VEREX Director User's Guide V4.
Contents Welcome ..................................................................................................................................................... 1 Entering an Area and Disarming the System .......................................................................................... 2 Welcome to VEREX Director .................................................................................................................. 4 Start-up and Logging In .........................................
Checking Power Levels (V4.4) ........................................................................................................... 86 Checking the Status of Modules ........................................................................................................... 88 Suite Security System Messaging ........................................................................................................ 90 Checking Status or Controlling a Suite Security System ..................................
Advanced Sorting..................................................................................................................... 189 Users and Holidays Shared Across Multiple Accounts ....................................................................... 190 Introduction .............................................................................................................................. 190 Phase 1: Account-Specific Data.........................................................................
Serial Port Installation and Set Up ........................................................................................... 298 Windows Settings Required ..................................................................................................... 298 Software Installation for a Fresh/New System ......................................................................... 300 Upgrading from an Earlier Version of Software........................................................................
Before You Begin (Form-by-Form Data Entry) ......................................................................... 335 Basic Settings for Testing, and Panel Communications........................................................... 336 Importing Settings from an Existing VEREX Director System Panel ....................................... 338 Customizing the MyTools Bar ............................................................................................................. 339 System Capacities .......
Copyrights and Trademarks Disclaimer ™ VEREX Director, G-Prox, and Netvision are trademarks of UTC CCS Systems ™ Pentium is a trademark of Intel Corporation ® Microsoft, Windows, Windows 2000, and Windows XP, are trademarks or registered trademarks of the Microsoft Corporation. All software, firmware, drawings, diagrams, specifications, catalogues, literature, manuals and other supplied materials shall constitute the proprietary information of the manufacturer.
Welcome 21-0381E v4.9.
Entering an Area and Disarming the System Reader/Door Mode Area Setting Disarmed (Off) Locked & Card Only Locked & Card+PIN Present card, open the door Present card, enter PIN open the door Armed & 'Auto Disarm on Valid Token' Armed & 'PINOnly' or 'ID+PIN' Present card, open the door Present card, enter PIN open the door Present card, open the door. Then log into panel and disarm it. Present card, enter PIN open door. Then log into the panel & disarm it.
If the door is unlocked, access is not controlled (simply open the door to enter the area). Conversely, if the door is locked, and all cards are presently 'locked out', users will be unable to enter. Card Number: As an alternative to the user ID number (UID), and/or access cards, the system can be set for entry and login using the card number instead (4-10 digits).
Welcome to VEREX Director shut down the software (incl. the communications or server module), then start the software and login again. Start-up and Logging In Multiple Instances: Beginning with Director v4.70, you can run multiple copies of the interface (…Director.exe). This allows you to access different features and/or different accounts at the same time. Starting the VEREX Director Software Select Start, Programs, VEREX Director V4, and VEREX Director, and wait for the start-up screen to appear.
- Password: The operator's assigned password. Default Operator Name & Password: Operator, 1234 The default login name and password take effect only until changed by a system administrator. To protect against unauthorized access to the software, the default password should be changed right away.
Note: Port 443 must be 'open' on the network for the Director-server. Exiting, Logging Off, or Changing Operators Shutting Down the VEREX Director Software To shut down the VEREX Director software, click the X in the extreme upper-right corner of the VEREX Director screen (or open the File menu, and select Exit). Tip: If you changed any desktop settings, and would like to retain them, be sure to click the check-box provided. Then, select "Yes" on the confirmation screen.
The Desktop Your 'Window' to the System Navigating the Desktop The desktop is your interface to the VEREX Director software, providing a familiar Windows 'look and feel', with access to all features and items assigned to you as a VEREX Director operator. The VEREX Director interface can be set as desired by each individual operator. This includes whether they prefer the MyTools bar, or the Tree window, plus the sizing of the desktop sections, and other settings.
Resetting the Desktop After moving and resizing areas of the screen, you may wish to reset the desktop to either your last saved settings, or to the initial factory default layout. Last Saved Settings: Click Reset on the toolbar (or open the View menu, and select Desktop Settings, and Reset). Factory-Default Layout: Open the View menu, and select Desktop Settings, and Default).
Tip: You can save your desktop changes at any time: Open the View menu, select Desktop Settings, & Save. Note: You will also be asked if you want to save your changes whenever you logout or exit from the software Selecting Desktop Items to be Displayed The [Tree], [MyTools] and [Events] buttons on the toolbar allow viewing or hiding different aspects of the desktop (try it!). Listing Items Panel-by-Panel vs.
Listing Configuration and Control & Status Topics in the Tree as a Single List: 1) Click your account/site button in the tree. ("View" menu when a Configuration or Control & Status Topic is Selected in the Tree) Multi-Account Systems: First select [Account Folders] in the 'tree', and double-click an account. 2) Right-click a topic in the tree (or open the View menu), and check to ensure that Logical Tree View is selected.
Running Reports, and Monitoring System Activity 21-0381E v4.9.
Time-and-Attendance Reporting In/Out Status Tracking: This feature requires "User In/Out Status Tracking" to be enabled. Related Setting: YourAccount, Account Information, Setup (tab), "Enable User In/Out Status for this Account" Time and Attendance Reports Cardholder time and attendance reporting allows generating reports pertaining to the presence (roll-call), tardiness, number of hours at work, etc. for users pertaining to a specific account.
If Printing an Attendance Report To print a report without viewing it first: Select the type of report and other criteria as usual, and select Printer as the destination. Then, select Run, and click OK when the 'Print' screen appears. Tip: To select a different printer click Printer, and make your selection from the 'Print Setup' screen that appears. To view a report before printing: Select the type of report and other criteria as usual, and select 'Screen' as the destination. Then, click Run.
Reports Time and Attendance Screen Reference Report Period - From and To (date): The beginning and end date from the event log to be checked for cardholder activity. (Change the values manually, or click the arrow to access a pop-up calendar.) Note: Roll-call and In/Out status reports use the previous 48 hours as a date/time range (instead of the "From" and "To" settings).
Searching by Name: For reports that allow searching by user-name, you can enter the 1st or last name only, 1st and last name (separated with a space), or "LastName, 1stName". If searching for a first or last name, you can enter the first few characters plus an asterisk (e.g., nam*). Custom User Field: This pertains to (optional) custom user information categories that can appear at the bottom of the 'User' screen. Note: Reports cannot be filtered on multi-line fields.
Required-Attendance Time-Periods Attendance Periods Attendance periods are weekly blocks of time that allow time & attendance reports to 'know' when users are supposed to be in the facility. Schedules for cardholder access must span a larger period of time than the applicable attendance period--to let people enter the facility before their shift begins, and leave after it ends.
Reports Time and Attendance Attendance Period Screen Reference Pick-Lists (bottom of the Form) - Attendance Period (bottom of form): This is where you select an attendance period to view or edit.
Roll-Call Reports (v4.61) In/Out Status Tracking: This feature requires "User In/Out Status Tracking" to be enabled. Related Setting: YourAccount, Account Information, Setup (tab), "Enable User In/Out Status for this Account" An instant roll-call feature has been added to the status toolbar. This sends a roll-call report for your monitored account to your default Windows printer. (The report will list persons on an area-byarea basis.
Reporting on System & Personnel Activity screen(s) that appear (details to follow). Activity Reports Activity reporting allows viewing or printing a listing of various types of events that have occurred for a specific account. A date/time range can be specified, and the report can also be limited to a specific area, device, person, etc. TechTip: Reports pertaining to past events are based on the present event list, plus any archived data that has been re-imported using the archive feature.
user information categories that can appear at the bottom of the 'User' screen. Note: Reports cannot be filtered on multiline fields. Be sure to make your selection with this in mind. Show on Resolution: This lets you have the list include events depending on whether or not they have been 'resolved' (i.e., dealtwith). "All": This shows all events--including ones not associated with the comment/resolution feature.
(Remaining Buttons) Tip: You can scroll within the form and/or resize the window to view additional items when necessary. (Click Reset on the toolbar to reset the desktop.) - [File...]: This allows changing the location and file-name for a report being saved for future viewing, printing, etc. Tip: Use a different name each time to avoid overwriting previous reports. - [Reset]: This provides a quick way to reset/clear the "Search for" criteria and other selections on the form.
Reporting on Previous Guard-Tours Guard Tour Reports If Printing a Guard Tour Report Guard tour reports allow viewing or printing a listing of events pertaining to previous guard tours for a specific account. A date/time range can be specified, and the report can also be limited to specific items such as guard tour alarms, or the guard arriving early or late. To print a report without viewing it first: Select the type of report and other criteria as usual, and select Printer as the destination.
Event Period - From and To (date and time): The beginning and end date from the event log to be checked for guard-tour events. Reports Guard Tour Tip: You can change the dates manually, or click the arrow to access a pop-up calendar. To set the times, click within the 'hours' or 'minutes', and use the up/down arrow keys. Event Type - The various guard tour events to be included in the report (the guard arriving late, etc.). Select the ones that you want included).
Reporting on User Access Authorities (by Area, Door, or Floor) User Access Reports User-access reports provide a list of the persons with authority to access a specific area, door, or floor on specific weekdays and times. You can also list: Cards that have expired; Cards that will expire in the future (selectable date-range); Cards that have not been used since a specific date; Cards identified as being 'Lost' • Cards that have not been used in selected area(s) (selectable daterange).
Inactive Cards: This lists cards that have note been used since a selected date. Tip: You can change the date numerals manually, or click the arrow to access a pop-up calendar. Lost Cards: This lists cards that have been identified as 'lost'. User names and IDs will be included in the report for cards set as 'Lost' through the "Users" screen.
refer to "Working with the Report Viewer". - [Run]: This runs the report based on your selected criteria. Additional screens will appear depending on your selections (such as the printer selection form, report viewer, etc.). 26 Verex Director V4.9.1 User's Guide 21-0381E v4.9.
Reporting on Users, System/Device Settings, etc. Customizable Reports The VEREX Director software allows viewing or printing a listing of programmed information in your system. This includes settings for the system, areas, devices, panel users, etc. Related Topic: You can also link to the database and set up custom queries of nearly any scope and content.
Reports Users; Reports Panel Configuration - Type (Panel Config. Reports only): The desired topic to be covered by the report (areas, doors, etc.). Note: Reports pertaining to "Areas" and physical devices (modules, doors, etc.) are available only for operators with the applicable 'Configuration' permissions. - (Columns): Data fields/settings to be included in the report. Tip: The "Group" column in panel config. reports pertains to the "Panel Group" (e.g., location) for the specific panel.
Reporting on Operator Audits or Panel Communications Logs Audit Reports Audit reporting allows viewing or printing a listing of changes made by operators, or records of panel communications sessions. A date/time range can be specified, and the report can also be limited to desired criteria. TechTip: Reports pertaining to past events are based on the present event list, plus any archived data that has been re-imported using the archive feature. See: "Exporting or Importing Activity or Audit Logs".
Reports Audit Report Log Period - From and To (date and time): The beginning and end date from the audit log to be scanned for the report. Tip: You can change the dates manually, or click the arrow to access a pop-up calendar. To set the times, click within the 'hours' or 'minutes', and use the up/down arrow keys. Client/Server Systems: Times are stored as GMT in the database, and adjusted for correct display in the time-zone at each specific workstation.
at a later time. Allows you to change the location and/or filename if desired. Tip: See the item-descriptions if you need help. (Remaining Buttons) - [File...]: This allows changing the location and file-name for a report being saved for future viewing, printing, etc. Tip: Use a different name each time to avoid overwriting previous reports. - [Reset]: This provides a quick way to reset the search criteria (to "Operator" audit report, and find "All" audits).
In the next screen, locate and select Reports Panel Diagnostic the desired archived report (.raf), and click Open (or simply double-click the file). For details on viewing and printing displayed reports, refer to "Working with the Report Viewer". Screen Reference (Top of the Form) - Panel: Select the panel you are interested in here. - Diagnostic Reports: The middle of the screen shows a list of diagnostics logs/reports that you can select from.
Working with the Report Viewer The Report Viewer When a report is set to be viewed, it appears with a toolbar allowing: When Viewing a Report Viewing different pages of the report; Setting the portion of each page that will be visible at one time (zooming in or out); Selecting a printer, and/or setting the pages to be printed; Printing the report.
Monitoring System Activity Alarm and Activity Monitoring The System Monitoring Window Alarm and Activity Monitoring through the VEREX Director System The monitoring window shows the alarms and activity messages for the account selected in the tree (double-click an account to select).
Split Screen Mode (Show Alarm Window) Connecting to the Associated Panel(s), An Overview: For operators set to "Show Alarm Window", unacknowledged alarms will appear in a separate window at the top. For the latest up-to-date messages, you must be connected with the associated panel(s). (Otherwise, you will see only messages that were received previously).
window 'undocked' and hidden behind the main desktop, open the View menu, select Desktop Settings, and then Default. To adjust the size of the monitoring window, position the mouse cursor at the top of the window, watching for the cursor to change shape. Then, click-and-drag the top of the window to the desired new position. To maximize the size of the monitoring window, double-click its title-bar twice. To restore the VEREX Director desktop at any time, simply click Reset on the toolbar.
(Photo-Verification)". - [Filter]: Allows resorting the event / monitoring window, limiting the list to show specific types of messages only, and/or only messages that have not been 'resolved' (see last 2 items below, plus "Limiting the Window to Show Only Specific Messages".); - (Activity Messages): Each message shows: A colored bar for the message priority; The date and time the event occurred; The type of event/message; Details on the specific event.
