Service manual

12
Operating Manual Reprint
Court Blip: Courtesy Blip
When this parameter is set to “on,” this function causes
the VXR-7000 to send out a “blip” on the portable/mobile
radio is frequency each time the portable radio is unkeyed.
This provides audible confirmation to the user that the
VXR-7000 was able to receive the transmission from the
portable.
Press the [S
PACE] bar to toggle “on” or “off.”
Rev Bst: Reverse Burst.
When this parameter is set to “on,” the CTCSS tone
signal’s phase is inverted just before the repeater turns to
receive. This allows the portable/mobile station’s CTCSS
Decoder to begin switching off, thus reducing the transi-
tion time required.
Press the [S
PACE] bar to toggle “on” or “off.”
DCS Typ: DCS Format
This command is effective only when DCS is chosen for
squelch control.
A = “Normal” DCS
B = “Inverted” (complement) DCS
Press the [S
PACE] bar to select the desired DCS Type.
DDec Type: DCS Decoder Type
This command selects the manner in which DCS is to be
decoded.
Fixed = Decodes only the type selected in above pa-
rameter (DCS Typ: Normal or Inverted).
Auto = Both types (Normal and Inverted) will be de-
coded.
Press the [S
PACE] bar to select the desired DCS Decoder
Mode.
Multi Tone: Enable/disable Multi Tone Operation
Press the [S
PACE] bar to toggle Multi Tone Operation be-
tween selections “yes” and “no.”
Press the [E
NTER] key to
display the “M
UL TI TONE
SELECT” window, from
which you may select a
CTCSS tone or DCS
code; move the cursol to
the appropriate field
you using the [A
RROW] key, then press the [ENTER] key to
open the “T
ONE SELECT” or “CODE SELECT” window. Now
select the desired CTCSS tone or DCS code using the [A
R-
ROW] key, then press the [ENTER] key again to accept the
selected tone or code, or press the [E
SC] key to cancel.
You may set as many as 16 CTCSS tones and/or DCS
codes.
Note that, if you do not yet program a CTCSS tone or
DCS code in the “M
ULTI TONE SELECT” window (when
the “M
ULTI TONE SELECT” window data is not pro-
grammed), press the [S
PACE] bar to display the “MULT I
TONE SELECT” window directly.
CWID ANI/ENI: Select the Identifier mode
Press the [S
PACE] bar to toggle the selections “CW ID,”
“ANI/ENI,” or “off.” To select this feature to the “CW
ID” or “ANI/ENI,” the “CW ID” parameter must be en-
abled via the dealer programming.
Action Mode: Select the repeater operation mode
Press the [S
PACE] bar to toggle between “Duplex” opera-
tion or “Simplex” operation.
Tx Freq.: Edit Transmit Frequency
Use the [0] - [9] keys to enter the desired channel fre-
quency directly, and press the [E
NTER] key.
CTCSS Encoders: Toggle CTCSS Encoder ON/OFF,
sets CTCSS Frequency
Press the [S
PACE] bar to toggle the CTCSS Encoder “on”
or “off,” or press the [E
NTER] key to display the “TONE
SELECT” window, from
which you may select a
CTCSS frequency using the
[A
RROW] key; press [ENTER]
again to accept the selected
tone, or press the [E
SC] key
to cancel.
DCS Encoders: Toggle DCS Encoder ON/OFF, sets DCS
Code #
Press the [S
PACE] bar to toggle the DCS Encoder “on” or
“off,” or press the [E
NTER] key to display the “CODE SE-
LECT” window,
from which you
may select a DCS
code using the
[A
RROW] key;
press [E
NTER]
again to accept
the selected code, or press the [E
SC] key to cancel.
Base TOT: Enable/disable the Time-Out Timer while in
the “BASE” station mode
Press the [S
PACE] bar to toggle the TOT feature selects
“yes” and “no.”
The TOT time is determined via dealer programming.
Base Guard: Enable/disable the Base Guard Feature
When this parameter is set to “yes,” the transmitter will
be inhibited for a few seconds before the repeater (in the
“BASE” station mode) turns to receive.
The inhibit time is determined via dealer programming.
LOUT: Select the Lock Out Feature’s mode
Press the [S
PACE] bar to toggle the Lock Out Feature be-
tween “BCLO,” “BTLO,” or “off,” then press the [E
N-
TER] key to accept the setting. “BCLO” inhibits transmit-
ting while there is carrier present. “BTLO” inhibits trans-
mitting while there is carrier present unless there also is a
valid tone present.