Model VCS5007 Shown USER’S MANUAL for Models VCS4027 G as Barbecue Grill (Propane & Natural Gas) 50004060 12/06 Rev.
Warnings DANGER If you smell gas: 1. Shut off gas to the appliance; 2. Extinguish any open flame; 3. Open lid; 4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department. WARNING Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
Warnings SIGNAL WORDS: The Signal Words used in this Manual, and their intended meanings, are as follows : DANGER: Indicates that a failure to observe the safety instructions could result in death or catastrophic bodily injury. WARNING: Indicates that a failure to observe the safety instructions could result in serious bodily injury. CAUTION: Indicates that a failure to observe the safety instructions could result in property damage or minor bodily injury.
Warnings A. SAFE LOCATIONS FOR USE OF THIS OUTDOOR GRILL DANGER: Never use this outdoor Grill inside any building, garage, shed or breezeway, or inside any boat, trailer or recreational vehicle, to prevent a possible fire and to prevent the possibility of carbon monoxide poisoning or asphyxiation. WARNINGS: Always confirm that this Grill is not positioned under a combustible object (e.g., an awning or umbrella) or in a covered area (e.g., a porch or gazebo) before lighting it, to prevent a possible fire.
Warnings B. SAFE USE OF LP (PROPANE) GAS DANGER: Never install a propane cylinder that is more than 80 % full, as the contents may lack adequate room for expansion when exposed to heat. Propane vapor may then be vented through the pressure release valve, which could accumulate in a pool and later result in a fire or explosion. Always instruct your certified propane fuel supplier to confirm by weight that your cylinder is not more than 80 % full. An empty cylinder will weigh about 19 lb.
Safety Always promptly shut off the gas supply and immediately extinguish all flames if you smell gas. Always seek assistance from your gas supplier or local Fire Department if the gas smell persists, because of the danger of fire or explosion. Always confirm that there are no gas leaks before lighting this Grill. Apply a 50/50 solution of liquid soap and water to the gas supply line connectors with a brush or spray bottle, and watch for bubbles. Never use a match or open flame to test for gas leaks.
Safety FUELS WARNING: Never use Natural Gas in a Grill that has been configured to burn Propane Gas, and never use Propane Gas in a Grill that has been configured to use Natural Gas, to avoid possible bodily injury. Always consult the Rating Label on the back of your Grill to confirm which fuel must be used with the Grill. WARNING: Use only the pressure regulator and type I propane gas supply coupling and hose that is originally provided with this appliance or as specified, (see Fig. 2).
Safety DANGER: a) Do not store a spare LP - Gas Cylinder under or near this appliance b) Never fill the cylinder beyond 80% full; and c) If the information in a) and b) is not followed exactly, a fire causing death or serious injury may occur. WARNING: Always confirm that the openings in the cylinder compartment of the Grill are free of any obstructions that would restrict the circulation of ventilation air.
Gas Hookup Hooking Up to the LP (Propane) Gas Supply FOR YOUR SAFETY 1. WARNING: Never store or use gasoline or any other volatile substance in the vicinity of this Grill. 2. WARNING: Never store a spare propane cylinder in the vicinity of this Grill, or in the vicinity of any other potential heat source. LP (PROPANE) GAS SUPPLY CONNECTION 1. Always place the propane tank in the tank locator hole in the bottom pan of the cylinder compartment and insure it is secured into place. 2.
Gas Hookup NATURAL GAS SUPPLY CONNECTION TO CONNECT: 1. Push back the Sleeve on the Socket as shown below (see Fig. 6a). 2. Insert Plug and release the Sleeve (see Fig. 6b). 3. Push the Plug until Sleeve snaps forward to lock the Plug in the Socket. Retract Sleeve Fig. 6a WARNING: Always conduct the following safety tests before lighting the Grill, to prevent a possible fire or explosion (see leak test below). TO DISCONNECT: 1. Push Sleeve back and pull the Plug out. Release Sleeve Release Sleeve Fig.