When you Click [Filter] Screen Reference - Sort Order By: This allows listing messages in order by date/time only, or showing 'unresolved' (and higher priority) events first. - Filter on Resolution: This lets you have the list include events depending on whether or not they have been 'resolved' (i.e., dealt-with). All: This shows all events--including ones not associated with the comment/resolution feature (i.e., not set as 'resolvable').
(Click the Coloured Box for an Alarm Message) Acknowledging Alarms (Comment / Resolve) Alarm Notes / Comments While responding to alarms, you can enter a note for each alarm describing what caused it, what was done to correct the problem, etc. You can also set the alarm as 'resolved' ( ), or 'Keep Unresolved' ( ? ). Tips: Whether 'Resolved' or not, alarms will be considered to be 'Acknowledged'--unless you click [Cancel].
Opening a Video Event When Messages Cannot be Transmitted to the VEREX Director Software If the VEREX Director software is not connected with the specific panel, messages are not transmitted, and each individual panel will retain up to 65,536 of the latest events that occurred. Exception: Remote (dial-up) panels with their own dedicated external modem (i.e. one panel per modem) can be set to automatically 'dial-in' and transmit messages to the Director software.
(Click the Camera Symbol for a Video-Event Alarm Message) Screen Reference - Vertical Slider bar on the right: This indicates your relative position within the recorded video during playback. For recordings associated with a video event, a dark band will show when the triggering event occurred within the recording. Tip: This is used as the default starting location for playback. - (Play Previous Clip): Plays the video recording saved immediately prior to the present one (at the NetVision PC).
Visually Verifying Users (Photo-Verification) Photo-Verification Connecting to the Associated Panel(s), An Overview: Introduction Each operator can select door(s) to have the stored photo for entrants displayed each time someone gains access (or is denied entry) at any of the selected door(s). The last 1, 4, or 9 entrant's photos can be displayed. The photo can then be used to verify each entrant's identity.
Using This Feature The photo window opens automatically whenever a person gains access at the specific door. View (menu) Photo Verification Show (or when a person enters at the specific door) Multi-Account Systems: This works only while the specific account is selected. (Click [Account Folders] in the 'tree', and doubleclick the specific account.) You can also open the photo window manually by clicking [Show Photo] at the bottom of the monitoring window.
View (menu) Photo Verification Customize Setting up This Feature Each operator can set the photoverification feature to suit their preferences. Authorities: This feature is available to all operators. Steps: 1) Multi-Account Systems: Ensure you are 'in' the desired account. (Click [Account Folders] in the 'tree', and double-click the specific account.) 2) From the View menu, select Photo Verification Customize. 3) Refer to the selection-descriptions for this screen while making your selections.
Guard-Tours: Monitoring Connecting to the Associated Panel(s), An Overview: 1) See if you're already connected by checking the status bar at the bottom of the monitoring window. Introduction to Guard Tours Guard Tours A guard-tour can be thought of as either: A path that must be completed by a guard in a certain amount of time—including stations (checkpoints) along the way, or; The process of the guard making his/her way through the assigned route.
Activating and Monitoring Guard Tours (that have already been set up) Activating a Guard Tour (Adding it to the Guard Tour Monitor) Initiate a connection with the associated panel(s) as described previously / above. Then, select Guard Tour Monitor from the MyTools bar, or click your site/account button in the tree, 'open' Control & Status (click the "+"), and select Guard Tour Monitor. Multi-Account Systems: First select [Account Folders] in the 'tree', and double-click the desired account.
Control & Status Guard Tour Monitor Screen Reference - Monitor Tour (bottom of form): This is where you select an active guard tour to view its progress/status. This area shows the name of the guard tour (as defined under "Guard Tour"); - General: This area shows the 'tour' being monitored, plus the name of the guard (user), and the defined action to occur if the guard is late or absent at any of the stations (checkpoints).
Guard Tours: Initial Set Up Overview Viewing or Changing Settings for a Guard Tour To set up a guard-tour: 1) 2) Ensure the applicable readers and other guard-tour stations (checkpoints) have been defined in the system. Select Guard Tours from the MyTools bar, or click your site/account button in the tree, and select Guard Tours. Guard tour inputs require a "Custom Point Type" with the "Preprocess" set as "Guard Tour" (and the "Level" set as "24 hours").
Guard Tours Screen Reference - Guard Tour (bottom of form): This is where you select a guard tour to view or edit (or "New Tour" to add a new one). This area shows a reference number assigned by the system, and the name of the guard tour, once defined; - Name: A suitable name / description for the guard-tour. Tip: Be sure to change this from the default setting of "New Tour".
Guard Tours [Select Station] (or [Edit] ) - Doors and Input Points (top of the form): This is where you select the specific door or inputpoint pertaining to the guard-tour station being added or changed; Area Selections: See "Automatic Area Disarming / Rearming", to follow / below. To be available here, the specific areas and devices must already be defined in the system.
Checking Status and Controlling Items 21-0381E v4.9.
Maps and Video (Visual Monitoring & Status/Control) Status and Control Using Visual Director Welcome to Visual Director (Map/Camera Views) The 'Views' Toolbar Beginning with V4.0, VEREX Director includes a customizable visual interface for viewing live cameras, monitoring alarms, and controlling items. We call this "Visual Director". The "Views" toolbar provides access to all map/camera views that are presently set up.
Accessing This Feature (Visual Director) See if you're already connected with the panel(s) by checking the status bar at the bottom of the monitoring window. Multi-Account Systems: First select [Account Folders] in the 'tree', and double-click the desired account. If not presently connected, initiate a connection as described previously/above.
Use the scroll bars provided, or; Use the "Universal Scroll" feature of your mouse (if it is set up for this). Locating Items on a Complex Map, and Filtering to Show Fewer Items at a Time Tips: The map will automatically shift to display the selected item. For status & control details, see a following section / below. To temporarily limit a map to show only a specific type of devices / objects: When You Right-Click a Blank Spot on a Map Zoom: 3) 4) Click within the desired map.
Control & Status Panel Control & Status Visual Director Screen Reference - Item (bottom of the form): This allows you to find a specific item on a complex map; Tip: Making selections here is well-suited for complex maps. For simpler maps, you'll likely prefer to scan the map visually. For status & control details, see a following section / below. - Filter: This allows temporarily limiting a selected map to show specific types of devices only (click the small downarrow to see the available choices).
Viewing the Status of an Area or Device Area and Device Status (Mouse hovered over an item) Open the applicable "View", and (locate) and select the desired device (Details: Previous/above). Then, 'hover' your mouse cursor on top of the item, and watch for a popup status screen. Jumping to the Control & Status Form: Right-click the area or device and select "Switch to Control & Status Screen for this Item" from the pop-up menu.
Controlling an Area or Device Open the applicable "View", and (locate) and select the desired device (Details: Previous/above). Then, right-click the device and select your desired action from the pop-up menu. Jumping to the Control & Status Form: Right-click the area or device and select "Switch to Control & Status Screen for this Item" from the pop-up menu. Dealing with Alarms To return the Event/Monitoring Window to Its Previous State: Click [Return to Previous Filter] at the bottom of the window.
the door for a duration equal to the "extended unlock duration". This is the same as a user who is set for "extended unlock/challenged" gaining entry with an access card or token. - Pending Unlock: This is an unlock command that waits for one person to enter the facility at the specific door. - Grant Last User -- Reader 1 (or 2): If the last user at a reader was denied access, this will issue a 'Momentary Unlocking', and log that card/user as being granted entry.
Camera Status/Control and Adjustments Introduction A number of camera controls are provided, allowing you to: Aim or zoom PTZ cameras; Check connection status; Adjust image quality, etc. These features are provided through the video toolbar in each camera-image, with additional camera settings available under: Tools, Options. The Video Toolbar When working in a 'view' that contains a camera-image, a small button in the bottomleft corner will provide access to the video toolbar.
Controlling a Pan/Tilt/Zoom Camera Then hover over the Camera-Image You can easily aim or zoom any camera that supports Pan-Tilt-Zoom operation. Initial Set Up: PTZ cameras must be identified and properly set up. Details: Step 1b: Define Cameras (under "Initial Set Up of: Views, Maps, Cameras", to follow). User Permissions: Only one person can control a specific PTZ camera (COM port) at a time.
Checking Camera/PTZ Connection Status Camera and PTZ connection status can be viewed at any time. Steps: 1) Open the 'View' that contains the desired camera-image. MyTools Bar: Visual Director (+User login if prompted). Tree: Control & Status, Panel Control & Status (+User login if prompted), Visual Director. Then, select from the 'Views' toolbar (top-right). 2) Open the video toolbar by clicking the button in the bottom-left corner of the camera-image. Then, click the 3rd button ("View Messages").
Setting the Maximum CameraImage Size Camera-images auto-size relative to the window they are displayed in. Exception: To avoid jagged looking images, you can set the maximum displayed image-size for each camera. Steps: 1) Open the 'View' that contains the desired camera-image. MyTools Bar: Visual Director (+User login if prompted). Tree: Control & Status, Panel Control & Status (+User login if prompted), Visual Director. Then, select from the 'Views' toolbar (top-right).
Tools (menu) Options (Visual Director ) Adjusting Camera Quality for your Connection/Bandwidth Various camera-Image quality settings are provided to allow for slower connection speeds and reduced-bandwidth applications. Notes: These selections affect all cameras for the selected account. Features pertaining to maps and cameras are not supported with single-panel licensing.
Initial Set Up of: Views, Maps, Cameras running.) Introduction to Map/Camera Set Up Supported Map File Formats The IP address (or name) of each specific capture station PC must be known; The capture station "Video Server" must be set to allow anyone to view cameras (through the Windows Control Panel); The desired camera number should be known; For control of PTZ cameras (pan-tilt-zoom), you will need to have a valid PTZ username for each specific capture station.
Visual Director Customize Views Maps Step 1a: Define Source Maps Map image files need to be identified - [Add]: Allows identifying a new map image; to the system before they can be Note: Scalable graphics work best (EMF, WMF), and are recommended--especially for more detailed maps. displayed. Topic Locator: MyTools Bar: Customize Views, (login with a user name & ID if needed), select the Maps .
Step 1b: Define Cameras Cameras need to be identified before they can be displayed by the Director software. Topic Locator: MyTools Bar: Customize Views, (login with a user name & ID if needed), select Cameras . In the Tree: Click your site/account button in the tree, open Control & Status, and Panel Control & Status (click the "+"), and login with your user ID and PIN if prompted for this. Then, select: "Visual Director" (click the "+"), Customize Views, Cameras.
Visual Director Customize Views Cameras [Add] (or right-click a camera in the list and select "Edit Camera") Tip: This can be an IP address, or a name (FQDN). Contact your IT rep. for assistance if needed. Note: To view cameras, a connection must be available. If unsure, go to a command prompt and try 'pinging' the IP address.
Note: For a PTZ camera, the same user name and password is typically used for viewing cameras and PTZ-control. - Timezone: For embedded DVRs (e.g., VeDVR / NVe). Select the timezone associated with the DVR unit here. Notes: This setting is used with video events. For other types of DVRs, this is handled internally, and this field will be greyed-out. - (camera display area): A sample image from the selected camera indicates a valid connection. (See next item.
Step 1c: Define Camera-Views Visual Director Customize Views Camera-Views (this is required only for event-triggered camera-views) As an alternative to fixed cameras appearing in different locations onscreen, camera-views can be thought of as 'locators' that allow you to set where specific types of eventtriggered camera images will appear (separately for each 'view'). Each camera-view shows the last-triggered camera associated with it.
Visual Director Customize Views Step 2: Set up Views "Views" are definable layouts for maps and camera images. These must be set up to allow viewing maps and/or cameras. Topic Locator: MyTools Bar: Customize Views, and (login with a user name & ID if needed). In the Tree: Click your site/account button in the tree, open Control & Status, and Panel Control & Status (click the "+"), and login with your user ID and PIN if prompted for this. Then, select: "Visual Director" (click the "+"), Customize Views.
Step 3a: Place Items onto Maps (Doors, Sensors, etc.) Visual Director Customize Maps Customizing maps pertains to placing objects on specific maps to enable visual monitoring, and status/control features. Attention: Items added to a specific map here will appear on that map in every 'view' that contains it. (To avoid this, you can copy a map and save it as a new one, or create new map(s) using the same image file. For details, see step 1a.
Step 3b: Set Up Event-Triggered Camera-Views Doors and sensors on maps can be associated with a 'camera-view' to trigger a camera when selected events occur at the device (access denied, sensor tripped, etc.). Visual Director Customize Maps (right-click an item) Advanced Camera Settings Notes: This feature pertains to individual 'views' (i.e., the map and 'camera-views' must be on the same 'View', and the camera images will be visible only when that 'view' is displayed.
Checking Status & Controlling Items account). 2) If not connected, check to ensure the communication software is running on the specific PCs. Introduction to Status & Control The Status and Control Feature VEREX Director can monitor the status of most system, area, and device aspects, and allows controlling the system on an area-by-area basis, or for individual doors or input points. Also See ( V4.
tree, open Control & Status, and Panel Control & Status (click the "+"), and login with your user ID and PIN if prompted for this. Then, select your desired topic in the 'tree' (under "Panel Control & Status"). If 'Panel-Groups' and 'Panels' are Listed Under Control & Status: Select (open), your desired panel-group and panel if these are listed in the 'tree'. Tip: "Control & Status" (and configuration) topics can be set to display either as a single list, or on a panel-by-panel basis.
Using the Status Toolbar The Status Toolbar The Status Toolbar The status toolbar allows monitoring for various items (sirens, fire alarms, other alarms, and trouble conditions), and provides a quick way to view the details for each item. Multi-Account Systems: You can set the account to be monitored by the status toolbar (when each operator is logged in) by clicking [Monitor] on the far-right end of the toolbar. This can also be set in the screen for each operator.
