Instruction Manual

060217.02 7
Remote control WRC
ENGLISH
5 Battery insertion/replacement
From the backside remove both stainless steel clamps and remove
the rear part of the housing. Remove the electronic circuit from the
housing and replace the battery. Battery type: CR2032. Reassemble
it in reverse order.
6 Program (additional) transmitter
Each new transmitter must be added. A maximum of 5 transmitters
can be coup led to one receiver. If a 6
th
transmitter is added the 1
st
transmitter will be deleted from the memory of the receiver.
Make sure that the wiring of the receiver is connected and the power
supply switched on.
1. Press and hold the ‘ON’ key for about 2 seconds to switch on the
new station.
2. Press and hold the ‘PROG.’ key until the red led lights up (4 sec.).
3. On the new transmitter, press one of the keys and keep it pressed
until the red led in the receiver ashes.
The transmitter is now logged on. Wait for the red led to switch o
before using the new transmitter.
7 CAN Control
CAN control is only available for Vetus V-CAN control led thrusters.
BOWPRO thruster connection must be done through CAN-bus in-
stead of relays.
The receiver decodes the signals which are broadcasted into the V-
CAN line and detects the status of the thrusters and the requests of
the connected panels. For starting or recovering the control from the
transmitter, the user must push the ‘ON’ button. The green led will
turn on to indicate that the device is ready for usage.
7.1 led indications receiver
Green and red leds are blinking: Communication lost with any CAN
control led thruster. If the communication with the other CAN control
led thruster remains, it can still be used.
Once the communication with thruster is reestablished, errors can be
removed by pressing the ‘ON’ button on the remote control.
GREEN double blink: Control taken by another control panel.
Push ‘ON’ to recover the control.
Yellow led 1 blinking Bow thruster overheat
Yellow led 2 blinking Bow thruster low voltage
Yellow leds 1 and 2 blinking Bow thruster overload
Yellow led 3 blinking Stern thruster overheat
Yellow led 4 blinking Stern thruster low voltage
Yellow leds 3 and 4 blinking Stern thruster overload
8 Thrust direction
By changing the system conguration, the bow/stern thruster's
thrust direction can be reversed.
led 1 ashes standard bow thruster thrust direction
led 2 ashes reverse bow thruster thrust direction
• To reverse the thrust direction of the bow thruster, briey press
the 'PROG' key.
Wait for 10 seconds to exit setup mode, or
• Press and hold the 'PROG' button (4 sec.) until the yellow led 3 or
led 4 starts blinking.
You are now in the stern thruster, thrust direction setup mode.
Press and hold the PROG button until the
red led lights up (4 sec.).
Press and hold the PROG button until the
yellow led 1 or led 2 starts blinking.
You are now in the bow thruster, thrust
direction setup mode.
4 sec.
2. 3.1.
15 sec.
2 sec.
PROG.
PROG.
led 3 ashes standard stern thruster thrust direction
led 4 ashes reverse stern thruster thrust direction
• To reverse the thrust direction of the stern thruster, briey press
the 'PROG' key.
Wait for 10 seconds or press and hold the 'PROG' button (4 sec.) to
exit setup mode.
9 Technical specications
Remote control
Power supply 3 VDC CR2032 (1x)
Protection class IP66
Frequency 433.92 Hz
Temperature range 0°C - 70°C (+32°F - 158°F)
Weight 50 g (2 oz)
Receiver
Power supply 8 VDC to 30 VDC
Maximum current (per output) 8 A (at 30 Volts DC)
Protection class IP40
Frequency 433.92 Hz
Temperature range 0°C - 70°C (+32°F - 158°F)
Weight 800 g (28 oz)