/2 Keyboard Connector 3 2 4 1 A B C + (C) CN3 : Serial Port COM 1 Connector (D) CN4 : Serial Port COM 2 Connector CN4 COM 2 3 2 4 1 CN3 COM 1 CN4 CN3 + (I/O address: 3F8H/2F8H/3E8H/2E8H, IRQ3/IRQ4, selected by CMOS setup.
INSTALLATION VIA 693/693A Twin Processor Mainboard (E) CN5: Parallel Port Connector (Supports SPP/EPP/ECP modes, IRQ7 or IRQ5 is selectable, ECP mode will use either DMA channel 3 or channel 1 which can be selected by the CMOS setup probram) CN5 Parallel Port 3 2 4 1 + (F) CN6: USB Port 1 (Universal Serial Bus) Connector (G) CN7: USB Port 2 (Universal Serial Bus) Connector CN6 USB 1 CN7 USB 2 3 2 4 1 + 3-5 A B C
VIA 693/693A Twin Processor Mainboard INSTALLATION (H) CN8: Floppy Disk Control Port Connector (Use IRQ6, DMA channel 2) 3 2 4 1 + CN8: FDC Connector (I) CN9 : IDE 1 Connectors (Primary IDE Port: 1F0H, IRQ 14) (J) CN10: IDE 2 Connectors (Secondary IDE Port: 170H, IRQ 15) 3 2 4 + CN10: IDE 2 CN9: IDE 1 3-6 1
INSTALLATION VIA 693/693A Twin Processor Mainboard (K) CN12: IR / FIR (Infrared Rays) Connector Consumer IR Connector ( Consumer IR connector is active only when W83977CTF-AW I/O Chip is installed on position U13 ) 3 2 4 1 + IR/FIR (INFRARED RAYS) CONNECTOR CONSUMER IR CONNECTOR ( +5VDC ) 1A 1B ( +5VDC ) ( NO CONNECTION ) 2A 2B ( IR TRANSMIT ) ( IR RECEIVE ) 3A ( GROUND ) 4A ( IR TRANSMIT ) 5A 3B ( CONSUMER IR RECEIVE ) 4B ( GROUND ) CN 12 IR CONNECTOR (Consumer IR is optional) (L) CN13: C
INSTALLATION VIA 693/693A Twin Processor Mainboard (M) CN15: ATX Power Connector 3 2 4 CN4 1 CN3 + CN15 ATX Power connector (N) CN16: WOL (Wake On LAN) Connector In order to use the WOL LAN card to trigger the power of the PC system, the switching power supply must be able to provide at least 700mA current driving ability on the “5V standby” voltage.
INSTALLATION VIA 693/693A Twin Processor Mainboard (O) CN17: Chassis Fan Power Connector 3 2 4 1 + 1 Ground 2 +12V DC 3 Fan Sense Signal 1 2 3 CN 17 (P) CN18: Audio/Game Connector: (Optional) 1. SPK_OUT 2. LINE_IN 3. MIC._IN 4.
INSTALLATION VIA 693/693A Twin Processor Mainboard (Q) CN21 / CN22: CD-IN Connector: (Optional) The CD-IN connectors on the board can be used to connect to the CD ROM audio out. There are two different type of connectors, please check with your CD ROM drive and decide which connector will be used to connect to the CD ROM drive.
VIA 693/693A Twin Processor Mainboard INSTALLATION 1. RS Reset Button Connector Pin1&2 Function Pin # Signal name 1 Reset Control Open No action 2 Ground Short System Reset 2. HL IDE HDD LED Connector Pin # Signal name 1 + 5V DC Pull-up 2 HDD Active Signal 3. SL Sleep LED Connector This LED will be lightened when the AC power is connected and the system is power off, darkened when the AC power is disconnected or the system is powered on. Pin # Signal name 1 Signal Pin 2 Ground 4.
VIA 693/693A Twin Processor Mainboard INSTALLATION b. When the system is in Suspend mode : b-1. Click on this switch ( less than 4 seconds ), the system will return to Full-ON mode. b-2. Press and hold this switch more than 4 seconds, the system will be powered off. R The setup in CMOS is “Instant-off”: A. When system power is off : Click on this switch, the system will be powered on.