Monitor (from the Status Toolbar) Selecting the Account to be Monitored by the Status Toolbar For systems with multiple accounts, you can set the account to be monitored by the status toolbar (for each operator who is logged in): Click Monitor on the far-right end of the toolbar (or open the View menu, and select Change Monitor Account). Then, select your desired account, and click OK. When finished, save your changes by opening the View menu, selecting Desktop Settings, and then Save.
Miscellaneous Status Tasks Panel Date and Time VEREX Director lets you check the date and time stored at a system panel, compare it with that at the host computer, and adjust the panel's date / time to match the computer, if necessary. 'difference' value to see if the panel date and time need to be changed. If you need to set the date and time at the panel to match the VEREX Director computer, click [Set Panel Time with Server Time].
Screen Reference Control & Status Panel Control & Status System (Date/Time Portion) -Panel (bottom of the form): This is where you select a desired panel (for systems with more than one). Alternative: You can also set the 'tree' to list status topics on a panel-by-panel basis. For details, refer to "Other Desktop Choices". - Panel Time Zone: This shows the 'time zone' for the specific panel. If different from the PC/server time zone, any clock updates will be adjusted accordingly.
Resetting Users' Antipassback Status Antipassback (APB): A feature that blocks individual cards from being used to: + Re-enter the same area, or; + Re-enter the facility from 'outside', and/or; + (Optional): Enter other areas; …Unless they are recorded as exiting first--i.e., each person must use their card/token at every reader they encounter (that is set to "Detect Antipassback"). Tip: This helps to protect against unauthorized card usage.
Control & Status Panel Control & Status System (Antipassback) Screen Reference -Panel (bottom of the form): This is where you select a desired panel (for systems with more than one). Alternative: You can also set the 'tree' to list status topics on a panel-by-panel basis. For details, refer to "Other Desktop Choices". Anti-Passback - [Anti-Passback Reset]: This opens a small screen that allows resetting the antipassback status for a single user, or all users for doors associated with selected panel(s).
Clearing a "Bad Card/PIN Global Lockout" Global User Lockouts Control & Status Panel Control & Status The 'Bad Card/PIN' tracking feature System [Clear User Lockout] helps to prevent unauthorized persons 'hacking' their way into a controlled area. All users can be locked out automatically if a lot of invalid cards and/or PINs are detected during a set time.
Checking System Status (Remote Diagnostics) Control & Status Panel Control & Status This feature allows you to check the System ("Get System Status" portion) Remote Diagnostics status of a number of hardware and communications aspects of a panel. Attention: This feature is supported for xL panels only (narrow rectangular mainboard). Tip: You can also run reports based on previous status/diagnostic sessions.
- On This Screen: This shows various physical status aspects for the specific panel. - [Print]: This allows printing the onscreen diagnostic data. Control & Status Panel Control & Status System [Get System Status] Tip: A print-setup screen will appear— allowing you to select a printer, and set up the print-job as desired. - [OK]: This saves the on-screen data (internally), and closes the Remote Diagnostics screen. Tip: You can also run reports based on previous status/diagnostic sessions.
Checking the Status of Panels (Equipment) Panel Status (Equipment) Conditions Monitored for Each Panel Working with This Screen When the status screen appears, use the Grid / Form toolbar-button to select your preferred view-mode. Various conditions (such as low battery, tampering, etc.) can be monitored for each panel. This helps to maintain the integrity of each system panel. Forms view: All equipment topics on a graphical screen; Grid View: A list of monitored equipment topics.
Control & Status Panel Control & Status System Equipment -Panel (bottom of the form): This is where you select a desired panel (for systems with more than one). Alternative: You can also set the 'tree' to list status topics on a panel-by-panel basis. For details, refer to "Other Desktop Choices". - (top of screen): Status of various items pertaining to a specific account or site. - Fuse: Whether any of the fuses on this system panel has failed.
Checking Power Levels (V4.4) System Power Status Working with This Screen The power status screen allows you to check the status of various items pertaining to mains input voltage, battery life remaining, etc. When the status screen appears, use scroll bar at the bottom to view all items listed. Note: Some features are supported only by xL panels. Unsupported items will be shown as zero (0).
Control & Status Panel Control & Status System Power Screen Reference -Panel (bottom of the form): This is where you select a desired panel (for systems with more than one). Tip: "Control & Status" (and configuration) topics can be set to display either as a single list, or on a panel-by-panel basis. (To change the view: Right-click "Control & Status", and select or deselect Logical Tree View). For more information, refer to "Other Desktop Choices".
Checking the Status of Modules Grid View: All modules in a list. Module Status The module status screen shows the status of various items pertaining to each system module (keypad, door controller, etc.). Also See (Related Topics): + Checking the Status of Panels (Equipment) + Checking Power Levels Initiate a Connection, and Access this Topic See if you're already connected with the panel(s) by checking the status bar at the bottom of the monitoring window. Select a desired module in the list.
Screen Reference Control & Status Panel Control & Status System Equipment Modules - Module (bottom of the form): This is where you select a module to view its status. This area shows a reference number assigned by the system, plus the name/description of the module as defined under 'Configuration'. - Module Information: Information pertaining to the selected module (version number, maximum and present baud rate, etc.). - Module Status: Various status topics for the selected module.
Suite Security System Messaging The 'Suite Messaging' screen allows sending messages to the LCD Suite units (all or selected units). A message text can be up to 30 characters long. Note: (Director V4.80 and LCD Suite 1.3). The ISM Panel does not support this enhancement. Control & Status Panel Control & Status Suite Security Suite Messaging - Send message to: This is where you can select suite security keypads or you can use “All Suites”.
Checking Status or Controlling a Suite Security System Status of an Apartment/Suite or Facility The 'Suite Security' status screen shows the status of various items pertaining to each apartment or facility associated with a suitesecurity keypad, and allows silencing a suite keypad alarm, or changing a suite/facility arming level (V4.31). Note: Since each keypad typically pertains to a separate, privately-owned dwelling, any arming changes should typically be coordinated with the occupant. Also See ( V4.
Screen Reference - Security Suite State ( [Off], [Stay], and [On] ): These buttons show (and allow changing) the arming level of the suite/facility: Off (Disarmed); Stay: (Perimeter Armed); or ON (Fully armed). Control & Status Panel Control & Status Control Security & StatusDiagnostics Panel Control & Status Suite Suite Security Notes: Since each keypad typically pertains to a separate, privately-owned dwelling, any arming changes should typically be coordinated with the occupant. Prior to v4.
Checking Status or Controlling Items by Area "Area Users" Screen: A second screen is available as Control & Status - Area Users in the MyTools bar, or Area Users under "Areas " in the 'tree'. This pertains to the presence of user activity, the number of users in an area (user count), and resetting APB tracking for an area. Related Topic: Area Users (to follow).
adjust the closing time, click [Worklate], set the closing time as desired, and click OK. Tip: To adjust the time in 30 min. increments, use '<' or '>' respectively. For 1 hour adjustments, use '<<' or '>>'. For more permanent changes, you can adjust the schedule itself, and/or change assignments for the specific area. For details, refer to "Schedules for User Access and Area Automation", and "Areas and Related settings".
Screen Reference Control & Status Panel Control & Status Areas - Area (bottom of form): This is where you select an area to view its status or control items. This shows a reference number assigned by the system, plus the name/description of the area as defined under 'Configuration'. - [Off], [Stay], and [On]: These buttons indicate the present arming-level of the area, and allow arming/disarming an area as desired (if you have this authority).
Area Users (Activity, User Count, and APB-Reset) Control & Status - Area Users The "Area Users" screen shows / allows: Whether or not activity has occurred in the area. Control & Status Panel Control & Status Areas Area Users (This is based on users entering or leaving the area, and/or a custom 'Activity Monitor' input point being tripped.) The number of users presently in the area; Whether or not the area is full (i.e., contains the 'allowed' number of persons/vehicles).
Resetting the User-Count for an Area For areas set to 'count' the number of users that are present, you may need to reset the 'user-count' on a periodic basis (e.g., to correct for things such as users entering and/or exiting when someone else opens the door). Control & Status Panel Control & Status Areas Area Users [ Reset User Count ] Related Topic: "Configuration Areas Counting. To reset the 'user-count' for an area: Ensure you are connected with the specific panel(s) as described previously.
Resetting the Antipassback Status for Users in a Specific Area From time-to-time, persons may be unable to enter an area due to an antipassback violation (such as if they entered or exited when the system unlocked a door for someone else). This can be corrected by resetting the antipassback status for a specific area. Ensure you are connected with the specific panel(s) as described previously.
Checking User In/Out Status User In/Out Status Beginning with v4.2, VEREX Director can show the In/Out status for all users in an account. If the status screen is blank or inactive (or if you'd like more information), refer to "Accessing the Control and Status Topics for a Panel" (under "Checking Status & Controlling Items", previous).
Control & Status User In/Out Status Screen Reference In/Out Status Tracking: This feature requires "User In/Out Status Tracking" to be enabled. Related Setting: YourAccount, Account Information, Setup (tab), "Enable User In/Out Status for this Account" Notes: This feature operates in 'real-time', updating each time a person uses their card to gain entry through a door or gate. The screen may take a little while to activate/update.
Checking Status or Controlling Individual Doors Door Status and Control The door status screen shows the status of doors in the system, and allows controlling various parameters for each door (unlock a door, change operating characteristics, etc.) Elevator Readers: Door control does not apply to readers in elevator (lift) cabs. To control an elevator and/or its associated reader, refer to "Checking Status or Controlling Elevators".
Control & Status Panel Control & Status Doors - Door (bottom of form): This is where you select a door to view its status or issue commands. This shows a reference number assigned by the system, plus the name/description of the door as defined under 'Configuration'. If some Door numbers are missing: Elevator and door numbering is shared (1 32), but the elevators will not be listed here.
Checking Status or Controlling Elevators Elevator (Lift) Status and Control The elevator status screen shows the status of elevators in the system, and allows changing the operating characteristics for elevator readers. Selections are also provided to apply or remove access-control for all floors or individual floors--as accessed from a specific elevator (lift) cab.
To apply or remove access-control for all floors from this elevator cab, refer to the "Elevator Command" selections. Control & Status Panel Control & Status Elevators To change the reader access requirements or operating characteristics, refer to the "Reader 1 in Area X" selections. To apply or remove access-control (secure or desecure) for an individual floor--as accessed from a specific cab, refer to the "Elevator Floor Status" selections.
Checking Status or Controlling Floors Panel(s), An Overview" (under "Checking Status & Controlling Items", previous). Floor Status and Control The floor status screen shows the status of access-controlled floors in the system, and allows applying or removing access-control for specific floor(s)--as accessed from all elevator (lift) cabs in the system.
Elevators and/or specific floors can be set to desecure and resecure in-sync with a desired schedule. For details, refer to the configuration topic for elevators and/or floors. Control & Status Panel Control & Status Floors Screen Reference - Floor Command for All Floors and All Elevators: This allows applying or removing access-control for all floors and all elevators at the same time (requires appropriate authority).
Checking Status or Bypassing Input Points (Sensors) more information), refer to "Accessing the Control and Status Topics for a Panel" (under "Checking Status & Controlling Items", previous). Status of Monitored Sensors (Input Points) The 'point' status screen shows the status of monitored sensors, and lets you bypass a faulty sensor to allow arming an area.
Control & Status Panel Control & Status Points - Point (bottom of form): This is where you select an input-point to 'bypass', or view its status. This shows a reference number assigned by the system, plus the name/description of the input-point as defined under 'Configuration'. - Point Status: The present status of this sensor (input-point). - [Bypass] or [Remove Bypass]: Allows bypassing this input-point (to allow its area to be armed), or removing the bypass (to allow this sensor to be monitored).
Checking Status or Controlling Outputs (Electronically switched Devices) The 'Outputs' Control & Status Screen Viewing the Status of a Specific Output Outputs allow turning a self-powered electronic device on or off. The outputs control & status screen allows viewing the status of programmable outputs, and lets you control them manually when necessary. Use the Grid / Form toolbar-button to select your preferred view-mode.
Control & Status Panel Control & Status Outputs[Manual Control] Screen Reference - Output (bottom of form): This is where you select an output to control manually, or view its status. This shows a reference number assigned by the system, plus the name/description of the output as defined under 'Configuration'.
Panel Communications and Updates Beginning with V4.0 VEREX Director, you can use the Communications Wizard to set up and initiate communications with a panel. For more information, refer to "New Installation? Try the Wizard!" The initial topics in this section provide general information on panel communications. For an overview of the steps required to connect with a panel, refer to the installation topic "Panel Connection Overview".
Any workstation associated with your VEREX Director system can be used for panel communications. This requires: A proper physical connection (cable or modems); Settings as required for MS Windows and this software; The VEREX Director communications component being installed (and running) on each applicable PC. Note: With smaller sites (Single-panel / 300 users), remote management is also supported through the built-in dialler (Bell 103, 300 baud modem) on each panel.
Activating Communications and Transferring Panel Settings Panel Communications Sessions The Communications Pending/Online screen shows details on panel communications sessions (panel updates) that are either presently active, or scheduled for some time in the future. For communications / update sessions that have completed successfully, plus any attempts that may have failed, see "Viewing the Status of Previous Communications Sessions", to follow.
details, refer to "Communication Pools for System Panels". Update Requests Initiated from a Panel Update requests can be initiated from a remote/dial-up panel ( V2.0). This can be for a new panel that has not been programmed (known as being in 'cold boot' state). A service technician at a system keypad can also request a remote synchronization at any time. For details on initiating a remote update request from a keypad at a remote site, refer to the commissioning or installation guide for your system.
