Technical Support and E-Warranty Certificate www.vevor.com/support LABELING MACHINE USER MANUAL We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
LABELING MACHINE MODEL:SY-60-V1 NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us: Technical Support and E-Warranty Certificate www.vevor.com/support This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received.
1. Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. 2. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. GENERAL SAFETY RULES Important reminder 1.Before use, please carefully read the product manual and ensure that you understand and comply with all safety warnings and usage precautions. 2. Do not use this product for other non-designated purposes to avoid unexpected risks. 3.
mismatched devices to avoid risks such as electric shock and fire. 3. When foreign objects are found on the surface of the product, please immediately stop using and remove the foreign objects before continuing to use. 4. When using this product continuously for a long time, please rest in good time to avoid excessive fatigue. Maintenance and upkeep 1. Regularly maintain and clean the product. Before cleaning, please disconnect the power supply and wipe it with a dry cloth.
MODEL AND PARAMETERS Model SY-60-V1 Applicable Item Size 120*150*(25-90)mm L*W*H Label Width 30-100mm Label Length 30-60mm Label Roll I.D ＞76mm Label Roll O.D ＜300mm Air Supply Pressure 0.4-0.8MPa Vacuum Supply -5Pa Input to -20Pa AC 120V Power(Max.
STRUCTURE DIAGRAM 10 9 1 3 7 4 2 8 6 5 11 1.Label Baffle 2.Sensor 3.Power Switch 4.Oil-water Separator 5.Scroll and Paper Clip 6.Adjustable Roller 7.Suction Cup 8.Horizontal adjustment hand-wheel 9.Vertical adjustment hand-wheel 10.Label Holder 11.
COMPONENTS Model SY-60-V1 Parts Label Baffle ×2 Label Holder A ×1 Label Holder B ×1 Power Cord ×1 Pedal Switch ×1 Positioning Frame ×2 Hex Wrench(#6、#5、#4、 #3) ×4 Screw(M4×8) ×4 Oil-water Separator (AFC-2000) ×1 User Manual ×1 -6-
OPERATING INSTRUCTIONS 1.Assemble two baffles and label holders(A,B) and fasten with screws（M4*8). A B 2. Insert the A , B and label roll in turn as shown. Note:The label holder is secured by tightening the bolt on it. B A 3.Place the green O tape over the label holder A Note:The label holder A has a belt groove.
4.Pull the label across C,D, then around E and down, and then across between F and G.Finally Wrap the label backing paper tightly around the scroll(H) and attach the paper clip as shown. Note:a) The installed labels should be aligned smoothly from the fixed axis to the scroll.(from beginning to end) Otherwise, the label will be easily torn. b) It is recommended that the label be wrapped around the scroll at least 2 to 3 times.
F G H Label Paper Route -9-
5.Remove the screws,install the positioning frames(J) and lock them with the removed screws as shown. J 6.Remove the screws,install the oil-water separator and lock it with the removed screws as shown. 7.
8.Connect the air source to the air intake K and the vacuum air source to the L as shown.（The vacuum equipment should be provided by the user） Note:The recommended air source pressure is 0.4-0.8MPa. Vacuum pressure is -5to -20Pa. L K 9.Insert the power cord and 10.Product assembly completed. pedal switch as shown.
The operating instructions 1.Suction cup position setting The height position of the suction cup can be adjusted by N. The horizontal position of the sucker assembly can be adjusted by M. The following conditions must be met when adjusting the position of the suction cup(O) as shown : X=1-3mm，Y=1-3mm.
2.Turn it on and try labeling it.,Observe the extension length of the label . Adjusting the sensor position can control the extension length of the label. It is recommended that the extension length of the label be 0-1mm. D Label 3. Adjusting the throttle valve(P) can change the lifting speed of the suction cup as shown. Adjusting P1 can change the speed of the suction cup descent. Adjusting P2 can change the rising speed of the suction cup.
4. Blowpipe Angle setting Loosen the screw and turn the blowpipe so that the air outlets slope up 40 to 50°,Then lock the screw. Note:There is a row of small air outlets in the blowpipe. Blowpipe Screw 5.The work table is provided with positioning frames in two directions. Put the flat objects on the worktable and adjust the position of the positioning frame according to the need for labeling as shown. 6.
MAINTENANCE 1. Inspect periodically all parts and accessories and replace them if damaged. 2. Have damaged parts replaced by an authorized service center. 3. Check the nuts periodically and tighten them if they are loose. 4.Please use a soft, clean cloth when cleaning the machine.Do not flush the machine with water or liquid. 5.Please store the product in a dry and ventilated place.
TROUBLESHOOTING Problem Possible Cause The suction cup did not Air rise insufficient. The pressure position suction The suction cup fails to absorb the label. Possible Solution cup is Provide adequate air supply. of the is set improperly. Readjust the position of the suction cup. The reserved label is too Shorten the reserved long label length. The angle of the blow Adjust the Angle of the pipe is unreasonable blow pipe.
Address：Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd.
Technical Support and E-Warranty Certificate www.vevor.
