Product Card
Table Of Contents
- Cloud Services Gateway 300 Series
- At a Glance
- CSG300 Appliance Models
- Chassis Views
- CSG300 Series Appliance Specifications
- Chassis Specifications
- CSG300 Series Appliance SKUs
- Regulatory Compliance
- Certifications
- Export Control Information
- Front and Rear Panel Components
- Front Panel
- Rear Panel
- Additional Information
- Network Interface Card Modules
- LTE Modem Module
- Embedded WiFi Module
- Interface Numbering
- Power Supply and Airflow
- AC Power Supply
- Airflow Requirements
- Installation Guidelines
- General Safety Guidelines
- Federal Communication Commission Interference Statement
- Prepare the Site for Installation
- Site Preparation Guidelines
- Environmental Requirements
- Rack Requirements
- Airflow Requirements
- Install a CSG300 Series Appliance
- Unpack a CSG300 Series Appliance
- Packing List for a CSG300 Series Appliance
- Mount a CSG355 or CSG365 Appliance in a Rack
- Connect a CSG300 Series Appliance
- Step 1: Connect Earth Ground to a CSG300 Series Appliance
- Step 2: Connect AC Power to a CSG300 Series Appliance
- Step 3: Configure a Management Console to Connect to a CSG300 Series Appliance
- Step 4: Connect a CSG300 Series Appliance to a Management Console
This equipment complies with CE and FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Warning: Operation of this equipment in a residential environment could cause radio interference.
Warning: Operation of this equipment is for indoor use only.
IC Wireless Interference Statement
This series appliance contains licence-exempt transmitters or receivers)that comply with Innovation, Science, and
Economic Development Canada’s licence-exempt RSSs. Operation is subject to the following conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage.
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage estsusceptible d’en
compromettre le fonctionnement.
To satisfy RF exposure requirements, a separation distance of 20 cm or more must be maintained between the antenna
of CSG300 series device and persons during device operation. To ensure compliance, operations at closer than this
distance is not recommended.
Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de
moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la
position centrale de l’ antenne.
Thess radio transmitters IC:2417C-EM7455 and 26338-CSGW1 have been approved by Innovation, Science, and
Economic Development Canada to operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type
listed are strictly prohibited for use with this device.
• LTE EM7455 modules—Radio transmitter IC: 2417C-EM7455
◦ Gain of antenna: 3.23 dBi maximum
◦ Type of antenna: 50 ohm, Dipole
• WiFi CSG-W1 modules—Radio transmitter IC: 26338-CSGW1
◦ Gain of antenna: 4.55 dBi maximum
◦ Type of antenna: 50 ohm, Dipole
Le présent émetteur radio IC:2417C-EM7455 and 26338-CSGW1 a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
https://docs.versa-networks.com/Versa_Internal/WIP/Antony/Cloud_Services_Gateway_300_Series
Updated: Tue, 01 Dec 2020 03:50:36 GMT
Copyright © 2020, Versa Networks, Inc.
21