-Transaction Time (bottom of the form): This area allows selecting a communications session that is either presently in effect, or scheduled to occur sometime in the future. Communications Pending/Online Tip: Completed sessions (and failed attempts) can be viewed under "Completed" in the tree (see "Viewing the Status of Previous Communications Sessions", to follow.).
Communications Pending/Online [ Edit ] -Account / Panel / Group 'Tree' : The left side of this form shows the panel group(s) and panels to be associated with a communications session (find the desired panel, and then double-click to select it). (Communications Session Details) Note: This area lists only the panels that are not presently connected or otherwise associated with a current communications session.
maintain a 'Normal' connection after transferring or synchronizing settings, to allow for real-time monitoring (through the monitoring window), and checking status of items, or controlling items (through "Control & Status" in the tree). Viewing the Status of Previous Communications Sessions Tip: The most common reason for a failed communications session is a faulty physical connection, or incorrect communications settings.
Screen Reference Communications Completed - Comms Log (bottom of the form): This is a relative number for each update session, plus the date and time that each one occurred. Note: Session #1 is the most recent, while the highest numbered session is the oldest. - Log Date/Time: The date and time when the session finished. - Transaction Issue Date/Time: The date and time when the communication session was set up. - Account: The account/site associated with the panel(s) being updated.
Correcting Communication/Update Errors Tip: The most common reason for a failed communications session is a faulty physical connection, or incorrect communications settings. To set up an initial panel connection, refer to "New Installation? Try the Wizard!", or "Panel Connection Overview". Panel Version Mismatch: If you get an error due to a "Panel Version Mismatch", ensure your panel version is set correctly under: AccountName Account Information (Standard tab) "Panel Version".
VEREX Director, or a conflicting one at the panel, or; Edit a value right-away to correct a conflict. Same Unique Value Assigned to two Different Users Sometimes, you can choose to [Decide Later] on what data to use. In this case, the software data is retained, and the item (user, etc.) will appear with that setting highlighted in a different color.
Checking Account Status (V4.4) Related: Flash Firmware (>>) YourAccount Account Status Status Account Status The account status screen shows some status aspects for all panels in your selected account. The listed status elements pertain to communications sessions, panel firmware updates, and configuration errors. This is useful after a panel update session, and also to help troubleshoot problems with regular communications sessions.
Panel Firmware Files, and Updating Panel Firmware (V4.4) Activating Panel Firmware Files [Management] Panel Firmware Files Panel Firmware Files This screen allows you to 'activate' firmware update files (.FMW)—that is—to make them available to the VEREX Director software. Tip: Firmware update files (.FMW) can be obtained from your support representative or website. Be sure to keep your source files in a folder that is outside of the Director installation as backups.
Updating Panel Firmware Your Account Account Status Flash Firmware Flash Firmware This screen allows you to update panel firmware from any VEREX Director workstation. Note: In general, a panel firmware update does not affect configuration data stored at the panel. Before You Begin You and the workstation must have permission for this feature; The software must be set/able to communicate with the panel; "...Director Communications.exe" must be running—but with no connection to the panel yet.
..., [Start Download] On This Form - Panel: This shows the panel that is to be updated; - Current Version: This shows the firmware revision of the panel—as checked during the last communications session. - [Change File]: Allows selecting or changing the file to use for the panel firmware update. Tip: For files to be listed here, they must have been previously added to the Director software. Details previous/above.
Administration and Maintenance 21-0381E v4.9.
Operators (People Who Can Use This Software) Operators An operator is a person who has been given the authority to use the VEREX Director software. Each operator is given a 'login' name and password that provide access to specific items and features. Management Operator Operator The permission-set assigned to each operator determines what features they can use, and which items will be shown on the desktop. Also See: "Operator Permissions" (to follow).
of the help file will normally appear, although this can be changed if desired (for the current work-session). For details, look for the Language selection from the Help menu in the "Desktop Reference". - Permissions: This is a (previously defined) permission-set to be associated with this operator. This determines the features that will be displayed and/or available when this person is logged in. Also See: "Operator Permissions" (to follow). - Lockout Time (min.
Setting or Changing an Operator's Password Quickly Changing Your Password Open the File menu, and select Change Password. Then, enter the new password, press Tab, enter the password a second time, and press Enter (or click OK). Changing the Password for any Operator Select Operator from your MyTools bar, or click [Management] in the 'tree', open the Operator branch, and select Operator. Then, use the Grid / Form toolbar-button to select your preferred view-mode.
Operator Settings (v4.6) Operator Login Message Screen [Management], Operator, Operator Settings, An image and/or text message can Login be set to appear each time any operator logs in. This can be set/changed when desired by other operator(s) with the required permission. This provides an easy way for authorized operators to leave messages for operators arriving for the next shift or day.
Enhanced Operator Password Security [Management], Operator, Operator Settings, Security Operator password security has been enhanced through allowed characters, optional requirement to change the password periodically, and a configurable lockout feature has been added. Also See (Not to be Confused With): “The Auto-Lockout Feature” in the “Welcome” section of the Director online help or User’s Guide. Screen Reference This screen allows configuring various items pertaining to password security.
Operator Permissions Muti-Account Systems: Operator permissions are associated with account folders--allowing different types of permissions to be assigned to groups of accounts. Accounts and account folders need to have been set up appropriately. For details, refer to "Working with Accounts and Folders" (near the beginning of the Configuration section). Client/Server Systems: Permissions can also be assigned for each specific client workstation.
- Copy all Permissions: Copies into memory the permission settings for all account folders within a permissionset. - Paste all Permissions: Applies previously cut or copied permissions to all folders within a permission-set. - Add New all Permissions: Creates a new (blank) permission-set. (Same as clicking [+], or selecting "New Permissions" at the bottom of the form). - Delete all Permissions: Deletes the whole permission-set.
mouse to scroll within the form (to see all items), and make any changes as desired. (Your permission template name will change to 'Custom' when you start making changes.) To Give Permission to use the Wizards (Tools menu): Select "All Permissions" (and [Save] without making any changes). - Global Account Permissions: Management tasks such as editing users, schedules, holidays, etc., plus working with guard tours.
Assigning Scheduled Event Filters to Operators Management Operator Scheduled Event Filter Once the "Scheduled Event Filters" have been set up, go to the Operator screen, and ensure one is assigned to each operator, as desired. Related Topic(s): See the section on "Operators", previous. Screen Reference Pick-List (bottom of the form) - Scheduled Event Filter: This is where you select a "Scheduled Event Filter" to view or edit. This area shows the name of each filter/profile, once defined.
- On Holidays: This allows you to set how scheduled event filtering will operate on defined holidays. (Scheduled as usual, or have one of the filter 'tabs' in effect for the entire day.) Related Topic(s): Holidays and Time-Change Dates 21-0381E v4.9.
Schedules for User-Access and Area Automation Schedules Schedules are customizable time-windows for an account that can: Allow areas to 'open' (disarm), and 'close' (arm) automatically; Set times when authorized entrants will be able to enter assigned areas; Allow doors to unlock & relock, and/or change their operating criteria automatically. On defined holidays, schedules can be blocked, or customized to meet your specific needs. If custom times are desired, additional schedule(s) must be set up.
Working in the 'Grid' View In 'Grid' view, the focus is on the separate time-intervals, and the days each one is used. For each required time interval, enter the start and end time, and then select the days it will be used (tab & space-bar, or mouse-click). Tip: Times can be entered as 0010-2350 (the colon and leading zeros are inserted automatically for your convenience). Repeat this process until all required time intervals have been set up.
Grid View Schedules (Grid View) - Schedule: A reference number assigned by the system; - Name: A suitable name/description for the schedule, or its intended use; - Interval: A reference number for the unique time interval (1-6); - Start and Stop: The time that the specific time-interval begins or ends (the interval is 'active' between these times).
Holidays and Time-Change Dates Holidays (and/or time-change dates) Shared Across Multiple Accounts: Beginning with Director V4.20, groups of holidays can be set up once, and then applied to multiple accounts. For a shared holiday, changes made here will affect multiple accounts. To set up or change a 'shared holiday', refer to "Users and Holidays Shared Across Multiple Accounts".
Holiday/Daylight Savings Pick-List (bottom of the form) - Holiday/Daylight Savings (bottom of form): This is where you select a holiday to view or edit. This area shows a reference number assigned by the system, and the holiday name, once defined; Date On This Form - Name: A name or suitable description for the holiday or time-change date. (The description for holidays 1 & 2 are fixed as "Daylight Savings Time" and "Standard Time").
Authority Groups to Manage Large Numbers of Authorities (v4.6) Steps: YourAccount, Authorities, Authority Groups 1) Set up the “Authority Group” folders and This allows setting up a ‘tree’ or ‘folder’ structure for managing authorities. This feature is especially useful if you have a lot of Authorities, or can simply be ignored if you don’t. This feature uses forms view only (grid view does not apply).
YourAccount, Authorities and YourAccount, Users If you have an authority group tree/structure set up, it will be available to the Authority screen (when assigning an Authority Group), and the Users screen (when selecting the “Master Authority” on the Standard tab, or “Authority Plus” on the Validation tab). Simply click on the “+” or “-“ to the left of a desired Authority Group folder to view or hide each folder’s contents, and make your selection. 142 Verex Director V4.9.1 User's Guide 21-0381E v4.
Authorities for Users/Entrants (V4.4) Attention: Beginning with V4.4, area selection has been redesigned, and clicking an area in the tiny leftmost column causes settings to be copied to match the area(s) already selected. See "Selecting Areas" before you proceed. Users Shared Across Multiple Accounts: Beginning with Director V4.20, groups of users can be set up once, and then applied to multiple accounts.
deleted. (Go to the Users screen, select grid view, and check for the specific authority.) Related Topic: "Users (Entrants / Panel Users)". Working in Grid View: Here, grid view is for viewing purposes only. You can: Use the scroll bar at the bottom to view additional items; Click a column heading to sort on that column; Click again to reverse the sort-order.
st Details: Right-click the 1 one (a blank area above the 'tabs' in 'Forms' view), and select Copy. Then, select a blank/new authority from the list (or other desired authority), right-click near the top as before, and select Paste. After 'pasting', change the name and any settings as desired. Authorities (for users) Screen Reference Pick-List (bottom of the Form) - Authority: This is where you select a userauthority to view or edit.
------------------------------------------------------- Intrusion - Silence Alarm: Acknowledging an alarm at a panel. - Status: View status for the system and points in the area(s); - History: View the event history for the applicable area(s); - Service Test: When a user with this authority views the system status at an LCD keypad, they can use the “Verify User” option to clear alarms.
settings), 'cards locked-out', APB (if NOT set for strict enforcement), readers in 'dual-custody' or 'escort' mode (and allows the person to act as an escort). Items NOT Overridden: 'Wrong area or floor', card/PIN mode, 'strict APB', door 'interlock' issues, and 'disarm' authorities. - Escort: Whether or not users assigned to this authority will be considered as "Escorts" (for use with "Escort-Required Visitors" (to follow), and the "Escort" reader mode for doors in the selected areas).
- Door Commands: Determines if and when associated users will be able to command doors in applicable areas through LCD-keypads or this software. Elevators/Lifts and Floors: This selection applies to elevator (lift) and floor control as well (if applicable). - Door Class A/B/C Schedule: Determines if and when applicable users will be able to enter at readers set to allow access for any of these door classes during certain times. Door class restrictions can also be customized for individual readers.
Custom Information Categories for Users (Custom User Information) Users Shared Across Multiple Accounts: To implement shared 'custom-user-fields', these fields must be defined with the same usage and order for all applicable accounts, and they must be set as 'single-line edit' fields. Related Topic: "Set up any Custom User Fields for Shared Users". Custom User Fields Custom user-fields allow creating up to 20 additional categories for users (e.g., Department, Position, etc.).
Users Custom Fields Screen Reference Field 1, 2, 3, ...20 (Select the tab for the new/desired field) - Field Type: The type of new field to appear at the bottom of the User screen. (Make your selection from the list.); Note: Reports cannot be filtered on multi-line fields. Be sure to make your selection with this in mind. - Field Name: The name to appear next to the field on the User screen (such as "Position", "Department", etc.
Users (Entrants / Panel Users) Users Shared Across Multiple Accounts: Beginning with Director V4.20, groups of users can be set up once, and then given access to multiple accounts. For a shared user, changes made here will affect multiple accounts. To set up shared users, refer to "Users and Holidays Shared Across Multiple Accounts". Data Conflicts--Users: Changes made through the software will take precedence over changes for the same user entered through a keypad. V4.
in the 'tree', and locate and double-click the desired account. Tip: The Grid / Form toolbar-button allows selecting your preferred view-mode. Things You Can Do Add a New User: Click [+] at the bottom of the form, or right-click the form and select Add New from the pop-up menu. View/Change an Existing One: Select one from the pop-up list at the bottom of the form. Search for a User: Click the 'binoculars' symbol to open the ‘Find’ screen.
Users (Grid View / User-List) Pick-List (bottom of the Form) - User: This is where you select a user to view or edit. This area shows a reference number (ID) assigned by the system, and the user's name, once defined; The user ID number is required to gain access at a system keypad, and to use any "status & control" features of this software. (The user's PIN number is also required. See "Change PIN", to follow.); Filtering and Sorting: Beginning with V4.
user to perform tasks at a system keypad, and/or enter at a controlled door (4 or 5 digits). The last two digits of each PIN must be different numbers. (This allows users to indicate they are being forced to enter at a reader, or login at a keypad (i.e., duress) by reversing the last two digits of their PIN.) To Block a Visitor from Using LCD Keypads: Leave their PIN blank. User PINs pertaining to a single suite-security keypad must be unique (different).
