Installation Guide

7 MOC.TOPEDEMOH
March 06, 2024 Please contact 1-866-843-8453 for further assistance.
Pressure Sensitive (dry-to-touch) Applications: Lay tiles from the
center of the room in a pyramid fashion while
working towards the walls
as shown in Figure 3. The dry, tacky adhesive makes it possible to work
on top of the material without compromising the installation.
Wet-Set Applications:
can be installed while working off of freshly installed tiles. This will keep
tiles from shifting, minimize adhesive displacement, and prevent wet
adhesive from oozing up and getting onto the surface of the tiles. This
can be accomplished by creating work zones outlined with parallel chalk
arm reach and in multiples of the tile width. Measure and snap chalk line
parallel to the established base line. Spread adhesive within the work
zone, and begin installing tiles using the row-by-row method, as shown in
Figure B under “LVT Resilient Plank Installation” (next section).
TIP: Do not apply more adhesive than can be worked within
the recommended working time. Always follow the adhesive
manufacturer’s recommendations.
IMPORTANT:
roller after installation. Use a hand roller in areas that cannot be reached
with a 100lb roller.
PLANK INSTALLATION
STEP 1: SQUARE THE ROOM
Locate the same point at the other end-
wall. Snap a chalk line between these
points to mark the center line on the
center point, mark off a line across the
line. This can be accomplished using the
3-4-5 triangle method. Starting from the
center point, make a mark measuring
4 feet vertically and 3 feet horizontally.
Connect the marks with a diagonal line
to complete the triangle. If the diagonal line does not measure exactly
5 feet, then the center crossing lines are not at a true right angle. (See
Figure A)
TIP: For large rooms, multiples of the above dimensions may be
used to obtain greater accuracy. (6-8-10, 9-12-15, and so on.)
STEP 2: INSTALL THE PLANKS
After snapping the center starting chalk
lines, spread the appropriate adhesive
on the center lines, leaving portions of
the lines at center and near each wall
uncovered. Start laying the planks from
the right angle formed by the center
lines. Lay the material from the center of
the room, working towards the walls as
placed precisely and accurately against
the reference line as you install. Make
line and tight against the adjoining plank.
The ends of the planks should align
perfectly. Lay row-by-row or in pyramid
fashion (See Figures B & C).
TIP: Pay special attention to the edges of the planks. Do not slide the
planks through the adhesive as you install.
IMPORTANT:
roller after installation. Use a hand roller in areas that cannot be reached.
Note: Bond issues resulting from the use of non-recommended
adhesives are not warranted. All warranties and guarantees
pertaining to the suitability and performance of any product
not recommended rests with the material manufacturer or the
issues resulting from the use of non-recommended, improper,
or
incorrectly prepared adhesives, sealers, embossing levelers,
patches, concrete, gypsum-based products and other such items,
are the sole responsibility of the installer and/or manufacturer of
CARE & MAINTENANCE
LVT DRYBACK GENERAL CARE & MAINTENANCE
cured urethane and ceramic bead coating, which provides improved
maintenance characteristics and options for the end-user in commercial
many problems can be prevented before they occur. The area of usage,
and frequency of maintenance needed. Proper care and maintenance
These guidelines will help to maintain the appearance of and extend the
FLOOR-CARE BEST PRACTICES
• Sweep or vacuum daily; use only vacuums without beater bars.
mats at all outside entrances.
• Avoid the use of rubber-backed mats, as certain rubber compounds can
permanently stain vinyl.
• In order to prevent indentations and scratches, provide glass, plastic,
wide for the legs of heavy furniture or appliances. Equip swiveled-type
casters at least 2” in diameter. Remove small diameter buttons from
the legs of straight chairs and replace with metal or felt glides that have
bearing surfaces no less than 1" in diameter.
• Never use anything coarser than 3M-equivalent red cleaning pads
section).
• The use of aggressive strippers, such as mop-on/mop-off, no-scrub and
no-rinse strippers, may affect the adhesive bond.
cigarettes, matches, or other extremely hot items can damage LVT
• Only use premium cleaning products that are designed for Luxury Vinyl
common spills. However, any spill should be cleaned up immediately.
• Avoid exposure to direct sunlight for prolonged periods. The use of
drapes or blinds is recommended during peak sunlight hours. Prolonged
exposure to direct sunlight can result in discoloration, and excessive
temperatures might cause tiles or planks to expand.
Figure A
3’
5’
4’
Figure B
Row by Row
Figure C
Pyramid
Product Description
Dryback LVT/LVP
Installation Method
Glue Down