Operation CONTROL FUNCTIONS PROPANE TANK VALVE WARNING: Never open the Tank Valve unless the Grill is being prepared for use, to prevent the pooling of propane vapor. Always open the Valve immediately before lighting the Grill, and always close it immediately after cooking has been completed. BURNER CONTROL VALVES (see Fig. 7) On Models VCS3507, VCS3517 & VCS3507BI, there are three independent control valves for the main burners, and a separate control valve for the rotisserie burner (if equipped).
Operation NOTE: When lighting the grill for the first time, burn with the main burners on HIGH for at least 30 1. a. Always open the Hood completely and always inspect the Grill minutes, to burn off any manufacturing residues. LIGHTING THE MAIN BURNERS and burners to confirm that all components are properly positioned before lighting the main burners. b. Make sure the grease cup is empty and grease tray is clean. c.
Operation TURNING THE BURNERS OFF 1. Always turn the burner control knob(s) to the OFF position when cooking has been completed. 2. Promptly turn OFF the gas supply valve at the propane cylinder or at the main natural gas supply line. 3. Close the Hood of the Grill. FLARE-UPS “Flare-ups” sometimes occur when food drippings fall onto the hot sear plates or burners and ignite. Some flaring is normal and desirable, as it helps impart the unique flavors associated with grilled foods.
Operation LIGHTING THE ROTISSERIE BURNER (if equipped) The Rotisserie burner provides the steady, even heat required to cook poultry and roasts to self-basted perfection. TO START THE ROTISSERIE BURNER: 1. Always open the Hood completely before attempting to light the Grill. WARNING: Never stand with your head directly over the Grill when preparing to light the Rotisserie burner, to prevent possible bodily injury. 2.
Operation ROTISSERIE SETUP (if equipped) The Rotisserie burner is intended to be used for rotisserie cooking only. WARNING: Never use the main burners while using the Rotisserie burner, as that could result in igniting the drippings, or overheating your Grill, which could result in damage of the Grill. The Rotisserie assembly includes a counter-weight for large or irregular food items ; using the counterweight will reduce the strain on the motor. 1. Remove the warming rack.
Operation LIGHTING THE SIDE BURNER (if equipped) WARNING: Never stand with your head directly over the Grill when preparing to light the side burner, to prevent possible bodily injury. 1. Turn the side burner control knob to HIGH (see Fig. 13). 2. Turn the Igniter Knob clockwise until the burner ignites. The burner should light within four clicks of the igniter. NOTE: Some models are equipped with an electronic ignter. Refer to page 6 for respective piezo and electronic igniter systems.
Troubleshooting Guide Burner will not light ACTION REQUIRED POTENTIAL CAUSE PROBLEM Gas supply turned off Turn on fuel supply and retry. Out of propane Confirm the flow of gas by smell or by listening for the hiss of gas being emitted. Allow gas to clear before attempting to relight. Weigh your propane cylinder. A standard 20 lb. cylinder will weigh about 19 lb. when it is empty and 39 lb. when it is 80 % full. WARNING: Never take a propane cylinder indoors for any purpose.
Troubleshooting Guide PROBLEM Uneven burn pattern or Flashback fire ACTION REQUIRED POTENTIAL CAUSE Blockage in the burner or gas system Confirm that the venturi tubes are not blocked by insects or other debris. Use a special venturi brush to clean (Fig. 15). Use a pin or needle to probe the orifice in the gas valve. Never enlarge the orifice (Fig. 16). Use a small nail or toothpick to clean the burner ports (Fig. 16).
VCS4007 / VCS4017 / VCS4027 / VCS4037 VCS5007 / VCS5017 / VCS5027 / VCS5037 ASSEMBLY PROCEDURES Tools Required: knife or scissors, Phillips or Robertson (square head) screwdriver.. Model VCS4007 Shown Step 1: Unpack Carton and Verify Contents Use a sharp cutting tool to cut the straps on the packaging and then lift off the carton top. The sleeve surrounding the barbecue can be removed by lifting it straight up and over the top of the unit.