- Type: This sets the basic type (i.e., validation method) for card. No User Access: The card/token and user PIN will be unusable. Pending Enrolment: The card/token and user PIN will be unusable until the card is accepted at a reader that is set for "Card Enrolment". Related Settings: Account Information, Setup, Card Action (Ignore Pending Enrolment). See: Account-Wide Panel Settings. Configuration, Doors, In Reader, [Card Action]. See: Reader 1 & 2 Settings for a Door.
The Photo-Badging Option With the photo-badging feature, personnel photos (and signatures) can be captured and included on the screen for each user. Selections are also provided for printing photos and other information on cards, as well as designing the layout for the information and graphics to appear on sets of cards. The ability to capture or link images is a standard feature, while designing and printing cards is optional-subject to your software licensing.
Standard Photo-Badging Selections Right-Hand side of the User Form - (person's photo-image): The captured image of the specific person (this can be captured directly, or linked from a file); - (person's signature-image): The person's captured signature image (this can be captured directly, or linked from a file); - [1st button] (face symbol): This opens a form with a number of selections for capturing user photos and/or signatures; Printer, and Tools buttons: See "Optional Features..." to follow/below.
When You Click the 1st Button (face symbol) Image - Current Capture Device: This shows your presently-selected image-capture device (or "load image from file"); - (image area): This shows your tentativelyselected user photo; - [Select Capture Profile]: This allows selecting a different image capture device (or "load image from file"); - [Capture Image]: This allows capturing the person's photo, or linking to an image file (e.g.
Right-Hand side of the User Form Optional Features (Photo-Badging Option) Printing a Card (Requires the Photo-Badging Option) Find the user form for the specific person as described previously/above; Ensure the displayed image and other settings are correct; Click [Print Badge] (printer symbol) -bottom-right portion of the user screen. Then, locate and doubleclick your previously saved card design template (.gdr file).
Number' without the asterisks. Magstripe Encoding (card-access vs. other uses): 1) Refer to [Card Printer Encoder Setup], previous/above; 2) Go to Edit Card Encoding; 3) Select the 'track' (Track 2 is typical/common); 4) Select the desired item: For magstripe access cards: *Card Number* (with asterisks); For other uses: Desired item (e.g., 'Card Number'); 5) [Add Field], [OK]. Card-Badging Update for Language Support (v4.
Things You Can Do Cards that Have Been Lost Attention: Cards can also be set as lost in the screen for the specific user. That approach is typically preferred since the user data will be transferred to here automatically (incl. user name and ID), and a card number cannot be added here while still assigned to a user.
Users Lost Cards Screen Reference On This Form - Lost Card Numbers: The area on the left of the form shows a list of cards that have been identified as being 'lost'. Tips: User names and IDs will be included in the list only for cards that were identified as lost through the "Users" screen. To sort the list by card number, user name, etc., click the desired column heading. If sorting by card numbers, notice that any leading zeros are dropped.
Fall-Back Users (Can Enter During Comms Failure) Fall-Back Users for a Panel At each panel, various card-access modes are supported for use in the event of a communications failure (i.e. a door or elevator controller module being unable to communicate with the system panel). This feature (door fallback mode), includes a selection for letting up to 10 specific users gain entry during the 'comms failure'. These users are known as "Fall-Back Users".
Viewing or Assigning Fallback Users Configuration Fallback Users How to Get Here Multi-Account Systems: First select [Account Folders] in the 'tree', and locate and double-click the desired account. MyTools Bar: Fallback Users In the Tree: Configuration (click the "+"), Fallback Users (Under the specific panel group and panel--if listed in the 'tree'.) Related Topic: "Other Desktop Choices" Tip: The Grid / Form toolbar-button allows selecting your preferred view-mode.
System Maintenance Tasks Password and Personal ID Number (PIN) Issues Default Password Default Service PIN This software includes a default operator password that should be changed right away to ensure only authorized persons will be able to access the system. Default Operator Name & Password: Operator, 1234 Similarly, each account will have a default service PIN that allows a service technician to perform various tasks through a system keypad.
The File Menu Screen Reference - Password: The desired/new password for the operator. - Re-enter Password: Enter the new password again (this helps protect against typing errors). - [Ok]: Confirms (sets) the new password. - [Cancel]: Aborts the passwordchange (keeps the previous one). File Change Password Be sure to select a password that will be easy for you to remember. Tip: Be sure to stress the importance of keeping passwords a secret to all operators.
Large Systems--Checking for Software vs. Panel Differences / Conflicts transferring or synchronizing data, refer to "Panel Communications and Updates". Differences between the Database and Individual Panels Especially with large systems that may communicate infrequently with the individual sites, panels can become out of sync with the software database as time goes on. Checking for Database Conflicts To check for database vs. panel conflicts, open the Tools menu, and select Check Database for Conflicts.
Screen Reference This screen shows a list of conflicts between the software database, and settings stored at the individual sites/panels. - Form name, Account ID: Listed items pertain to the topic/form that contains a conflict, and the ID number of the specific account (NOT the item/user ID). Tools (Menu) Check Database for Conflicts Panel vs. software conflicts should be corrected before you proceed with any additional database maintenance steps. 168 Verex Director V4.9.1 User's Guide 21-0381E v4.9.
Client/Server Systems: Checking to See Who Else is Logged onto the Database To check/repair the system database, all Tools (Menu) Who Is Logged In 'copies' of the VEREX Director software, and panel communications software must be shut down (i.e., on all VEREX Director PCs). You can check to see if any other operators are presently logged onto the central database by opening the Tools menu, and selecting Who is Logged In).
Checking / Repairing the VEREX Director Database Tables The Database Check/Repair Utility In the event of power failure, or improper shut down, etc., the VEREX Director database can become damaged, resulting in unusual or cryptic error messages. The database table repair utility provided with VEREX Director can check the database for errors, and can usually correct any problems that it finds. As well, this utility compresses the database so it takes up less space.
VEREX Director-Repair.exe Repair Database Screen Reference Database Repair - [Repair Database]: Click here to check/repair (and compress) the VEREX Director database file. Client-Server Systems: In a client-server VEREX Director system, this utility is available only at the server PC, and all associated copies of the VEREX Director software must be shut down to repair or restore the database. (To check if anyone else is connected to the database, refer to the preceding topic / above.
Backing up or Restoring the Database Database 'Backups' Preparation Steps Backing up the database means making a copy to protect against data loss or corruption due to hard drive failure, power loss, etc. Before making a 'backup' copy of the database, you should typically: 1) Ensure the software database and panels are in-sync. (for details, refer to "Panel Communications and Updates", and/or a preceding section on checking for panel differences).
Management Database Maintenance Backup Making a Database 'Backup' Using the Director Software Go to the desired workstation, and 'login' to the VEREX Director software. To access the database 'backup' feature: Select Database Maintenance from your MyTools bar, or; Click [Management] in the tree, and select Database Maintenance. On the "Backup" tab, ensure the "Backup Folder" and "Number of Backups to Keep" values are set as desired. For details, refer to the item-descriptions for this screen.
VEREX Director-Repair.exe Backup/Restore [ Backup Database ] Making a Database 'Backup' Using the Table Repair Utility With software V3.30, you can perform a backup using the Database Repair utility on your VEREX Director workstation (server PC if clientserver). Attention: The "Backup Folder" and "# of days to Keep" values must be set through the Director software. To view or change these settings, refer the preceding topic.
separately. Related Topics: Advanced Database Features Beginning with Director V4.5, you can set backups to occur automatically at a scheduled Setting Backups to Occur Automatically (Scheduled Backups) v4.5 time. Be sure to first do at least one backup manually to ensure there are no issues with the target folder, etc. Attention: The "Backup Folder" and "# of days to Keep" values must be set through the Director software.
Automatic Backup Management Database Maintenance Backup - Enable Automatic Backup: Select this to allow setting backups to occur automatically. Note: This will not be available until you select/enter a backup folder. - Frequency (days): This sets how often scheduled backups will occur (i.e., once every X days—per your selection). - Start Time: This sets the starting time for the scheduled backup. - Next Start Date: This sets the date for the first/next occurrence of the scheduled backup.
Reverting to (Restoring) a Backup Copy of the VEREX Director Database 2) If the VEREX Director database becomes corrupted (such as due to lightning or power failure), or lost (such as due to hard drive failure), you can revert to a copy that was created previously using the 'backup' feature. In a client-server VEREX Director system, the database restore feature is available only through the server PC. 3) reliable state.
VEREX Director-Repair.exe Backup/Restore [ Restore Database ] Screen Reference - [File]: Click here to locate and select your desired 'backup' file (i.e., a BAK file that was created previously). Tip: Double-click the file, or select the file and click [Open]. - [Restore Database]: Click here to revert to your selected database file. (You'll be informed when the restoral is finished.
Exporting or Importing Activity or Audit Logs (Archive) What is Archiving? Archiving Messages (Import or Export) The archive feature allows moving message logs out of the main database (to improve performance), or re-importing them for use with activity and audit reports. To access the 'Archive' screen: Read Me: Archiving or purging on a regular basis is highly recommended since the system can become slow and/or unstable if database files become very large.
Management Database Maintenance Archive Screen Reference - [Archive Folder]: This is the location where the archived data will be stored. Client-server Notice: In a client-server VEREX Director system, the archiving actually occurs at the VEREX Director server PC. As such, the location entered here must be as if you were sitting at that PC. Director-Server PC: This is the PC that includes "...Director-Server.exe".
Removing old Activity or Audit Logs (Purge) What is Purging? "Purging" refers to deleting old records from the message logs, to free up additional harddrive space, and allow reports to run faster. Management Database Maintenance Purge Read Me: Archiving or purging on a regular basis is highly recommended since the system can become slow and/or unstable if database files become very large. Purging can be done manually, and can also be set to occur automatically.
Operating System Maintenance The Microsoft Windows operating system has been in development and general use for many years. Microsoft is finding existing 'issues', and releasing "Service Packs" or other types of updates on an on-going basis to ensure Windows users have a more-or-less trouble-free experience. It is important to keep your Windows operating system up-to-date in this regard.
21-0381E v4.9.
System Configuration Beginning with V4.0 VEREX Director, you can use the Configuration Wizard to set up a new system. For more information, refer to "New Installation? Try the Wizard!". 184 Verex Director V4.9.1 User's Guide 21-0381E v4.9.
Working with Accounts and Folders (Multi-Account Systems) Account Folders, and account-selection issues pertain only for systems with multi-account licensing (or operators with the authority to edit account folders). Beginning with V4.0 VEREX Director, you can use the Configuration Wizard to set up a new system. For more information, refer to "New Installation? Try the Wizard!". Visual Quick-Start You can view accounts folder-by-folder, or sort a full listing by name, address, etc.
menu when you are 'in' the Account Folders portion of the tree. Opening an Account, or Switching to a Different Account (for Monitoring, Status & Control, User Admin., etc.) Click [Account Folders] in the 'tree'. Then, browse through any account folders, and double-click the desired account (either in the tree, or the centre portion of the screen). Multi-Server Alternative: For a multi-server login, you can also view and select accounts under [server] in the 'tree'.
'grid' view, and scroll through the operator list, checking the "Account" and "Monitor Account" columns for the specific one. Be sure to reset any as needed as you go along (click [...] ). Note: To allow deleting an account folder, you must ensure that it is not assigned within any operatorpermissions screens. See: Operator Permissions ------------------------- Then, click [Account Folders] in the 'tree', and locate your desired account (or folder).
(to follow/below). [Server] (if multi-server login) Screen Reference Account Folders: Account folders are not shown in this screen. (Double-click a server to access its account folders.) Operator Permissions: Each operator will be able to view only the accounts associated with their assigned folders. Related Topic(s): Operator Permissions Show all Accounts under This Node: This selection applies only to account folders (it is not needed in the [Server] portion of the 'tree').
Right-Click the Account List Sort Advanced Sorting In addition to sorting on a single column heading, the account list can be sorted on multiple items as desired (e.g., by City, then account name, etc.). Steps: 1) 2) 3) Go to the desired 'node' under [Account Folders] in the 'tree' (or [Server] if logged into multiple servers). Right-click within the account list, and select "Sort" from the pop-up menu. Refer to the item-descriptions for this screen while making your selections.
Users and Holidays Shared Across Multiple Accounts Note: Suite-security keypads and "Communities" (Shared Users) are not supported at the same time. Introduction Beginning with Director V4.2, you can set up users and/or holidays to apply to multiple accounts. Once set up, changes can be made to a shared user or holiday within a specific account, and the changes will be copied to other applicable accounts automatically.
Phase 1: Account-Specific Data Account Folders Account Name Users Custom Fields 1A: Misc. Account Settings Feature Set: "Shared Users" are supported only for specific panel "Feature Set" values: Beginning with V4.7: Feature set 2 or higher. Director V4.2 - 4.6x: Feature-set 2, 3, or 4. To enable the required screens, go into the "Account Information" screen for each account, and change the "Feature Set" value if needed (also see the "Technical Notes").
1C: Ensure Authorities Have Been Set up for Each Account Account Folders Account Name Authorities In Phase 2, groups of authority ID#s will be reserved for use with shared users (5 at a time). Due to differences in areas, and security requirements, the authorities themselves must be set up at each account as usual (at the same authority ID# for each account). Be sure to keep track of the authority ID# range to ensure the correct ones are reserved in Phase 2.
