80° TUBE BENDER USER MANUAL We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us.
Model: CT-612 NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us: CustomerService@vevor.com This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
Product Overview The VEVOR 180° TUBE BENDER is used to Bend 1/4" , 3/8" and 1/2" tubing. For bending soft copper, aluminum, brass, thin wall steel, thin wall stainless steel and other tubing. Makes smooth, tight-radius 180° bends. Calibrated markings-for making accurate left-hand, right-hand and offset bends. Adjustable hook for optimum bending radius. Patented Technical Specifications Pipe outer dia: 1/4" 、 3/8" 、1/2 " Wall thickness of pipe: ≤1.2mm Bender angle: 0°— 180° Bender dia: 5/8" Gross Weight: 1.
WORK AREA 1.Operate in a safe work environment. Keep your work area clean, well-lit and free of distractions. 2. Keep anyone not wearing the appropriate safety equipment away from the work area. 3. Store unused tools properly in a safe and dry location to prevent rust or damage. Lock tools away and keep out of the reach of children. PERSONAL SAFE TY WARNING! Always Wear personal protective equipment. Broken materials may fly. PERSONA L PROTECTIVE EQUIPMENT 1.
SPECIFIC SAFETY PRECAUTIONS 1. Use the correct tool for the job. This tool was designed for a specific function. Do not modify or alter this tool or use it for an unintended purpose. 2. Keep bender bearings and form handle grooves lubricated.Keep oil away from wheel grooves. Keep body parts away from pinch/bend areas while using. Ensure tubing is secure in tool before bending. 3. Children are not allowed to operate this product unless accompanied by an adult. 4.
Lower the form lever until the “0"on the form lever and form wheel are aligned(Fig.3).Pull the form lever down until the desired bend angle is obtained. Degree of bend is indicated when the “O”mark on the form lever aligns with the desired degree graduation on the form whee l(Fig.5A).
Making Accurate 90° Center line Bends 90°BENDS FOR 1/4" TUBING Determine the desired Center line dimension (Dimension “L” in Fig.4). Measure from end of the tube at “L” distance and place a mark on the tube (Mark “L”). Position tube in bender as shown in Fig.5. If the end measured is left of the tube-clamping hook the measured mark “L” should be directly under the “L” graduation on the form lever face plate as shown in Fig.5.
90° Bends for 3/8"& 1/2" Tubing Place mark."L"on the tube in the same manner as required for the 1/4”size. For a bend to the left of the tube-clamping hook refer to Table 1. Subtract from the original mark "L" the appropriate length, and place a second mark "B"on the tube.This second mark "B" should be placed on the right edge of the tube-clamping hook as shown in Fig.7. For bends to the right of the tube clamping hook, place mark “R” on the tube in the same manner as required for the 1/4^ size.
Lower the form lever until the “0” mark on the form lever and form wheel are aligned, then pull the form lever down until the desired bend angle is obtained. Degree of bend is indicated when the “0” mark on the form lever aligns with the desired degree graduation on the form wheel(Fig.5A). As an alternative to the calculation table for making right or left bends, a scale on the form lever handle is provided.
Making bends right of tube clamp hook Table 2.This is for "R" Dimension and must be added to the center line requirement. Tube Mark“B” Diameter Fractions(Decimal) 3/8" 2-1/16"(2.062") 1/2" 2-17/64"(2.265") Length Correction Factor for 90° Bends To arrive at the exact tube length to fabricate a circuit, the following method may be used. Add all center-to-center dimensions of tube circuit . For each 90° bend, subtract the amount shown in chart “A”. Circuits are dimensions to square corners.
UK REP EUREP UK LTD UNIT 2264, 100 OCK STREET, ABINGDON OXFORDSHIRE ENGLAND OX14 5DH EC EUREP GmbH Unterlettenweg 1a, 85051 Ingolstadt, Germany REP Importer: WAITCHX Address: 250 bis boulevard Saint-Germain 75007 Paris Importer: FREE MOOD LTD Address: 2 Holywell Lane, London, England, EC2A 3ET Manufacturer：Wujiang Dunnex Tools Co., Ltd Address：No.
Technical Support and E-Warranty Certificate www.vevor.