VCS4007 / VCS4017 / VCS4027 / VCS4037 / VCS5007 / VCS5017 / VCS5027 / VCS5037 Assembly Step 2: Install the Casters Parts Required: (4) Casters, (1) Block (not included) Note: Casters (wheels) may differ from those shown in the illustration depending on the model you purchased. Select a side to begin installing the casters. Place a block of wood, a telephone book or anything else available approximately 6 inches thick -under the side to support the weight of the barbecue.
VCS4007 / VCS4017 / VCS4027 / VCS4037 / VCS5007 / VCS5017 / VCS5027 / VCS5037 Assembly Slide Parts Required: (1) Left Side Shelf Support (1) Left Condiment Tray (1) Right Side Shelf Support (1) Right Condiment Tray (8) 1/4-20 x 1-1/2“ Bolts Push Step 4: Install the Side Shelf Supports Bolts Bolts Note: Only the right side assembly is shown in Fig. 4a and Fig. 4b. To install Left Side Support and Condiment Tray, repeat this step for the left side.
VCS4007 / VCS4017 / VCS4027 / VCS4037 / VCS5007 / VCS5017 / VCS5027 / VCS5037 Assembly Step 6: Secure Shelves Fig. 6 Parts Required: (4) 10-24 x 1/2” Bolts (black) A. Secure each Shelf by inserting (2) 10-24 x 1/2” bolts through the U-Clip fasteners as shown in the diagram. B. Tighten the four (4) Shelf Support bolts from Step 4 to secure the shelf supports to the grill body. A. Insert Bolts Repeat Steps 5 & 6 for the opposite side of the grill. B.
VCS4007 / VCS4017 / VCS4027 / VCS4037 / VCS5007 / VCS5017 / VCS5027 / VCS5037 Assembly Step 9: Attach Side Burner Lid (S/B-Single) Parts Required: (1) Side Burner Lid (S/B-Single) (2) #10-24 x 3/4” ( 1/4” Shank)* * Included with the Side Burner Kit Bolts Attach the lid marked (S/B-Single) to the Shelf Right top marked VM-S/B using two #10-24 x 3/4” ( 1/4” Shank) bolts. Align the holes at the back sides of the lid with the holes located in the shelf top and insert a bolt in each.
VCS4007 / VCS4017 / VCS4027 / VCS4037 / VCS5007 / VCS5017 / VCS5027 / VCS5037 Assembly Step 12: Attach the Handle to the Door Parts Required: VCS4007/VCS4017/VCS4027/VCS4037: (1) Handle VCS5007/VCS5017/VCS5027/VCS5037: (3) Handles Note: Handles may not appear exactly as shown in diagram Attach the Door handle(s) to the door(s) by aligning the handles over the holes and inserting the screws that were supplied with the handles through the door panel and into the handles.
VCS4007 / VCS4017 / VCS4027 / VCS4037 / VCS5007 / VCS5017 / VCS5027 / VCS5037 Assembly Step 15: Install the Internal Components Parts Required: VCS4007 / VCS4017 : VCS4027 / VCS4037 (4) Sear Plates (3) Cooking Grates (1) Warming Rack VCS5007 / VCS5017 : VCS5027 / VCS5037 (5) Sear Plates (4) Cooking Grates (1) Warming Rack Carefully place each of the Sear plates side by side inside the barbecue, making sure the semicircular finger groove is facing toward the front of the grill.
VCS4007 / VCS4017 / VCS4027 / VCS4037 / VCS5007 / VCS5017 / VCS5027 / VCS5037 Assembly Step 17: Install the LP Cylinder (LP Models Only) Parts Required: (1) LP Gas Cylinder (not included) Note: Check your user’s manual for the cylinder filling requirements, how to attach the regulator and how to test for leaks before you try lighting the grill. Caution: Make sure the hose is not touching any hot surfaces.
CFM Corporation 410 Admiral Boulevard Mississauga, Ontario L5T 2N6 Canada (800) 668-5323 www.cfmcorp.com Service Note: If you are experiencing difficulties or are dissatisfied with your purchase, please contact CFM at the telephone number listed above prior to returning your grill to the store.