[Management] Community Groups Communities Phase 2: Community Groups 2A: Set Up Communities With shared users, the 'PIN Mode' and 'User Logon Mode' for each account is set under "[Management] Community Groups", and will not be editable under "Account Information". (This is required since the length of each user's PIN and card number is fixed.) These are defined as "Communities" which will be assigned in step 2B.
plus the 'PIN Mode' and 'User Logon [Management] Community Groups Users Mode' for the accounts to be associated with these users. This includes reserving ranges of user ID#s for groups of shared users. Tip: This is done in blocks of ten (whether they all will be defined or not). Note: For multiple groups of shared users to apply to the same account, ensure the ID ranges do not overlap.
[Management] Community Groups Holidays 2C: Reserve Holiday ID#s (Shared Holiday Groups) Holidays (and time-change dates) can be shared across multiple accounts if desired. This includes reserving ranges of holiday ID#s for use with each group of shared holidays. This is done in blocks of three or more. Note: Holiday #1 & #2 are reserved for the dates to switch between Daylight Savings and Standard Time.
Phase 3: Shared Users and Holidays 3A: Setting up Shared Users Account Folders Shared Groups Shared Users Once the related "Community Groups" have been set up (previous/above), you can set up shared users the same as for individual accounts, with the following exceptions: Shared users are initially defined under "[ Account Folders ] Shared Groups"; (NOT under "Users" for a specific account.) Shared users are grouped in the tree by their "Shared User Group" (defined previously); (e.g.
3B: Setting up Shared Holidays (and/or Time-Change Dates) Account Folders Shared Groups Shared Holiday Once the related "Community Groups" have been set up (previous/above), you can set up shared holidays the same as for individual accounts, with the following exceptions: Shared holidays are initially defined under "[ Account Folders ] Shared Groups"; The Shared Holiday screen is identical to the Holiday/Daylight Savings screen.
Phase 4: Assign Shared Items to Accounts 4A: Assign Groups of Shared Users to Accounts (Shared User Management) Account Folders AccountName Account Information, Shared Users Once the related "Community Groups" have been set up (previous/above), groups of shared users can be assigned to applicable accounts. Notes: Only 'Shared User Groups' with nonoverlapping ID# ranges can be selected for any specific account.
Account Folders AccountName Account Information Shared Holidays 4B: Assign Groups of Shared Holidays to Accounts (Shared Holiday Management) Once the related "Shared Holiday Groups" and "Shared Holidays" have been set up (previous/above), groups of shared holidays can be assigned to applicable accounts. Notes: Only 'Shared Holiday Groups' with non-overlapping ID# ranges can be selected for any specific account.
Account-Wide Panel Settings (Feature-Set, Service PIN, etc.) Account Information: (technical Account Information settings) These screens allow setting the site/account name (to appear in the 'tree'), plus various technical systemwide parameters. These include the "Feature Set", which determines the system capacities for the account. "Account-type" selections determine the items (fields) to appear on-screen.
Feature Set Information - Panel Version: Set this to match the actual panel (firmware) revision level for panels associated with this account (all panels for each account must be at the same firmware revision level). Notes: With VEREX Director v4.4, panel firmware versions to be supported within an account is set through the new account wizard. If the panel version is set incorrectly, you will be unable to communicate with the panel(s).
[Management], Community Groups, Communities. (See the previous topic on "Community Groups"). - User Logon Mode: This determines whether users must enter their ID number or card number when logging onto LCD keypads, and/or gaining entry at doors (e.g., ID + PIN mode). User-number selections include the number of digits--which should be set to support the largest card number used at the site.
Invalid Cards: Cards denied access due to: Not in database; Wrong site number; Wrong version number; High Risk: Cards denied access due to: Card expired; Schedule expired; Interlock violation; Reader locked out; Wrong area.
Event Responses for Acknowledging Alarms Event responses Sample event responses can be set up ahead Account Information Event Response of time to make things easier for operators when they are acknowledging alarms. Related Topic: "Dealing with Alarms (Comment / Resolve)".
Alarm / Event Instructions Introducing Event Instructions Event instructions are text Account Information Event Instruction instructions that can be set to appear in the comment/resolution window when an operator is acknowledging an alarm (pertaining to specific types of messages, or those from a specific sensor / input-point).
Management Sound Enabling Sounds (to be associated with event/alarm messages) Sounds to be Associated with Specific Events and Alarms Sounds can be associated with specific alarms and events. Before a custom sound can be associated with an event, it must be activated here. Note: By default, your PC's "exclamation" sound will be associated with alarms that require resolution. This is set through the Windows control-panel.
rename, or associate with a different WAV file. This area shows a reference number assigned by the system, and the name of the sound, once defined; On This Form - Name: A suitable name for the sound (e.g., "Fire Alert"); - File: This is the location (path) and filename of the sound file (.WAV). Tip: Click [...] to browse for the file, Then, select the file and click [Open]. - [ ]: Select this to listen to a sample of your selected sound. 21-0381E v4.9.
Customizing How Events are Displayed (Event Priority) Account Information Event Priority Introducing Event Priorities You can customize how specific events and alarms will be displayed, and assign custom colors, and sounds. These selections can be system-wide, or for events occurring in a specific area. Now, refer to the selection-descriptions for this screen while viewing or entering your desired settings. Tip: This feature uses a special view style (the Grid / Form button will be disabled).
only; Buttons at the Bottom of the Form - [Add]: When viewing custom events (i.e., "By Area"), this creates a blank 'row' to allow setting up a new custom event; - [Delete]: This allows deleting a custom event (when viewing "By Area"); - [Customize for Area]: When viewing "System Wide" events, this allows quickly creating a custom (area-specific) version of a selected event; Ref: [Management] Sound Enabling Sounds (to be associated with event/alarm messages).
Detailed Operator and User Audit Trail (V4.6) "Detailed auditing" records changes made to operators and users. When you enable this feature, the “before” and “after” details for changes will be logged, available to the archive and purge functions, and available through Audit Reports. Exception: Changes made through a keypad will show ID numbers only rather than full names. [Management], Reporting To enable this feature, go to: “[Management], Reporting”, and select “Record Detailed Logs” ().
Setting up Video Events (V4.5) About Video Events Video events are specific events pertaining to input points and doors that have been associated with recordings from one or two specific camera(s). These appear with a camera symbol on the left in the event monitoring window. DVR Types: Supported video servers include: NetVision (V2.1 or V2.2 and newer) Yes (via "Visual Director") password that has been given the authority to play videos from the specific camera(s).
Software-Based Text Paging (Serial Reporting) v4.4 About Serial Reporting Setting up Serial Reporting In addition to the numeric paging that is supported through the main panels, the serial reporting feature allows selected alarm/event messages to be transmitted to an alphanumeric pager. This is done through a serial paging interface that includes software for configuring its communication parameters, and pager phone number, etc.
Screen Reference [Management] Serial Reporting On This Screen - Enable Serial Reporting: This activates the serial reporting feature; - Serial Port: This sets the serial communications port to be used for serial reporting (typically COM1); - Baud Rate: This sets the transmission speed for alarm messages transmitted via serial reporting (e.g., 9600). - Field Delimiter: This sets the character to be inserted between the segments of each message (e.g., user name, door name, etc.).
Panels, Panel Groups, and Connection Settings Beginning with V4.0 VEREX Director, you can use the Configuration Wizard to set up a new system. For details, refer to "New Installation? Try the Wizard!" Panel Groups and Connection Settings Panel Groups Pertain to individual panels, or groups of panels sharing a connection (up to 30 panels per group/connection). Tip: Each connection pertains to a physical cable, or a dial-up modem and phone number. IP Exception: With IP connections ( V3.
When You Select a Panel Group (under Configuration) Location Settings pertaining to the location of the panel(s), plus the local time zone for the specific location. Tip: The Time Zone setting causes any panel clock updates to be adjusted accordingly. Connection These settings pertain to panel communications sessions that are initiated by the software. Quick Tip: "Logical tree View" must not be in effect.
System Panels and Displayed Item-Numbers Beginning with V4.0 VEREX Director, you can use the Configuration Wizard to set up a new system. For details, refer to "New Installation? Try the Wizard!" System Panels Things You Can Do Add a New Panel: Under Configuration in the 'tree', locate and right-click the panelgroup for the new panel, and select Add Panel.
When You Select a Panel (under Configuration) - Location: A suitable name or location for the specific system main panel; - Display Offsets (Repeating vs. Unique Item-Numbers): With the default setting of "1", the areas, doors, etc. for each panel will be numbered the same (e.g., 1st Panel, Area 1, 2, 3,… 2nd Panel, Area 1, 2, 3,… etc.). This allows for accounts that span multiple buildings. Setting the 'offsets' allows item-numbers to be unique / sequential (e.g., Area 1, 2, 3, ...17, 18, etc.
System Settings for each Panel (V4.4) General System Settings for a Panel The System (General) Screen Configuration, System, (Standard ) The System screen provides access to various security settings pertaining to a specific panel. How to Get Here Multi-Account Systems: First select [Account Folders] in the 'tree', and locate and double-click the desired account.
occur, the siren time must be greater than 30 seconds. The Siren Feature: This pertains to monitored sensors (input points), system/equipment conditions, and/or panic/emergency keys that have been set to trigger a siren condition—as signalled by a programmable output set to activate on a system or area "siren" condition. Related Topics: Equipment Settings (Pseudo / Internal Inputs) Input Points—Monitored Sensors. Tip: "Emergency keys" pertains to 1st 3 inputs on an LCD keypad.
STU and VBUS outputs--plus the two on the panel itself for a grand total. This is selectable as multiples of 4 only (4, 8, 12, etc), so select the next higher value if necessary. Attention: VBUS and STU outputs will NOT be recognized if the panel onboard outputs value does not account for all of these outputs as described here. Intrusion Settings for a Panel (V4.4) The System Intrusion screen This screen provides access to various intrusion settings that pertain to a specific panel.
Configuration, System, Intrusion Screen Reference Pick-List (bottom of the form) - Panel: If the tree is not set to show items on a panel-by-panel basis, you will be able to select a panel here (for systems that have more than one). A "Panel Group" reference may also be shown here, or you can set the 'tree' to list configuration topics separately for each panel. For more information, refer to "Other Desktop Choices". ACPO Note: This tab appears only for panels set for UK (ACPO) operating mode.
Monitoring, Numeric Paging, & Remote Mgt. Settings The System Communication screen This screen provides access to monitoring, numeric paging, and communications settings for a specific panel. Tip: Beginning with VEREX Director V4.0, you can use Wizards to set up a new system, and initiate communications with panels. (Look in the Tools menu). How to Get Here Multi-Account Systems: First select [Account Folders] in the 'tree', and locate and double-click the desired account.
another PC running the VEREX Director Screen Reference Pick-List (bottom of the form) Configuration System Communication -Panel: If the tree is not set to show items on a panel-by-panel basis, you will be able to select a panel here (for systems that have more than one). A "Panel Group" reference may also be shown here, or you can set the 'tree' to list configuration topics separately for each panel. For more information, refer to "Other Desktop Choices".
Exception: For a Bell 103 connection (small systems, max. 300 users), the reporting mode is not supported. Tip: Reporting to a central monitoring facility is set through SIA/CID or SIP/HSC (to follow / below). - Interface IP Address and Interface IP Port (IP connections only): These settings pertain to an IP (LAN/WAN) or secure/encrypted IP connection to a panel. Tip: This can be an IP address, or a name (FQDN). Contact your IT rep. for assistance if needed.
Director CD). (HSC): An HSC connection requires a high-security communications module, and Mark-7 / DVACS service (Canada). HSC modules require some set-up locally through an LCD keypad (for details, refer to the commissioning or hardware guide for your system). SIA / CID Test - Frequency (and Time/Day Settings): The length of time between (and time of occurrence for) automated trials on the reporting channels (HSC and/or dialler--as per the "Report Mode" above).
Paging (Signal a Numeric Pager) UK/ACPO: This feature is not supported with UK/ACPO operation. - Paging Mode: Future Use. This allows enabling or disabling numeric paging, and selecting the format/protocol to be used. None: Numeric paging disabled. Numeric semadigit w/handshake: North America with handshaking. Blind SemaDigit: North America without handshaking. SemaPhone: Common for Europe.
Pick-List (bottom of the form) Configuration System Access -Panel (optional): If the tree is not set to show items on a panel-by-panel basis, you will be able to select a panel here (for systems that have more than one). A "Panel Group" reference may also be shown here, or you can set the 'tree' to list configuration topics separately for each panel. For more information, refer to "Other Desktop Choices".
'checksum' (1-40); - Start: The starting position of the data being checked for odd-parity (1-40); - Length: The number of digits being checked for odd-parity (1-40). Even Parity These settings pertain to even-parity checking, which helps to identify card 'misreads'. - Position: The position of the even-parity 'checksum' (1-40); - Start: The starting position of the data being checked for even-parity (1-40); - Length: The number of digits being checked for even-parity (1-40).
Equipment Settings (Pseudo / Internal Inputs) Equipment Settings for a Panel The Equipment screen includes monitoring / signalling settings pertaining to various events associated with a specific panel (and/or expansion modules). These can also be thought of as 'pseudo' or 'internal' input points. How to Get Here Multi-Account Systems: First select [Account Folders] in the 'tree', and locate and double-click the desired account.
Configuration System Equipment Screen Reference Pick-Lists (bottom of the form) -Panel Group & Panel references (optional): This is where you select a specific panel-group and panel in a multi-panel system where the 'tree' is not set to show items on a panel-by-panel basis. For more information on this feature, refer to "Other Desktop Choices". - Equipment: This is where you select an internally monitored item to view or edit.
Areas and Related Settings If you change any value for an area, this will cause that area to be reset to its default / scheduled state and arming level (this allows configuration updates to be managed properly). To check or re-set status aspects, refer to the "Area" status/control topic. Areas and Related Settings Areas allow setting up monitoring and operating characteristics for all sensors and/or readers in a common location (associated with a specific panel).
