Install Instructions

ManualsBrandsVeris ManualsHVAC Supplies8" Duct Temperature Sensor with Mounting Box, 10k Ohm NTC Type 2 Thermistor

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classied locations.

•

Read and understand the instructions before installing this product.

• Turn o all power supplying equipment before working on it.

• The installer is responsible for conformance to all applicable codes.

If this product is used in a manner not specied by the manufacturer, the protection

provided by the product may be impaired. No responsibility is assumed by the

manufacturer for any consequences arising out of the use of this material.

Installation Guide

Temperature

Product Identication

Product Overview

TD, TF, and TG temperature sensors monitor the temperature of the air inside a duct. The probe is available in

multiple lengths to suit multiple applications. All models have standard resistive outputs compatible with building

control systems, and all models are warranted for a period of ve years.

TD/TF/TG Series

Duct Mounted Temperature Sensors

Specications

Wiring 22 AWG; 2-wire RTD/Thermistor

Housing Stainless Steel

Mounting Location Not suitable for wet locations. For indoor use only.

WARRANTY

Limited Warranty 5 years

COMPLIANCE INFORMATION

Agency Approvals CE

Enclosure Probe Length

B = 4" (102 mm)

C = 6" (152 mm)

D = 8” (203 mm)

E = 12” (305 mm)

F = 18” (457 mm)

K = 36” (914 mm)

D = Duct

F = Duct w/

mounting box

G = Duct w/ water

resistant housing

Cal Certiﬁcate

0 = None

2 = 3-point NIST calibration

Sensor Type Output

= Resistive

B = 100R platinum, RTD

C = 1k platinum, RTD

D = 10k T2, Thermistor

E = 2.2k, Thermistor

F = 3k, Thermistor

H = 10k T3, Thermistor

I = 1k Balco (Nickel-iron) RTD

J = 10k Dale, Thermistor

K = 10k w/11k shunt, Thermistor

M = 20k NTC, Thermistor

N = 1800 ohm, Thermistor

T = 100k, Thermistor

W = 10k T2 high accuracy, Thermistor

Y = 10k T3 high accuracy, Thermistor

RØ

Summary of content (2 pages)

PAGE 1
Installation Guide Temperature TM TD/TF/TG Series TG TF TD, TF, and TG temperature sensors monitor the temperature of the air inside a duct. The probe is available in multiple lengths to suit multiple applications. All models have standard resistive outputs compatible with building control systems, and all models are warranted for a period of five years.
PAGE 2
TD/TF/TG Series Installation Guide TM Dimensions TD Model 1.5" (38 mm) 1.1" (28 mm) 2" (51 mm) 0.25"Dia. (6 mm) L TF Model 4.20” (106.68 mm) Available in 4”, 6”, 12”and 18” probe lengths 3.88” (98.60 mm) 1.78” (45.18mm) TG Model 0.7" (18 mm) 2.9" (74 mm) Foam Gasket 2.5" x 2.5" (64 mm x 64 mm) 4.6" (117 mm) 0.25"Dia. (6.3 mm) 2.0" (51 mm) Installation L 1. Drill a 3/8” diameter hole into a duct for the sensor probe. 2. Insert the probe into the duct. 3.