VIA 693/693A Twin Processor Mainboard INSTALLATION PWR-LED & KBLOCK: Front Panel Power LED and Key-Lock Connector 1 Pin # Signal name 1 Pullup (+ 5V DC for Power LED) 2 No Connection 3 Ground 4 Keyboard Lock 5 Ground 5 3.4 JUMPERS This section will discuss the jumper setting on the mainboard. In order to let you have better idea of the jumper setting, please see below for the explanation of jumper settings before you start this section.
INSTALLATION VIA 693/693A Twin Processor Mainboard The Keyboard and PS/2 Mouse OnNow function is designed on the mainboard and you can use keyboard and mouse key clicks to power on the PC system. However, there may have some keyboard and mouse are not compatible with the OnNow function. In this case, please use JP1 to disable the OnNow function.
VIA 693/693A Twin Processor Mainboard INSTALLATION Pin 1 & Pin 2 Short: Thermal resistor active on Socket 370. Pin 2 & Pin 3 Short: Thermal resistor active on Slot 1. Note: If you do not make the setting on JP2 properly, the CPU temperature can not be detected when the hardware monitoring feature is installed on the mainboard and your CPU can not be protected. (D) JP8: Onboard Sound interface Enable / Disable (Optional) The ALS300 Sound card interface is optional on the mainboard.
INSTALLATION VIA 693/693A Twin Processor Mainboard (E) JP9: Clear CMOS Data & Keyboard Password Button 3 2 4 1 + 1 1 2 2 3 1 2 3 3 1-2 Short 2-3 Short CMOS Clear Button Normal Setting Clear CMOS CMOS Data Clear Button Note: Improper BIOS setting may cause hang-up to the PC system, Should it be happened, you may use JP9 to clear the information which is stored in the CMOS memory and get the PC system back to normal. Improper connection may cause permanent damage to the mainboard.
INSTALLATION VIA 693/693A Twin Processor Mainboard Note: If you forget the keyboard password which you selected in the BIOS setup program, you may not be able to power on your PC system. (Please refer to Section 4.9 - POWER ON FUNCTION) In case that it happened and you fail to turn on the PC system. you may remove the power cable from your PC system for couple seconds and then you can use the PW button to power on the PC system so that you can modify or remove the password from the CMOS setup.
VIA 693/693A Twin Processor Mainboard INSTALLATION (G) JP12: CPU Voltage Range Selection (Optional) JP12 is a special design on the mainboard. JP12 allows you to select the CPU core voltage range (Vcore) to protect the CPU. The voltage regulator on the mainboard will generate 1.3V ~ 3.5V DC to support different processors. Basically, most mainboards will use the CPU VID signal (VID0~VID4) from the CPU to decide the proper CPU core voltage (Vcore).
VIA 693/693A Twin Processor Mainboard INSTALLATION (H) JP100 / JP133: Over Clock Selection JP100 and JP133 are designed to choose the CPU FSB clock (Front Side Bus Clock). Basically, when you have installed the CPU onto the mainboard, this mainboard will detect the CPU type and specify the proper FSB clock for the CPU. So most of the time you need not to make any setting to select the FSB clock. However, sometimes you may feel like to select different FSB clock for some special purpose.
INSTALLATION VIA 693/693A Twin Processor Mainboard When 693A chipset is installed onboard: FSB CLOCK 66MHz 100MHz 133MHz JP 100 Pin1 - Pin2 Pin3 - Pin4 Open Short Open Open Open Open JP133 Pin1 - Pin2 Pin3 - Pin4 Open Short Open Short Open Open Note: 1. JP100 and JP133 will have no function unless "Default" is selected in the "CPU HOST CLOCK" in the BIOS setup program ( refer to Section. 4-6 ). Please do not to make jumper setting on JP100 and JP133 unless you are the professional technician. 2.
INSTALLATION VIA 693/693A Twin Processor Mainboard CPU (MHz) 233, 350 266, 400 300, 450 333, 500 366, 550 400, 600 433, 650 466, 700 500, 750 533, 800 Clock Ratio 3.5X 4.0X 4.5X 5.0X 5.5X 6.0X 6.5X 7.0X 7.5X 8.0X SW1 OFF ON OFF ON OFF ON OFF ON OFF ON SW2 OFF ON ON OFF OFF ON ON OFF OFF ON SW3 ON OFF OFF OFF OFF ON ON ON ON OFF SW4 ON ON ON ON ON OFF OFF OFF OFF OFF Note: SW setting is inactive when the CPU clock ratio is specified and locked by the CPU .