Pick-Lists (bottom of the Form) Configuration Areas -Panel Group & Panel references (optional): This is where you select a specific panel-group and panel in a multi-panel system where the 'tree' is not set to show items on a panel-by-panel basis. For more information on this feature, refer to "Other Desktop Choices". - Area: This is where you select an area to view or edit.
easily determine if others are still present. For a larger site, area scheduling is recommended (see "Scheduling", to follow/below). - Extend Delay on Fail to Exit (V4.4): In the event of a "Fail to Exit" (as per the "Fail to Exit Mode", previous/above), the exit delay will be extended by two minutes. Exit Confirmation Button: This will also cause "Fail-toExit-Mode selections" that indicate an 'exit button' to log an event if the button is not pressed before the original exit delay expires.
Access (systems with access-controlled doors) - Auto Disarm on Valid Token (V4.3): The area will automatically disarm when a person with disarm authority (Off or Stay as applicable) is granted entry to this area. This feature can be customized for groups of users as per their assigned authorities. Details: YourAccount, Authorities, (Area Attributes), Access Schedule Authorities for Users/Entrants V4.4: With Director V4.
'emergency off' is performed (i.e., being disarmed outside of the schedule). This limits the time that an "Emergency Off" can remain in effect. - Work Late Input: When someone presses a work-late button in this area (during the 'pre-arm cycle), the scheduled closing time with be set as {value selected here} from the present time. Note: A worklate button is a custom input point with its 'pre-process' set as "Worklate".
Counting ( V4.20) These selections pertain to monitoring the number of people (or vehicles, etc.) in an area at any one time (per access-granted), and whether or not the area can be armed with persons still listed as being in the area. User Counter - Maximum: (0 - 16383) The maximum number of users/vehicles allowed in an area before its status will be "full". Tip: This can be used to trigger an output (e.g., "Parking Lot Full" sign).
Auto Arm Steps 1) 2) 3) ( V4.20) These settings allow having an area arm automatically: When a/the door closes; When there is 'No Activity', and/or; When no one is present (user-count 'minimum'). Auto-arming based on 'activity' and 'usercount' can also be tied to the arm/disarm schedule for each area. Define a "Custom Point Type", being sure to select: "Preprocess: Activity Monitor", and other settings as desired. Locator: Configuration, Custom Point Types.
programmable hot-keys 6-9 & 0 will require a user with "Function Key" authority to be logged in. (Function keys 1-5 do not require ID/PIN entry, except at a portable/wireless arming keypad). Tip: This setting is recommended to help protect against false alarms. For details on using the function keys on a system LCD keypad, refer to the xL (panel/keypad) User's Guide. What each function key does is set up under "Programmable Outputs".
Area Groups (V4.4) and Multi-panel Arm/Disarm Setting up Area Groups (V4.5) Configuration, Areas, Area Group About Area Groups Area groups provide an easy way to arm and disarm named groups of areas through an LCD keypad. You can define up to 16 of these area groups. Area groups of the same name can be armed (On) and disarmed (Off) across multiple panels through a keypad connected to any one of the panels. (Details appear at the end of this topic.
Panels can be hardwired together, or Setting up Multi-Panel Arm/Disarm (V4.5) this can be 1 - 12 letters (all caps) and/or numbers. Area groups of the same name can be armed (On) and disarmed (Off) across multiple panels through a keypad connected to any one of the panels. This will apply only to areas for which the specific user has the required authority.
Expansion Modules Expansion Modules and Related Settings Things You Can Do Expansion modules are devices that provide support for additional inputs, outputs, and/or special features. Some examples include: System LCD keypads (different types—some with built-in reader); Door Controllers (typically supporting 2 doors / 4 readers); Elevator / Lift Controller (2 cabs, with one reader per cab; max.
Configuration Modules Screen Reference Pick-Lists (bottom of the Form) -Panel Group & Panel references (optional): This is where you select a specific panel-group and panel in a multi-panel system where the 'tree' is not set to show items on a panel-by-panel basis. For more information on this feature, refer to "Other Desktop Choices". - Module: This is where you select a module to view or edit.
Keypad (settings for LCD Keypads) - Assigned to Area: The 'area' that this keypad is associated with; - Exit Delay When Arming: Whether or not an exit delay is to be in effect when arming the keypad's area to 'Stay' and/or 'On'. (Arming any other areas from this keypad will be immediate). 'Stay' pertains to 'perimeter' sensors being monitored, and 'On' pertains to all sensors in the area being monitored.
duration you must wait after presenting (and removing) the card/token each time to be treated as a double or triple badging. - Triple badge mode: If selected () this feature requires a triple-badging, versus only a doublebadging if not selected. Note: All other fields and available selections are the same as for badge-hold mode as supported beginning with Director v4.4. Access (V4.4) Access Mode - Access Control: This identifies that the reader is to be associated with an access-controlled door.
Suite-Security Keypads and Related Settings If you change any value for a suite-security keypad, this will cause that unit to be reset to its default / scheduled state and arming level (this allows configuration updates to be managed properly). As such, configuration changes to active units should be done only by arrangement with the occupant.
Then, issue a "Send to Panel" Configuration Suite Security communications session to transfer all settings to the associated panel. For details, refer to "Panel Communications and Updates". Screen Reference Pick-Lists (bottom of the Form) -Panel Group & Panel references (optional): This is where you select a specific panelgroup and panel in a multi-panel system where the 'tree' is not set to show items on a panel-by-panel basis. For more information on this feature, refer to "Other Desktop Choices".
authorized entrant to disarm the suite-security system; - Exit delay: The duration that the monitoring of 'Exit' points will be held/delayed to allow the user to exit after arming the keypad. - Extended Point Delay: The duration that the monitoring of 'Extended-Delay' points will be held/delayed to allow an authorized entrant to disarm the keypad. - Siren Time: This sets the duration for siren activations for this suite-security keypad.
- Hold Badge Mode: Future Use. Selects an action to occur automatically (arm, disarm, etc.) when a card is accepted and 'held' in place at a reader associated with the suite/keypad. - Hold Time: Future Use. Select a duration to identify a prolonged card badging (badge-hold). (Pertains to all items regarding "hold".) - Hold Badge Requires PIN: Future Use. This sets whether or not the badge-hold feature will require the user to enter their PIN. - Display Hold Badge Prompt: Future Use.
Doors, Readers, and Related Settings If you change any value for a reader/door, this will cause that device to be reset to its default / scheduled state (this allows configuration updates to be managed properly). To check or re-set status aspects, refer to the "Door" status/control topic. Introduction to Access-Controlled Doors "Access-control" (who can go where and when) can be easily integrated into the system using door-control modules.
Configuration Doors (First Tab Shown) Pick-Lists (bottom of the form) -Panel Group & Panel references (optional): This is where you select a specific panelgroup and panel in a multi-panel system where the 'tree' is not set to show items on a panel-by-panel basis. For more information on this feature, refer to "Other Desktop Choices". - Door: This is where you select a door to view or edit.
To have the door simply re-lock at the closing time, set the "In Schedule" value as desired, and set the "Out of Schedule" value to "Locked". To have the door unlocking follow the area armingstate only, set the schedule to "None", and "In Schedule" to either "Area is Off", or "Area is Stay/Off", as desired. If you do not want the door to unlock automatically based on a schedule and/or the area arming-state, set the "Schedule" to "None", and the 'In Schedule' value to "Locked". v4.
Reader 1 & 2 Settings for a Door Defining a ‘Required Attendance’ Zone For time and attendance reporting, a ‘required attendance zone must be defined by setting the "Area" as "Outside" for all readers used to exit from this zone. See the "Area" description for more information. Note: For proper time and attendance tracking, there must be no other way to exit from the requiredattendance area (all exit doors must have a reader).
"arming station". An arming station includes a Wiegand reader with keypad, and supports additional functions for arming and disarming areas, adjusting the area closing time (worklate), etc. For details, refer to the User's Guide for your xL system (panel/LCD keypad). Note: Arming-station wiring differs from other readers (ensure the proper installation instructions have been followed).
- Unlock Door on Card Action: Whether or not the door will unlock (plus the associated 'access granted' message). Note: This setting applies only as part of a 'card action' taking place (i.e., the door always unlocks for cards simply being granted access). - Duration: This determines how long the enabled cards can be used (from the moment they are activated). End of Today (Schedule 50): This allows enabling cards for the present day only--while schedule #50 is active ("in window").
10 seconds) before it considered to be an alarm condition. Note: Door Controller (ADP) ≥ 2.5, The XL Panel & ISM ≥ 4.58g Held Open Alarm Interlock - Transmit / Sonalert / Siren: The area arming levels for which a 'Door Held Open' alarm will be transmitted, and/or cause a local sonalert or siren to be sounded. Forced Open Alarm - Transmit / Sonalert / Siren: The area arming levels for which a 'Door Forced Open' alarm will be transmitted, and/or cause a local sonalert or siren to be sounded.
The door will not relock until the 'momentary unlock' time expires. - Force Buzzer Clears on Door Closure: Future Use. - Insertion Reader: Future Use. About Video Events Video events are specific events pertaining to input points and doors that have been associated with recordings from one or two specific camera(s). These appear with a camera symbol on the left in the event monitoring window. Clicking the camera symbol allows viewing the recording for that camera at the time of the event.
Elevators (Lifts) and Associated Readers If you change any value for an elevator/lift, this will cause that device to be reset to its default / scheduled state (this allows configuration updates to be managed properly). To check or re-set status aspects, refer to the "Elevator" status/control topic. Introducing Access-Controlled Elevators With access-controlled elevators, floor callbuttons are disabled until an authorized person presents their access card.
Configuration Elevators (1st tab shown) Pick-Lists (Bottom of the Form) -Panel Group & Panel references (optional): This is where you select a specific panel-group and panel in a multi-panel system where the 'tree' is not set to show items on a panel-by-panel basis. For more information on this feature, refer to "Other Desktop Choices". - Elevator: This is where you select an elevator to view or edit.
Extended Reader - Bi-Colour LED Mode: Select this if the reader at this door has a single bi-color LED (instead of the two separate LEDs). (Elevator (Lift) Reader Settings) Note: Arming-stations are not supported in elevator cabs. - Insertion Type Reader: Ensures the access card is not read more than once when inserted and removed.
Card/PIN as well. If scheduled, different entry requirements can be selected for when the schedule is active versus outside of the chosen schedule. With "Dual Custody", two different users must present their card and/or PIN (and neither of them can be set as "Visitor--Escort Required"). When set to "Escort", a valid 'escort' can also enter on their own by presenting their card/PIN twice. If visitor cards (set to require an escort) are presented, visitor escort processing will take over (e.g.
cards/tokens accepted; Valid Site Code: All cards/tokens with the correct site code will be granted access; 10 Fall-back Users: Only the users who are assigned as 'FallBack Users'. For details, refer to "Fall-Back Users...". - Desecure on Comms Fail: Whether or not all floor call-buttons are to be enabled whenever the elevator controller or floor relay board has lost communications. - Relay Off When Desecure: This sets the normal physical state of the floor selection relays.
Floors (Pertaining to Access-Controlled Elevators / Lifts) If you change the name or other setting for a floor, this will cause that floor to be reset to its default / scheduled state (this allows configuration updates to be managed properly). To check or re-set the floor state (secure vs. desecure), refer to the "Floor" status/control topic. Access-Controlled Floors Systems with elevator controllers can include up to 124 access-controlled floors.
YourAccount Floors Screen Reference - Building Name: A suitable description for the building or complex; - Floor: The first column contains a description for each floor. (Click within the name field, and type a suitable name); To change the name for a floor, select the present name, and enter the new name. The top cell in this column does not pertain to a floor. Sort Order: To maintain proper order wherever floors are sorted by name, be sure to select names accordingly (e.g.
Input Points—Monitored Sensors Input Points and Related Settings Input points are the system’s way of monitoring devices that detect smoke, motion, door/window openings etc. in each area. The Input Point screen allows fine-tuning basic monitoring characteristics, identifying the area the sensor is in, and whether or not it is on the perimeter of that area. Input Capacity Detail: ISM (square mainboard): 128 (120 external to the main panel). All of these can be wireless if keypads are set to zero each.
Screen Reference Configuration Input Points Pick-Lists (Bottom of the Form) -Panel Group & Panel references (optional; bottom of the form): This is where you select a specific panel-group and panel in a multi-panel system where the 'tree' is not set to show items on a panelby-panel basis. For more information on this feature, refer to "Other Desktop Choices". - Input Point (bottom of form): This is where you select an input-point to view or edit.
types pertain to an individual panel. Standard - LCD Name: A shorter version of the name to be displayed at LCD keypads. This is assigned automatically, and can also be changed if desired (max. 12 chars., plain text). Command Points: For input points set as "Point Type: Custom Type: Command Point", the LCD name will be replaced with point-command data, and will not be editable. - Module: This is "Panel" (a system panel) or the module/POD associated with the specific input point number.
- Area / Door: For area and door commands, select the target item here. Command This allows a button or sensor to command an aspect or device for any (or all) panels in an account. This tab appears only if the 'Point Type' (previous/above) is a 'custom type' set as a 'command point'. Related Settings: Configuration, Custom Point Types. See: Input Points—Custom Point Type (to follow). Tip: For additional operating details, refer to "Notes / Attention" at the end of this section.
specific camera(s). These appear with a camera symbol on the left in the event monitoring window. Clicking the camera symbol allows viewing the recording for that camera at the time of the event. If a video that coincides with the event is available, it will open and start playing automatically starting at the time of the triggering event. Note: Playback for video events is NOT supported for March R4 DVRs.
