VF02
Dear Customer, Thank you for purchasing the Verilux® EasyFlex® Natural Spectrum® Deluxe Floor Lamp. You have received an innovative and quality manufactured product, backed by a three-year limited warranty. As a Verilux® customer, your satisfaction means everything to us. We look forward to serving you now and in the future. Many other healthy lighting products are available through our catalog and online. To request a free copy of our catalog, call our toll-free number 1-888-544-4865.
IMPORTANT SAFETY INSTRUCTIONS CAUTION: • TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT DISMANTLE. THERE ARE NO SERVICEABLE PARTS INSIDE. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY: • Turn off/unplug and allow to cool before replacing bulb or cleaning.
GENERAL PRECAUTIONS • Do not use with power supply voltage other than 120V AC • Avoid placing the lamp in areas that are dusty, humid/moist, lack ventilation, or are subject to constant vibration. • Not for use with light dimmers, timers, motion detectors, voltage transformers, or extension cords. • Do NOT use lubricating agent in bulb assembly. • The light bulb may become loose during transit. To reinstall the light bulb, see the bulb installation instructions on page 9.
GETTING STARTED Main Parts & Controls B C A. Ergonomic Handle B. Lamp Head C. High/Off/Low Switch D. Gooseneck E. Shaft F. Ergonomic Height Adjustment Lever G. Lamp Base H. Power Cord I. Ballast J. LED Indicator K. Bulb L.
GETTING STARTED cont. Please read instructions carefully before using the EasyFlex® 1. Unpack lamp carefully, removing all packaging material, and confirm you have all parts shown in the diagram. For your convenience the bulb has been pre-inserted into the socket. 2. Remove all pieces from box. Locate 2 screws and tightening tool, in plastic bag, and set aside. 3. Detach red plastic pieces and store them in the event you need to return the lamp. 4.
ASSEMBLY HEADER INSTRUCTIONS 1. Set lamp base on the floor and insert the lamp shaft over the base support unit until the screw holes line up as shown in Fig. 1. Insert the screw using the tightening tool and turn clockwise to tighten. Close-up of screw hole in the lamp base Fig. 1 2. Hold upper shaft with one hand, release ergonomic height adjustment lever by gently pulling it upward as shown in Fig. 2. Extend the upper shaft approximately 12”. Lock lever by gently pushing it downward.
ASSEMBLY INSTRUCTIONS cont. 3. Attach the lamp head gooseneck to the shaft until the screw holes line up as shown in Fig. 3. Use care when tucking the wire into the shaft. Form a loop with any excess wire prior to tucking it. Insert the screw using the tightening tool and turn clockwise to tighten. Fig. 3 Close-up of screw hole in the lamp head 4. Remove the light diffuser from the protective plastic bag. Insert the plastic pegs at the bottom of the light diffuser into the openings near the bulb socket.
ASSEMBLY INSTRUCTIONS HEADER cont. 5. Attach the ballast to the power cord. Use care to align the 4-pin plug properly. DO NOT FORCE - the power cord is designed to connect only one way. 6. Plug ballast into a standard 120V 50/60Hz outlet. Turn lamp on. The green LED indicator (J) on center of the ballast will illuminate. If not, please refer to the troubleshooting section of this manual. (See page 10) J Note: Green LED indicator will not illuminate if lamp is turned off or bulb is removed.
BULB REPLACEMENT Removal 1. Unplug lamp from power source. 2. To access the bulb, remove grid diffuser by depressing the tab and lifting it out. (See Fig. 5 at right) 3. Firmly hold bulb base (B) and pull bulb (C) from the socket (A) in an outward motion. (See Fig. 6 below) Installation Fig. 5 1. Unplug lamp from power source. 2. Firmly hold base (B) and push bulb (C) into the socket (A). 3. Be sure bulb is firmly seated in the socket (see Fig. 7 below) and snapped into the metal bulb clip (D). 4.
TROUBLESHOOTING Before requesting service on your Verilux® lamp please read the following: • Make sure all power connectors, cords, and plugs are inserted fully and securely. • Make sure there is power to the wall outlet or try another outlet – not connected to a dimmer. CARE & CLEANING Your Verilux® lamp is made from high quality materials that will last for many years with a minimum of care.
Three-Year Limited Warranty ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED FOR REPAIR OR REPLACEMENT! Many questions may be answered by visiting www.Verilux.com, or you may call our customer service department at 1-888-544-4865 This limited warranty is provided by: Verilux, Inc.