VIA 693/693A Twin Processor Mainboard INSTALLATION 3.5 INSTALLATION OF DEVICE DRIVERS There is a CD which comes with the mainboard. The CD contains the device drivers which is necessary when installing the mainboard. Please refer to the following procedures to install the device drivers. A. Install the mainboard driver: Before you can use this mainboard in your PC system, you will have to install some device driver so that it will work with Windows properly.
VIA 693/693A Twin Processor Mainboard 4. AWARD BIOS SETUP AWARD BIOS SETUP 4.1 GETTING STARTED When the system is first time powered on or reset by user, the system BIOS will enter the Power On Self Test routines ( POST, which will display a copyright message on the screen and execute a diagnostics and initialization procedure.) In case that there is any error or malfunction detected, the BIOS will give a series of beeping sound or display the error message on screen.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.2 MAIN MENU ROM PCI / ISA BIOS (2A6LGXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP SUPERVISOR PASSWORD BIOS FEATURES SETUP USER PASSWORD CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION POWER MANAGEMENT SETUP SAVE & EXIT SETUP PNP/PCI CONFIGURATION EXIT WITHOUT SAVING INTEGRATED PERIPHERALS LOAD SETUP DEFAULTS ESC : Quit F10 : Save & Exit Setup : Select Item (Shift)F2 : Change Color Time, Date, Hard Disk Type ... Fig.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.4 STANDARD CMOS SETUP ROM PCI / ISA BIOS (2A6LGXXX) STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm : dd : yy) : Mon, Apr 20 1998 Time (hh : mm : ss : 16 : 03 : 33 HARD DISKS Primary Master Primary Slave Secondary Master Secondary Slave TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Auto 0 0 0 0 0 0 Auto None 0 0 0 0 0 0 -----Auto 0 0 0 0 0 0 Auto None 0 0 0 0 0 0 ------ Drive A : 1.44M, 3.5 in.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.5 BIOS FEATURES SETUP ROM PCI / ISA BIOS (2A6LGXXX) BIOS FEATURES SETUP AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP CPU Internal Cache / External Cache : (default setting: Enabled ) These fields allow you to turn on or turn off the Level 1 and Level 2 cache that built-in Pentium™ II/!!! or Celeron™ processors. CPU L2 Cache ECC Checking: (default setting: Enabled ) This option will enable or disable the ECC checking on the CPU L2 cache. The ECC checking will ensure the accuracy of the data stored on the L2 cache.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP Boot Up NumLock Status : ( default setting: Off ) When enabled, the NumLock LED will be lightened after the POST. IDE HDD Block Mode : ( default setting: Enabled ) This field allows you to enable or disable the HDD block mode. Memory Parity / ECC Check : ( default setting: Disabled ) This field allows you to select the Parity / ECC checking feature.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.6 CHIPSET FEATURES SETUP ROM PCI / ISA BIOS (2A6LGXXX) CHIPSET FEATURES SETUP AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP Memory Hole At 15M-16M: (default setting : Disabled ) In order to improve performance, certain space in memory can be reserved for ISA cards. This memory must be mapped into the memory space below 16 MB. Enabled Memory hole supported. Disabled Memory hole not supported. Read Around write (default Setting : Disabled.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP AGP Aperture Size (MB) : (default setting: 64MB ) There is the AGP slot on the board and which allows user to install the AGP display card in the system. The AGP display card will use some of the system memory to store 3D texture mapping data so that the video performance can be increased tremendously. You may use this field to define the memory size which you prefer to use with the AGP card.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP CPU Host/ PCI Clock: (default setting: “Default” ) This selection field is used to decide the CPU FSB clock. Basically, this mainboard is designed by Intel VIA 693/693A AGPset and it supports both the 100MHz and 66MHz FSB frequency. When you select “default” setting, the system BIOS will detect the CPU type and decide the FSB clock automatically. You may also use this field to select different FSB clock and force your CPU to run at higher speed.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.7 POWER MANAGEMENT SETUP ROM PCI / ISA BIOS (2A6LGXXX) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP When the ACPI function is installed in your PC system successfully, you will find the ACPI function in the power management icon. The PW switch (mentioned in Section 3) defined by the ACPI is different to the BIOS setup and it always has the higher priority than what was defined in the system BIOS. According to what was defined by the ACPI in Windows 98, the PW switch can be either the "Standby switch" or "shutdown switch".
