Operating instructions

16
RFSDV34 Freestanding Direct Vent Gas Stove
10003550
Venting Requirements and Options
Approved Vent System Components
The heater must be vented to the outdoors through an
adjacent exterior wall or through the roof. The venting
system must be comprised of the appropriate listed vent-
ing components specied on this page. These parts are
available from Selkirk Corporation, DuraVent Corporation
or your Vermont Castings Group Dealer.
Vermont Castings Group Vent Components
The following kits are available to meet the needs of most
installations. Consult your dealer about other vent parts
that may be appropriate to complete the installation.
Starter Kit 7TFSSK
Starter Kit - Vertical Venting 7TDVSKV
for 7TDVSKV-A order 1/ t o 61 roof pitch
for 7TDVSKV-B order 7/1 to 1/1 roof pitch
for 7TDSKV-F order at roof
45° Elbow Kit for vertical installation offsets 7TFSDV45
90° Transition Elbow Kit 7TFSDV90
for Vertical Sidewall Applications or Through-the-Roof
Telescopic Vent Sections
1” to 18” Adjustable Length 7TDVP118
35” to 64” Adjustable Length 7TDVP3564
Pipe Sections for Vertical or Horizontal Venting
4 per box 7TDVP8”
4 per box 7TDVP1”
7TFSDVP4”
7TDVP36”
7TFSDVP48”
Firestop Spacer 7DVFS
Attic Insulation Shield 7DVAIS
Vertical/Horizontal Combination Offset Support 7DVCS
DuraVent Components
www.duravent.com
Phone: [phone]9, Fax: [phone]
Minimum Horizontal Vent Kit 2792
Starter Pipe Assembly (incl. inner & outer sections) 768*
90° Elbow, Blk. 46DVA-E90B*
45° Elbow, Gal. 46DVA-E45
6” Straight, Blk. 46DVA-D6B*
9” Straight, Blk. 46DVA-09B
11” - 14B⁄₈” Adjustable Straight Section 46DVA-08AB
1” Straight 46DVA-1
4” Straight 46DVA-4B*
36” Straight 46DVA-36B
48” Straight 46DVA-48
Horizontal Vent Cap 46DVA-HC*
Wall Plate 46DVA-DC
Vinyl Siding Shield 46DVA-VSS
Snorkel Termination - 14” 46DVA-SNK-14
Snorkel Termination - 36” 46DVA-SNK30
Wall Strap 46DVA-WS
Cathedral Ceiling Support Box 46DVA-CS
Storm Collar 46DVA-SC
Wall Thimble 46DVA-WT
Firestop Spacer 46DVA-FS
Selkirk Corporation Vent Components
www.selkirkcorp.com
1301 W. President George Bush Highway Ste. 330
Richardson, TX 75080
Phone: 1-800-99-8368, Fax: [phone]
Appliance Adapter 4DT-AAV
90° Elbow, Blk. 4DT-EL90B
45° Elbow, Blk. 4DT-EL45B
6” Straight, Blk. 4DT-06B
9” Straight, Blk. 4DT-09B
4” - 10” Adjustable Straight Section, Blk. 4DT-AJ1
1” Straight, Blk. 4DT-1B
18” Straight, Blk. 4DT-18B
4” Straight, Blk. 4DT-4B
36” Straight, Blk. 4DT-36B
48” Straight, Blk. 4DT-48B
Horizontal Vent Cap 4DT-HC
Wall Plate 4DT-WT
Vinyl Siding Shield 4DT-VS
Snorkel Termination - 14” 4DT-ST14
Snorkel Termination - 36” 4DT-ST36
Wall Strap 4DT-WS/B
Cathedral Ceiling Support Box 4DT-CCS
Storm Collar 4DT-SC
Firestop Spacer 4DT-FS
Flashing 0/1 - 6/1 4DT-AF6
Flashing 6/1 - 1/1 4DT-AF1
Steel Chimney
Horizontal Kit A 4DT-HKA
Horizontal Kit B 4DT-HKB
Vertical Kit 4DT-VKC
Masonry Chimney Kit 4DT-MCK
Vertical Termination Cap 4DT-VC
Flashing 0/1 - 6/1 46DVA-F6
Flashing 6/1 - 1/1 46DVA-F1
Steel Chimney Conversion Kit
Kit A (6B⁄₈” - 8B⁄₈”) 46DVA-KCA
Kit B (6B⁄₈” - 10¹⁄₂”) 46DVA-KCB
Kit C (6B⁄₈” - 13”) 46DVA-KCC
Masonry Chimney Kit 46DVA-KMC
Vertical Termination Cap (High Wind) 46DVA-VCH
Vertical Termination Cap (Low Prole) 46DVA-VC
*Included in Minimum Horizontal Vent Kit #79
All DuraVent Straight vent pipe sections have a net length 1¹⁄₂”
(37 mm) less than the nominal dimension; i.e., a 6” (15 mm)
Straight pipe section has an effective length of 4¹⁄₂” (115 mm).