Specifications

ManualsBrandsVestax ManualsMusical equipmentPDX-2000MkII, PDX-2000MkII

Vestax Mixing Controller

SEP.2004 VMC180E○

Vestax Corporation

SPECIFICATIONS

INPUT

SECTION

ISOLATOR

SECTION

MIC MAIN/SUB（1/4' PHONE JACK） -50.0dBv -32.0dBv 3.3kΩ

PHONO 1∼3L/R （RCA JACK） -46.0dBv -22.4dB v 47kΩ

LINE 1∼5L/R （RCA JACK） -10.0dBv +11.6dBv 47kΩ

HI 10KHz -

∞

∼ +4dB

MID 1KHz -

∞

∼ +4dB

LOW 80Hz -

∞

∼ +4dB

RATED OUTPUT

MAXIMUM OUTPUT

IMPEDANCE

MASTER OUT L

／

（XLR JACK BALANCED）

0dBv +11.4dBv 10kΩ OVER

SUB MASTER OUT L

／

（1/4' PHONE JACK UNBALANCED）

0dBv +11.4dBv 10kΩ OVER

MASTER2 L

／

R（RCA PIN JACK UNBALANCED）

0dBv +11.4dBv 10kΩ OVER

SEND OUT L

／

（RCA PIN JACK UNBALANCED）

-10dBv +11.4dBv 10kΩ OVER

HEAD PHONE（1/4' PHONE JACK） (47Ω LOAD 130mW) 8∼600Ω

MIC 30Hz ∼ 20kHz ±3dB CROSSFADER CROSSTALK > 65dB

LINE 20Hz ∼ 20kHz ±1dB CHANNEL CROSSTALK > 75dB

MIC >60dB POWER SUPPLY

12V ADAPTOR

LINE >75dB DIMENSIONS（W×H×D）

294

105

382

WEIGHT 5.0kg

OUTPUT

SECTION

FREQUENCY

RESPONSE

S/N RATIO

NOMINAL INPUT

LEVEL

MAXIMUM INPUT

LEVEL

IMPEDANCE

OWNER'S MANUAL

VMC-180E 04.10.8 7:03 PM ページ 1

Summary of content (6 pages)

PAGE 1
VMC-180E 04.10.8 7:03 PM ページ 1 SPECIFICATIONS NOMINAL INPUT LEVEL MAXIMUM INPUT LEVEL IMPEDANCE MIC MAIN/SUB（1/4' PHONE JACK） -50.0dBv -32.0dBv 3.3kΩ PHONO 1∼3L/R （RCA JACK） -46.0dBv -22.4dB v 47kΩ LINE 1∼5L/R （RCA JACK） -10.0dBv +11.6dBv 47kΩ INPUT SECTION 10KHz -∞ ∼ +4dB HI ISOLATOR MID 1KHz -∞ ∼ +4dB LOW 80Hz -∞ ∼ +4dB SECTION RATED OUTPUT MAXIMUM OUTPUT IMPEDANCE MASTER OUT L ／R（XLR JACK BALANCED） 0dBv +11.
PAGE 2
VMC-180E 04.10.8 7:03 PM ページ 3 CONGRATULATIONS！ Thank you for purchasing the Vestax VMC-180 Mixing Controller. We suggest that you read through this owner's manual thoroughly so that you may enjoy the full use of this product safely and in the knowledge of all its special features and suitable applications. A U T I O N 2 IMPORTANT SAFEGUARDS 3 F E A T U R E S 4 F U N C T I O N S 5 PROGRAM INPUT SECTION 6 MIC.
PAGE 3
VMC-180E 04.10.8 7:04 PM ページ 5 FUNCTIONS 15. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product dose not operate normally by following the operating instructions.
PAGE 4
VMC-180E 04.10.8 7:04 PM ページ 7 PROGRAM INPUT SECTION t PGM ISOLATOR【HI】 1 2 3 4 8 5 6 7 9 10 11 12 q INPUT SELECTOR Used to select input (2 line or 1 phono) to be sent to each PGM channel. w PGM TRIM This control is used to adjust the input level volume for the best possible sound. When making adjustments to the "TRIM" of an input, try and ensure that the signals level only occassionlly goes in to the "RED" range.
PAGE 5
VMC-180E 04.10.8 7:04 PM ページ 9 HOW TO CHANGE THE FADER UNIT HOW TO CHANGE THE INPUT FADER UNIT REAR PANEL SECTION fig.a Notes 37 38 36 34 ・Please match the size of the screwdriver to the screw. Using a wrong screwdriver may damage the screw. ・DO NOT touch the PCB board that is set on the rear of the cover.It may cause damage. ■change to "IF-180" ①Remove the fader knobs.
PAGE 6
VMC-180E 04.10.8 7:04 PM ページ 11 CONNECTION HOW TO CHANGE THE CROSS FADER UNIT ■change to "CF-PCV" ①Remove the fader knobs. (see fig-a) ②Remove the bottom cover. (see fig-b) ③Remove the 2 screws which fix the crossfader unit, and remove the fader unit from position in mixer. (see fig-c) ④Carefully remove the multi-cable connector from the fader unit. (see fig-d) ⑤ Remove the screws which fix the crossfader volume. (see fig-e) ⑥ Remove the knob and the panel of new a new fader unit "CF-PCV".