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP PM Control APM: (Default setting: "Yes" ) When enabled, an Advanced Power Management device will be activated to enhance the Max. Power Saving mode and stop the CPU internal clock. If the Max. Power Saving is not enabled, this will be preset to No. Video Off After: (Default setting: "Standby" ) When enabled, this feature allows the VGA adapter to operate in a power saving mode.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP HDD Power Down: ( Default setting: Disable ) When enabled and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active.
VIA 693/693A Twin Processor Mainboard 4.8 AWARD BIOS SETUP PNP/PCI CONFIGURATION ROM PCI / ISA BIOS (2A6LGXXX) PNP/PCI CONFIGURATION AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP Manual : The system BIOS will not refer to the ESCD data to assign IRQ & DMA. Instead, it will refer to the information recorded in this field when Assigning the IRQ & DMA resource. ( the system BIOS will always refer to the ESCE data to assign the I/O and memory space resources ). Auto : The system BIOS will refer to the ESCD segment for all legacy information. Reset Configuration Data : Disabled : The system BIOS will do nothing.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP CPU to PCI Write Buffer : (Default Setting : Enabled) When enabled, up to four Dwords of data can be written to the PCI bus without interrupting the CPU. When disabled, a write buffer is not used and the CPU read cycle will not be completed until the PCI bus signals is ready to receive the data. PCI Dynamic Bursting : (Default Setting : Enabled) When Enabled, every write transaction goes to the write buffer.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP It is very simple to tell the difference. If you are going to disable the IRQ on the USB port, check whether is any device connected to the USB port. If you can not find any device, you may feel free to disable the IRQ on the USB port and have the IRQ used by other device. As for VGA adapter, it will be a little difficult. You may try to find whether your VGA card requires the IRQ signal or not.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.9 INTEGRATED PERIPHERALS ROM PCI / ISA BIOS (2A6LGXXX) INTEGRATED PERIPHERALS AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP OnChip IDE Channel0/Channel1 ( Default setting : “Enabled” ) The chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the first and/or second IDE interface. Select Disabled to deactivate an interface, if you install a primary and/or secondary add-in IDE interface. IDE Prefetch Mode ( Default setting : “Enabled” ) The onboard IDE drive interfaces supports IDE prefetching, for faster drive accesses.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP Onboard FDD Controller: ( Default setting : “Enabled” ) This should be enabled if your system has a floppy disk drive (FDD) installed on the system board and you wish to use it. Even when so equipped, if you add a higher performance controller, you will need to disable this feature.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.10 LOAD SETUP DEFAULTS ROM PCI / ISA BIOS (2A6LGXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard 4.11 AWARD BIOS SETUP SUPERVISOR PASSWORD ROM PCI / ISA BIOS (2A6LGXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.12 USER PASSWORD ROM PCI / ISA BIOS (2A6LGXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP SUPERVISOR PASSWORD BIOS FEATURES SETUP USER PASSWORD CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION POWER MANAGEMENT SETUP SAVE & EXIT SETUP PNP/PCI CONFIGURATION EXIT WITHOUT SAVING INTEGRATED PERIPHERALS LOAD SETUP DEFAULT ESC : Quit F10 : Save & Exit Setup : Select Item (Shift)F2 : Change Color Time, Date, Hard Disk Type ...
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP B. When there is no password stored in the "SUPERVISOR PASSWORD" 1. When "Setup" is selected in Security Option: Users can use the "User Password" to log into the BIOS setup program, and they can make all the change in the BIOS setup program. 2. When "System" is selected in Security Option: When turn on the PC system, it will request you to enter the Password.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP 4.13 IDE HDD AUTO DETECTION ROM PCI / ISA BIOS (2A6LGXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC.
VIA 693/693A Twin Processor Mainboard AWARD BIOS SETUP ROM PCI / ISA BIOS (2A6LGXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC. STANDARD CMOS SETUP SUPERVISOR PASSWORD BIOS FEATURES SETUP USER PASSWORD CHIPSET FEATURES SETUP IDE HDD AUTO DETECTION POWER MANAGEMENT SETUP SAVE & EXIT SETUP PNP/PCI CONFIGURATION EXIT WITHOUT SAVING INTEGRATED PERIPHERALS LOAD SETUP DEFAULTS ESC : Quit : Select Item F10 : Save & Exit Setup (Shift)F2 : Change Color Time, Date, Hard Disk Type ...
VIA 693/693A Twin Processor Mainboard 4.15 AWARD BIOS SETUP EXIT WITHOUT SAVING ROM PCI / ISA BIOS (2A6LGXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC.
