INDUCTION HOB INSTALLATION AND OPERATING INSTRUCTIONS
CONTENTS: Safety instructions.............................................................................................3 Description of the appliance.............................................................................5 Cooking surface and control panel of heaters......................................................5 Operation of the appliance................................................................................7 Switching the appliance on and off......................................
PART 2 SAFETY WARNINGS READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE USING YOUR APPLIANCE, AND KEEP IT IN A CONVENIENT PLACE FOR REFERENCE WHEN NECESSARY. THIS MANUAL IS PREPARED FOR MORE THAN ONE MODEL IN COMMON. YOUR APPLIANCE MAY NOT HAVE SOME OF THE FEATURES THAT ARE EXPLAINED IN THIS MANUAL. PAY ATTENTION TO THE EXPRESSIONS THAT HAVE FIGURES, WHILE YOU ARE READING THE OPERATING MANUAL.
- WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock. - For induction hobs, metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot. - For induction hobs, after use, switch off the hob element by its control and do not rely on the pan detector. - For hobs incorporating a lid, any spillage should be removed from the lid before opening.
- Your appliance is produced in accordance with all applicable local and international standards and regulations. - Maintenance and repair work must be made only by authorized service technicians. Installation and repair work that is carried out by unauthorized technicians may endanger you. It is dangerous to alter or modify the specifications of the appliance in any way.
DESCRIPTION OF THE APPLIANCE Dear Customer, Please read the instructions in this user guide before using the hob and keep it for future reference.
Control Panel for 4 heater : Timer Display Upper left Increase heater selection heat setting/ timer(optional) Heater Display Upper Right heater selection Key Key Lock Lock Indicator Smart Pause Decrease lower left Lower Right heat setting heater selection heater selection / timer(optional) Timer Control Panel for 3 heater : Boost On/Off Timer Display Upper left Increase heater selection heat setting/ timer(optional) Heater Display Key Key Lock Lock Indicator Smart Pause Decrease lower left Lower Ri
OPERATION OF THE APPLIANCE Use the induction cooking zones with suitable cookware. After mains voltage is applied, all displays are come on for a moment. When this time is over, the hob is in the stand-by mode and it is ready for operation. The hob is controlled with electronic sensors which are operated by touching the related sensors. Each sensor activation is followed by a sound signal (buzzer). Switching the appliance on: Switch the hob on by touching ON/OFF key .
Switching all cooking-zones off: To turn all the cooking zones off at once, touch the key. In the stand-by mode, an "H" appears on all cooking zones which are hot. Residual heat indicator: Residual heat indicator indicates that the glass ceramic has a dangerous touch temperature in the circumference of a cooking zone. After switching off the cooking zone, the respective display shows "H" until the assigned cooking zone temperature is in an uncritical level.
Safety switch off function: Every cooking zone will be switched off after a defined maximum operation time if the heat setting is not modified. Every change in the cooking zone puts back the maximum operation time to the initial value of the operating time limitation. The maximum operation time depends on the selected temperature level.
Timer function (*optional): The timer function is realized in two versions: Minute minder timer (1..99 min): The minute minder timer can be operated if the cooking zones are switched off. The timer display shows "00" with a blinking dot. Touch to increase the time or touch to decrease the time. Adjustment range is between 0 and 99 minutes. If there is no operation in 10 seconds, the minute minder timer will be set and the blinking dot will disappear.
When the timer has run down, a signal sounds and the timer display shows "00" statically, the assigned cooking zone timer LED blinks. The programmed cooking zone will be switched off and the "H" will be displayed if the cooking zone is hot. The sound signal and the blinking of the timer LED will be stopped automatically after 2 minutes and/or by operating any key.
HINTS AND TIPS Cookware · Use thick, flat, smooth bottomed cookwares that are the same diameter as the element. This will help reduce cooking times. · Cookware made of steel, enamelled steel, cast iron and stainless steel (if appropriately abelled by the manufacturer) will give you the best results. · Cookware made of enamelled steel or aluminium or copper bottoms can cause a metallic residue to remain on the hob. If left, this becomes difficult to remove. Clean the hob after every use.
Examples of cooking applications The information given in the following table is for guidance only. Settings 0 1-3 4-5 6 -7 8 9 P Use for Element off Delicate warming Gentle simmering, slow warming Reheating and rapid simmering Boiling, saute and searing Maximum heat Boost function Cleaning tips · Do not use abrasive pads, corrosive cleaners, aerosol cleaners or sharp objects to clean the surfaces of the hob. · To remove burnt food, soak it off with a damp cloth and washing-up liquid.
INSTALLATION OF THE APPLIANCE WARNING: The electrical connection of this hob should be carried out by a qualified electrician, according to the instructions in this guide and in compliance with the current regulations. In the event of any damage that occurs as a result of improper connection or installation, the warranty will not be valid. This appliance must be earthed. Installation safety · Any overhanging surface should be at least 65cm above the hob.
Screw the 4 worktop mounting brackets on the side walls of product. worktop mounting bracket · Secure the hob in place by putting it into cutout on the work surface. · Before inserting the oven, it is necessary to remove the rear kitchen element panel in the area of the oven opening, in order to supply cooling. Equally, the front part of the kitchen element must have an opening of no less than 5 mm. Min. 35 mm Min. 10 mm Min. 10 mm 14 Min.
Making an electrical connection Before making a connection, check that: · The mains voltage is the same as that quoted on the rating plate which is situated at the back of your hob. · The circuit can support the appliance load (see the rating plate). · The power supply has an earth connection, which complies with the provisions of current regulations and is in good working order. · The fused switch is easily accessible once the hob has been installed.
Electrical connection diagram 3x2,5 mm² 220V~ 3x2,5 mm² 230V~ 3x2,5 mm² 240V~ 5x1,5 mm² 380V 3N~ 5x1,5 mm² 400V 3N~ 5x1,5 mm² 415V 3N~ * This appliance must be earthed. * For this connetion a power lead of wire type H05V V -F should be used. For the induction hob, the cable must be H05VV-F 3X2,5 mm²/60227 IEC 53 ••. You will find the connection diagram shown on the bottom of your appliance.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
