T-100 User manual
Thank you for purchasing our DONUTMACHINE for your home or business! With this high quality and easy to use appliance, you can enjoy your cookout with your families and friends or earn more profits for your business. *Please read the instructions carefully before using it. Catalog I . Specification………………………………...............1 II. Important safeguard………………………….….1 III. Operating instruction…………………………...2 IV. Cleaning & Storing………………………….…...6 V. Illustration …………………...…………………...7 VI.
I. SPESIFICATIONS Voltage AC220V/60Hz Heating Power 6000W Yield 300-1200 pcs/hour Donut Diameter 3~10 CM Machine’s Size 114cm*55cm*69cm II. IMPORTANT SAFEGUARDS A. Make sure that your power supply matches with the power that marked on the product. The deviation is under 10%. B. Before connect the power, please connect the ground wire firstly. C. Before obtaining access to terminals. All supply circuits must be disconnected. D.
！Over-wet food and too large a charge shall also be drawn to the effect on surge boiling. L． The instruction concerning persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge is not applicable. III. OPERATING INSTRUCTIONS *To run the machine, take a few seconds to know about all switches. Refer to these switches on machine’s plate. K1: To lock and hold plunger tightly.
! It is recommended within180 ℃ ,180 ℃ is the best donut fry temperature. When Temperature is over 200 ℃ ,to protect the equipment,the power of the machine will be cut aromatically.When machine is below 200℃,you can restart it by press RESET switch in the back. S4: Control number of donut(one or two) dropping from Funnel at a time. The switch only works while the S6 works normally. S5: It is a the conveying switch . S7: Power switch,which supply the electric to the whole machine.
There are 3 degree, 1 is the least and 3 is the biggest. * Change donut’s size, and then go through the following steps. 1. Choose the size you want to make(3~5cm,5~7cm &7~10cm) 2. Matching the mold with Funnel’s bottom, then screw it tightly. 3. Screw the plunger with the matched mold. 4. Finally, put the plunger into the funnel and adjust it up and down.
********************************************************** And follow these steps to operate the machine! 1. Install all parts of the machine 2. Connect power. Make sure that the power requirements of the machine do match the power source as specified on the data plate. 3. Pull oil into fryer tank. ！Notice the mark in the oil tank, 25L oil is recommended. DO NOT have it over 26 L nor lower 10L. ! Danger of fire exists if the oil’s level is below the minimum indicated level.
Funnel. If so, press S2 to make dough drop automatically. IV. CLEANING & STORING 1. DO cut off the appliance’s power supply and wait it cooling down before cleaning. 2. Do not use strong alkali cleaners such as lye, soda ash, or trisodium phosphate, these will discolor or even corrode the equipment. Wipe the appliance with soft cloth .Never with abrasive products. 3. Store it in a dry place away from corrosive substances. 4. Cleaning the hopper and the plunger: 1. Unplug the cutter head power cord. 2.
V. size. And have the oil poured from tank vie the handle under the left of the oil tank . After all of these you can clean the tank easily. 6. Dry each part completely. 7. Dip the plunger and the funnel cylinder in mineral oil or liquid shortening to prevent rust and sticking. 8. Wipe the cutter head assembly with a soft cloth dampened with hot water and an appropriate cleaner. Wipe it with another damp cloth to remove the cleaner. Wipe it dry. ILLUSTRATIONS VI. Package Includes: A. 1x Electricity box B.
VII.Assemble The machine Step 1: Unpack all the parts,. (See VI. Package Includes) Step 2: Insert transmission bar into Fryer’s left hold. Then connect transmission bar with cutter head, screw them tightly ( see illustrations point D and C) Step 3: Put Plunger into Funnel, and then screw the Funnel. And fix the plunger. Step 4: Fix the transmission bar with the Fix bar. Then plug the cutter head’s wire with the machine.
