Technical data

Call Control 1-28
Chapter 1: Basic System Features
SBX IP Programming & Operations Guide
Allow Table A - -used to check whether the dialed
digits by COS 2 and COS 4 station is matched with
the allowed toll pass digits. NOTE: Allow table A is
only used when the COS of dialed station is COS 2
or 4.
PGM 224 + FLEX 1 + VALUE
(refer to Allow Table) + Allow
Number (max 14 digits; 0-9, #,
*, Don't Care) + [HOLD/SAVE]
VALUES --
Range = 01-30
Deny Table A -- used to check whether the dialed
digits by COS 2 and COS 4 station is matched with
the denied toll pass digits. NOTE: Deny table A is
only used when the COS of dialed station is COS 2
or 4.
PGM 224 + FLEX 2 + VALUE
(refer to Deny Table) + Deny
Number (Max 14 Digits; 0-9, #,
*) + [HOLD/SAVE]
VALUES --
Range = 01-30
Allow Table B -- used to check whether the dialed
digits by COS 3 and COS 4 station is matched with
the allowed toll pass. NOTE: Allow table B is only
used when the COS of dialed station is COS 3 or 4.
PGM 224 + FLEX 3 + VALUE
(refer to Allow Table) + Allow
Number (Max 14 Digits; 0-9, #,
*) + [HOLD/SAVE]
VALUES --
Range = 01-30
Deny Table B -- used to check whether the dialed
digits by COS 3 and COS 4 station is matched with
the denied toll pass digits. NOTE: Deny table B is
only used when the COS of dialed station is COS 3
or 4.
PGM 224 + FLEX 4 + VALUE
(refer to Deny Table) + Deny
Number (Max 14 Digits; 0-9, #,
*) + [HOLD/SAVE]
VALUES --
Range = 01-30
Allow Table C -- used to check whether the dialed
digits by COS 8 station is matched with the allowed
toll pass digits. NOTE: Allow table A is only used
when the COS of dialed station is COS 8.
PGM 224 + FLEX 5 + VALUE
(refer to Allow Table) + Allow
Number (Max 14 Digits; 0-9, #,
*) + [HOLD/SAVE]
VALUES --
Range = 01-50
Deny Table C -- used to check whether the dialed
digits by COS 8 station is matched with the denied
toll pass digits. NOTE: Deny table A is only used
when the COS of dialed station is COS 8.
PGM 224 + FLEX 6 + VALUE
(refer to Deny Table) + Deny
Number (Max 14 Digits; 0-9, #,
*) + [HOLD/SAVE]
VALUES --
Range = 01-50
Allow Table D -- used to check whether the dialed
digits by COS 9 Station is matched with the allowed
toll pass.
NOTE: Allow table B is only used when the COS of
dialed station is COS 9.
PGM 224 + FLEX 7 + VALUE
(refer to Allow Table) + Allow
Number (Max 14 Digits; 0-9, #,
*) + [HOLD/SAVE]
VALUES --
Range = 01-50
Deny Table D -- used to check whether the dialed
digits by COS 9 Station is matched with the denied
toll pass digits. NOTE: Deny table B is only used
when the COS of dialed station is COS 9.
PGM 224 + FLEX 8 + VALUE
(refer to Deny Table) + Deny
Number (Max 14 Digits; 0-9, #,
*) + [HOLD/SAVE]
VALUES --
Range = 01-50
If programming FLEX 1-4, you must re-enter PGM 224 to gain access to programming of FLEX 5-8 and vice versa.
Release 3.5
June 2010