Product Manual

instructions
and
wa rnlngs
first
before
attem
pting
to operate
this
Read allthe
lifting crane
1.
lO00LBLimit.Do
noloperate
lhe
hydraulic
pump
beyond
rated capacity.
Do not
exceed winch
load weig ht
caPaciiY.
2. Avoid
any moving
parts
while
using
this lifting
crane,
keep fingers
and hands
away from
moving
parls
3.
Be certain
the crane is
properly
bolted
to a
truck bed
lhat can
hold the
load'
4.
Never come between
the crane
and
the load
when operating
5'NeVerfu||yeXtendcabIeWhiIepuIlingaIoad.Keep4compIeteturnsofcabIearoUndthewinchmoduIe,
6.
Neveroperate
winch
if cable shows
any signs
of
weakening
is knotted
or kinked
7.
Never fully extend
the cable
which
under load.
B. Don't
overreach.
Keep
proper
footing
and balance
at all
times
9. Never
lifi
peoplo
of
hoist loads
over
people.
l0.Alwayssetparkingbrake
andblock
tireswhen
usingthis
trucklifl.vehicles
with a utomatic tran smissions
should be
left in
"park,'
Manual
transmissiors
should
be left
in
gear.
Never alternpt
to lift
something
while the
vehicle
is moving.
11. Stav Alert.
Watch
what
you
are
doing Usecomrnonsense
Do not operate
any
toolwhef
you
are
tired'
1.PIacetheBase(#P)inthelocationonthetruckbedWhe|eitistobesecured.Thisf|atIocalionmustbeabIe
to suoport
tho lift
with a
1000 lbs
load.
(on
most
lrucks,
a desirable
position
is
just
behind
the wheel so
that
the boom may
be stored
over the
wheel well.)
lJsing a
pencil,
mafk
through ihe
mounting
holes in
the Lift Base
{#P)
to mark
driLl holes
Using
a
power
drill and appropriate
drill bit
size, drill
holes through
truck
bed
Secure
ihe base onto
the truck
bed holes
using bolt,
nut,
lock washer
and
flal washer
(not
included'
use
correct
size
boli, nut,
washers as
per
the
thickness of
your
truck bed)
AitachtheWheel
Hub(#O)
to
Turntable(#N)
PlaceTurntable(#N)ontotheBase(#P)andsecureilwith
Wheel
Binding Bolt
(#Q).
2.
3.
4.
5.
6.
Place tho
Main Post
(#H)
onio
Turntable
(#N)
and
secufe it
with Bolt
(#17), Nut
i#4)'
Flat Washer
(#2)
and
LockWasher
(#3).
7. Attach
Boom
(#E)
and Large
Pulley
(#F)
to
Main Post
(#H)
using
Bolt
{#9),
Nnl
(#8),
Lock
Washef
(#7)
and
Flat
Washef
(#6)
through
the holes
on the
bracket of
main
post
and boom'
B. Attach
the bottom
of Pump
Unit
(#1)
to Main
Post
(#H)
using
Bolt
(#13),
Nut
(#12)'
Lock
Washer
(#
11) and
Flat Washer
(#10).
L Connect
ihe
Pump Unit
plunger
to the
Boom bracket
using
Bolt
(#14),
Nut
(#12)'
Lock
Washer
(#11)and Flat
Washer(#10).
1
0. slide the
Extension
Boom
(#D)
into the
Boom and
secure
iiwithBolt(#5),
Nut(#8),
Lockwasher
(#7)and
Flat
Washe(#6).
11.
Aitach Winch
(#J)
to
Main Post
(#H)
using
Bolt
(#20).
12. Attach
Winch
Handle
(#K)
to Winch
using
Bolt
(#15) and Flat
Washer
(#16)
13. Assemble
the Small
Pulley
(#B)to
the
front of
Boom Exiension
(#D)
using
Bolt
(#1
)'
NLlt
(#27)'
Lock
Washer
(#26)
and Flat
Washer
(#25)
14. Pull
ihe cable
of winch
out from
Boom and
Extension
ihrough
the notch
of large
and small
pulleys.
15. Attach
the hook
(#A)
to
cable and
lock it wiih
Two Buckles(#23)