Use and Care Manual

180℃（360℉）180S
180℃（360℉）180S
180℃（360℉）90S
180℃（360℉）180S
1、(+)、设置时数值增加。
2、（-）设置时数值减少。
在关机状态下常按-号可以关闭所有的提示音，显示为OFF，
再次常按显示为ON打开提示音。
在开机状态下：同时按+和-号可以进行温度单位华氏度和摄
氏度的转换。出厂默认为华氏度。（在断电后，该操作应该
会保存下来）
3、（SETUP）设置键。按1次开始设置温度，再按1次开始设
置时间，再按1次退出。5秒没有任何动作也可退出。
常按5秒后，进入温度效正设置。（+30度-30度）初始为0
4、(MODE)小人按键为倒计时开始和复位键。
关机状态下：常按MODE小人健5秒，可进入设置自动关机时间，
出厂默认为60分钟。可设置范围为：10分钟至120分钟。
6、最高温度可设为210度，最长时间为999秒。
1.如何开关机/如何开始工作？
2.如何设置温度/时间增加？
3.如何设置温度/时间减少？
4.如何进行温度单位摄氏度和华氏度的转换？
5.如何设置温度/时间？
6.如何设置自动关机时间？
7.温馨提示
P8001
P8001
P8001
210℃ 410℉
220V~ 110V~
50Hz 50-60Hz
1000W
850W
210℃ 410℉
1.基座
2.下盘
3.发热板
4.手柄
5.航空接头
6.按键
7.升降旋钮
8.过载保护器
9.电源插座
10.电源开关
11.立柱
1
2
3
4
5
6
7
8
9
10
11
1
2
3
4
5
6
7
8
9
10
11
The following accessories are equipped according to
the package you choose
200℃(392℉)900S
N
CON1
CON2
H-N L
H-L
P8001
主板和显示屏上面的排线
NTC温度探头
发热盘火线
主进线火线
发热盘零线
主进线零线
N
CON1
CON2
H-N L
H-L
P8001
1.Cables on the motherboard and display
2.NTC temperature probe
3.Hot plate
4.Main incoming line
5.Heating plate zero line
6.Main incoming zero line
2.NTC temperature probe
3.Hot plate
4.Main incoming line
5.Heating plate zero line
6.Main incoming zero line
N
CON1
CON2
H-N L
H-L
P8001
①
②
③④⑤⑥
180℃（360℉）180S
1. How to switch the machine/how to start working?
3. How to set the temperature/time to increase or decrease?
4. How to convert the temperature unit between Celsius and
Fahrenheit?
2. How to set the temperature/time?
5. How to set the automatic shutdown time?
6. How to perform temperature correction?
8. Warm reminder, the highest setting temperature of this machine is
210℃, and the longest time is 999 seconds
7. How to turn on/off the alert tone?
Press the switch button on the side of the temperature control
box to turn it on.
Countdown start button, press once to start the countdown;
press again to reset.
Press once to set the temperature, press again to set the time, press again to exit
(Automatically exit without operation within 5 seconds)
Set time/temperature value increase
Set time/temperature value reduced
In the power-on state, press "+" and "-" at the same
time to switch the temperature unit
Long press for 5 seconds to set the automatic shutdown time.
(The factory default is 60 minutes, the range can be set from 10 minutes to 120 minutes)
Press and hold for 5 seconds to enter the temperature correction setting.
(Range ±30℃, initial value is 0)
In the shutdown state, press "-" to turn off the prompt sound, and the display is OFF;
Press again to turn on the beep and display as ON
This mug heat press machine is matched with 5 in 1and 6 in 1.
This mug heat press machine is matched with 8 in1,9 in 1,10 in 1
and 11 in 1.
1. Pedestal
2. Placement
3. Heating plate
4. Handle
5. Aviation connector
6. Button
7. Lift knob
8. Overload protector
9. Power socket
10. Power switch
11. Column