ICE CREAM MACHINE OPERATING INSTRUCTION Please Read the Instructions Carefully Before Operating the Machine 1
CONTENTS Safety Caution·········································3 Installation and Test Run ··································5 Operating Instruction ·····································7 Cleaning and Maintenance··································9 Trouble shooting and Solution······························10 Content with this sign are Content with this flag is Content with this flag is a acts that must be prohibited; related to product safety or matter of consumer must pay otherwise it may resu
>SAFETY CAUTION< To prevent the water and other conductive liquids flow into the machine; When there is no mix or water in the freezing cylinder, the machine is not allowed to work, failure to follow this instruction may damage the beater. When the machine is working, no stick or something like that put into the air grid or the dispenser door spout. Carrying or moving the machine, the maximum tilt angle is 45°.
maintenance department. When remove the assembly unit or clean the machine, please cut off the power after stopping the use of machine, For the machine without plug, the power wire must be connected with the external power with air switch, and the power wire should be connected with the air switch directly.
1. Unpack the case, move the machine to a suitable place. Count the accessories according to the packing list. Description of the least space for installation Attention: Enough space must be guaranteed to make sure operator can work well; 2.
Attention: 1, Make sure the ground line is perfectly connected; 2, All outside wires and electrical appliance meet the relative national standard; 3, For the machine without plug, the power line can only be directly connected to the air switch; If rated power less then 2000W, please use air switch with 10A (single phase power) or 10A (three phase power); If rated power greater than 2000W, please use air switch with 32A (single phase power) or 16A (three phase power). B. Run Test 1.
6. Use the clean water to repeat the above steps 2-3 times. 1. The temperature of the solutions should be less than 60℃, or it will damage the parts. 2. After the cleaning, please make sure no any water in the cylinder, or the frozen ice will damage the auger when the machine is freezing. >OPERATING INSTRUCTION< A. Front Panel Ⅰ. Instructions for setting 1.
N 1 2 3 4 5 6 Meaning Hopper pre-cooling temperature Frozen cylinder keep fresh Hopper pre-cooling temperature Compressor restart period setting Compressor restart period setting Beater motor shutdown delay Prom P0 P1 P2 P3 P4 P5 Scope of 1--19℃ 1--10℃ 1--10℃ 2-15min 1--15min 1-- Default 4℃ 4℃ 2℃ 15min 5min 30secon P1 is not suggested to adjust. Ⅱ.Instruction for function 2.
-”, and the machine will buzz and stop working at the same time. 2. The rotating speed of drive motor is too slow, the screen will show “NL”, and the machine will buzz and stop working at the same time. 3.If the limit switch behind the dispenser door is connected to the power for over 1 minute, the screen will show “Cb”, and the machine will buzz and stop working at the same time. 4. If the mix in hopper is not low, the screen will show“QL” B. Making Ice Cream 1. Rinsing before making the ice cream 1.
2. Preparation of Mix Follow the instruction to make the mix with ice cream powder, avoid ice cream particles or impurities inside. Fill into the container after 5 minutes’ standing, or you can use liquid ice cream mixture directly. If a fridge is available , the mix can be pre-stored in it to 4 ℃ for better ice cream producing. 3. Adding mix to the hopper 3.1 Pour half of the prepared mix into the hopper. 3.
>CLEANING AND MAINTENANCE< There is no set period and procedures of the maintenance. It depends on the using and working condition, so each ice cream machine needs A. Cleaning 1. Cleaning of hopper and cylinder 1.1 Press “WASH” button and draw off all the residual mix in the hopper and cylinder, then press “WASH” button again to stop. 1.2 Prepare 3 liters of solution using sanitizer in a bucket of cold water, pour the solution into the hopper. 1.
while assembling the piston, O-ring and gasket. 1. Before installing the piston, O-ring for piston, beater and gasket for auger, you should lubricate Vaseline (lubricating Vaseline onto the groove of the gasket, do not onto the auger’s end ), using the Vaseline 2. Cleaning of the exterior of machine Keep the exterior of machine clean, use wet towel to clean it, and do not flush the machine with water directly. 3.
internal parts. Be familiar with all the operational modes of your machine and what they do. Understand the different features of each mode for safe and reliable operation. Use a recommended soft serve machine cleaner and sanitizer when cleaning your unit. Regular dish soap, chemicals, and detergents can degrade seals and leave unwanted residues in your machine. Do not run the machine with water in Auto Mode.
>TROUBLE SHOOTING AND SOLUTION< Some problems may happen to the machine, the corresponding solutions have been listed on the following trouble shooting sheet for your reference, if the problem persists, please don’t handle it by yourself and contact our professional technicians for help, in order to avoid unnecessary loss. PROBLEM PROBABLE CAUSES SOLUTIONS Machine is not plugged in. Check it and plug it properly. Machine does The general switch is not on. Turn the general switch on.
working. Find the leaking point and fix it, charge Refrigerant leaking. the refrigerant after vacuuming the refrigeration system. Machine does not freeze Solenoid valve is not working. The fan motor does not work. Fix the fan motor or replace it. The compressor is out of order. Check the compressor, replace it if necessary. The hardness is set too high. Reduce the hardness setting. Machine does not There is something wrong stop with control board. Check the refrigeration system.
leaking. if it is necessary. The dispenser door is Check the O-ring for dispenser door, Mix leaking leaking. replace it if it is necessary. The drain pipe is leaking. Low voltage protection. The buzzer keep squealing Check the gasket for the auger, replace it if it is necessary. Turn off the machine first, then turn on the machine 5 minutes later. Turn off the machine first, then turn on Shutdown protection. the machine 5 minutes later.