Input Points—Pre-Defined Sensor Types Burglary Points: Type Arming Level Preprocess Class Entry Door Entry Route Perimeter Interior Motion FAP - Motion Day Warning 24hr Burglary Perimtr 12hr Perimeter 12hr 12hr 24hr 24hr Door (area 1) E/E Route Immed Immed FAP Immed Immed Burg Burg Burg Burg Burg Burg Burg Preprocess Class Immediate 15s delay Immediate Immediate Immediate Fire-A Fire Fire holdup Emerg Preprocess Class Immediate Battery Fail Mains Fail Spvsr Spvsr Spvsr Preprocess Class By-
Input Points—Custom Point Types Custom Input Point Types In addition to the extensive list of pre-defined point types, custom input point types can be set up to tailor input-point characteristics to meet your specific needs. Once defined, these are referred to as Point Types 80-99.
Configuration Custom Point Types Screen Reference Pick Lists (bottom of the form) -Panel Group & Panel references (optional; bottom of the form): This is where you select a specific panel-group and panel in a multi-panel system where the 'tree' is not set to show items on a panel-by-panel basis. For more information on this feature, refer to "Other Desktop Choices". - Custom Point Type (bottom of form): This is where you select a custom point-type to view or edit.
taken from the corresponding pseudo points. AC Failure and Battery trouble outputs follow these inputs. Note: The XL Panel firmware ≥ 4.58g is required. Level: The arming levels of the area assigned to the point for which the point will be fully monitored by the system. Exception: For keyswitch operation, see the previous "Keyswitch" note. Activity Monitor: The arming levels of the input point's area for which the point will be treated as an activity monitor versus a standard sensor (e.g., Burglary).
Custom Circuit-Types for Input Points (V4.4) Custom Circuit-Types Newer styles of modules support custom circuits for input points, while any older-style modules will continue to support the standard circuit-types. Tip: Suitable default values are provided here for north America, Europe, and UK-ACPO (per panel mode). The defaults typically need to be changed here only for sites that require custom/different values.
Configuration, Input Points, Custom Circuit Screen Reference Circuit 1, 2, 3, or 4 ) - Circuit Type: This allows selecting from the supported types of custom circuits; Tip: The circuit-type that you select will be shown graphically near the middle of the screen, and default resistor values are shown farther down. ------------------------- [Reset Circuit]: This reverts the present circuit number (tab) to its default value. Tip: This is the same value as with older-style modules, and V4.
Programmable Outputs (Signalling & Device-Switching) Output Points and Related Settings Output points are programmable electronic switches that can be used to signal alarms or control items such as lights, garage doors, etc. The Output Points screen allows viewing or changing the characteristics for each of these outputs. Power: Outputs provide a switching function only (devices must include a suitable power source).
Tip: The Grid / Form toolbar-button allows selecting your preferred view-mode (forms view is recommended here). Configuration Output Points Things You Can Do Add an Output Point: Click [+] at the bottom of the form, or right-click the form and select Add New from the pop-up menu. View/Change an Existing One: Select one from the pop-up list at the bottom of the form. Search for An Output Point: Click the 'binoculars' symbol. Then, enter the name and click [Find].
and add or select the desired output. Click the small [...] button to access this screen. Click an "item" (such as "unassigned") to select a new value. (Additional items will appear as you go along--where applicable). Configuration Output Points [ ... ] (Edit Output) Tip: See the "Item" descriptions, to follow. Use the Up/Down arrows to scroll in pop-up lists. Right click items to select a command (e.g., Invert, Insert, Remove).
In Window / Out of Window: Simplistic: Working hours vs. after-hours. Detail: Pertaining to during vs. outside of the active/valid times of a schedule. Pseudo: Internally-monitored conditions. (Ref: Configuration System Equipment). SIP: Reporting to a central station via IP. SNAPP: Module communications bus. Version E: This indicates conditions pertaining to European monitoring requirements.
"AND/OR"s (Boolean Operators for Multi-Condition Equations): If "This" And/Or "That" is true Choice OR This That AND NOR NAND XOR XNOR Output Will trigger: When either condition (or both) are true. Only when both are true. Only when neither one is true (i.e., both NOT true). When either one or neither of them are true, but not both. When one or the other is true, but not both. When both or neither are true, but not one or the other by itself.
Programmable Output Functions System Was In Alarm System System WAS IN ALARM. This is only for input points in alarm e.g.
System Pod Trouble System Version "E" Fire System Version "E" Personal Attack System Pseudo 11 – Module Trouble Pod Battery Low System Version "E" Unconfirmed Alarm System Version "E" Set/Unset System Pseudo 12 – Module Battery Low Pod Program Edit System Version "E" Freezer/Fire Fault System Pseudo 13 – Module Program Edit Pod Program Error System Version "E" Bypass in Effect System Version "E" Confirmed Alarm System Pseudo 14 – Module Program Error Miscellaneous System Pseudo 15 –
Area Hold-Up Area When any ‘HOLD UP’ type point in this area is in alarm Auxiliary Alert Area When any ‘AUXILIARY ALERT’ type point in this area is in alarm. Vault Area When any ‘VAULT / SAFE’ type point is in alarm. Burglary Area (if event occurs in a specific area): Area Function key #0, #1, ...#9 Area (Pertains to keypad functions keys) On Area When the area is fully armed (ON). Stay 2 (future use) Area When the arming level is STAY 2 (future) Stay 1 Area When the arming level is STAY.
Area Counter reaches Min Considered 'empty'; User Count <= Minimum Point (if event occurs at a specific Point): Counter reaches Max Point Normal (OK) Considered 'full'; User Count >= Maximum Point Open (tripped or tampered--any time) Area No Detected Activity Point Open (disarmed) Area Activity Detected Area 15 Min before Scheduled Arm to "On" Area 15 Min before Scheduled Arm to "Stay" Area 15 Min before Scheduled Disarm Arm to "Off" Area Schedule in Window Area Auto-Command Schedule
Door (if event occurs at a specific door): Floor (pertaining to a specific elevator/lift cab): Door Unlocked Floor Door Locked Out Door Held Open Module (pertaining to an expansion module): Door Forced Module On-Line Door Tamper Module Tamper Door contact circuit cut or shorted. Module Comms Trouble (Subst & Comms) Floor Desecure Door Open Door Secure Module Communication failure or device replaced.
Output to follow an Area "Fail to Arm" (≥V4.80) 4. Schedule is suspended (automatic arming) - In the Areas Control&Status screen it is possible to suspend a schedule. This means that the schedule will be ignored for an area. We should detect if an area does not (auto) arm because the schedule is suspended and set the fail to arm. 5. Arming priorities get in the way. We currently can assign priorities to areas for arming.
E-mail / SMS Messaging The program from version 4.91 allows you to send notifications through e-mail and SMS messages. This functionality is for customers, who want to inform their users about important events such as fire alarms, port communication failures or other manually defined events. The new functionality requires from the customer a working SMTP server (mail server). To enable this option several parameters have to be configured: SMTP server options, such as host name, sender, port, etc.
This window enables to create groups and add users. Groups can be later assigned to specific events. For each user assigned to a group, his own schedule can be specified, and the Send SMS message option enabled/disabled. The SMTP configuration window enables the operator to set options needed for sending email messages. In this window, the operator can set the host name and port, sender address, SSL, and authentication options. SMTP Settings window 21-0381E v4.9.
Schedule window The schedule determines when a notification can be sent to the user and when it cannot. 288 This window is similar to other schedule windows in the program. Verex Director V4.9.1 User's Guide 21-0381E v4.9.
Detect Duplicate Cards Detect Duplicate Cards allows installers to choose if they would like to detect duplicate cards with an account only or across all accounts in the Community Group. A new column has been added to the Community Groups screen to allow the installer to choose the mode of operation. When the Community is configured for detection “Within Each Account Only” then duplicate cards will only be detected at the account level.
To Community “Detect Across All Accounts” Assign Shared Users and Authority ranges: To Community “Detect Within Each AccountsOnly” Assign Shared Users and Authority ranges: 290 Verex Director V4.9.1 User's Guide 21-0381E v4.9.
Create Account “A1 Detect Across All” and Delete “User 1”: Add Community Group “Detect Across All Accounts” to Account “A1 Detect Across All”: Create “A2 Detect Across All” and Delete “User 1”. Add Community Group “Detect Across All Accounts” to Account “A2 Detect Across All”. Create “A1 Detect Within Each” and Delete “User 1”. Add Community Group “Detect Within Each Accounts” to Account “A1 Detect Within Each”. 21-0381E v4.9.
Create “A2 Detect Within Each” and Delete “User 1”. Add Community Group “Detect Within Each Accounts” to Account “A2 Detect Within Each”.
In Account “A1 Detect Within Each” to “User 11” (not a shared User) add Card number “1”: In Account “A2 Detect Within Each” to “User 11” (not a shared User) add Card number “1” – The system WILL ALLOW because it is only looking to detects if that that card number is already in use within this same Account (Doesn’t check that “A1 Detect Within Each” Card number “1” is already assigned to “User 11”): 21-0381E v4.9.
Installation and Technical Reference 294 Verex Director V4.9.1 User's Guide 21-0381E v4.9.
PC Issues and Software Installation Welcome Service Packs: It is always best to stay current on the 'service packs' available for your version of MS Windows, and install them as new ones are released. The topics that follow cover the various aspects of installing and activating a new system. For best results, be sure to scan all of the installation topics that follow, and perform the steps in sections that pertain to your type of installation. MS SQL Server Applications: Beginning with V4.
More: IP Connectivity. UPS Recommendation Standard best practices recommend that all servers and core components of security systems be protected by a suitable Uninterruptible Power Supply (UPS) including surge protection. Other Software The VEREX Director software cannot coexist on a NetVision capture station PC, or on a PC running NetVision v2.1 remote station software. (For the remote station software, simply upgrade to v2.2 or higher.
Hard Drive At least 500 MB of free space while Windows is running is recommended for a full installation and typical database. Software installation may include: The Director software; The card-badging software; MS Internet Explorer components; MS SQL-server components. For demonstration purposes, you can likely install with only 200-250 MB of space available (with Windows running), however this is NOT recommended for a real/working installation.
For the Photo-Badging Option The photo-badging option supports these devices: Video capture device: This feature works with any video or frame-grabber board and supported camera, or any video capture device that is compliant with the "TWAIN" or "Wintab" standard. Writing Tablet: Any writing tablet that works with your version of Windows can be used to capture signatures. Signatures can also be photographed, or entered using your mouse, but a writing tablet is generally recommended.
1024 x 768 (XGA) resolution if supported, otherwise, 800 x 600 (SVGA). High-color or true-color if supported, otherwise "256 colors"; Small fonts (NOT large fonts). Tip: Click [Advanced] to check the font size. Click OK when finished, and respond appropriately to any additional screens that appear.
Software Installation for a Fresh/New System Notes: Panel & Software Revisions: Beginning with v3.20, the VEREX Director software is compatible with panel firmware v2.0 and higher (although some features will require updating the panel firmware and/or modules). Associated panels must be the same rev. level, and the Director software must typically be upgraded to the same level or higher. Notes: Panels V3.3 are required for IP-related features. V1.
database access for each of these workstations. This is required for the VEREX Director software, as well as the Communications software, as applicable. (To start the software, open the Start menu, select VEREX Director V4, followed by Programs, and VEREX Director.) Tip: If you prefer, you can cut-and-paste the ID codes into "Notepad" or "MS Word", and use a floppy-disk to transport the file to the server PC (for registration).
Being told about a certificate problem before any have been assigned can be considered normal operation. If You Are Prompted about a Certificate Problem Continue: To allow logging in--temporarily ignoring any problem with the server certificate. Continue, and don't ask me again: If you will not be using validation certificates for now. Tip: This will be reset when a server certificate is assigned. Stop: To abort the login due to a suspect validation certificate.
Select the database version that you are upgrading from; Click the large [Copy…] button at the bottom of the screen, and follow any additional prompts that appear. When this process is finished, click the X (top-right corner) to close the database update module. To allow the installation to finish, be sure to restart the PC when asked (and follow any additional prompts that appear). information). When finished with this screen, click OK.
If the communications client (modem/panel connection) is being transferred as well: Go into each defined "Communications Pool", and remove all devices (on the left side of the screen), and then delete all devices (on the right side of the screen). 3) 4) QuickRef: VEREX Director-Repair.exe Backup/Restore [ Restore Database ]. Related Topic: Reverting to (Restoring) a Backup Copy of the VEREX Director Database Notice: Do NOT start the Director software yet.
DCOM Setup (Required for Client-Server VEREX Director Systems): Beginning with v4.7, the VEREX Director software no longer uses DCOM, and it does not require any DCOM set up. Firewall Settings (e.g., Windows XPsp2) Beginning with XPsp2, MS Windows includes a 'firewall' that blocks unauthorized access through a network or the internet. Proper operator requires Director software components to be identified to the firewall.
Software Activation and Licensing More: For additional topics related to capacities and supported features, refer to “System Capacities” and “AccountWide Panel Settings”. Software "Activation Key" System capacities and types of expansion / application modules supported depends on your software licensing, which is managed through a small 'activation key'. Activation Key: The VEREX Director software uses a small 'activation key' to manage software licensing and optional features.
If you HAVE Access to the Internet on This PC After entering the Registration Information and Internet Access is available on the Director host PC, select: and press the “Next” button. The License Manager will connect with the Licensing Server over the PC’s Internet connection, to register the key. After a few minutes, a message should appear that the procedure was successful and your validation Key value will be automatically changed. Press the “Done” button at the bottom of this screen.
Upgrading Your Software (Adding Optional Features) To enable the upgraded functionality, you will need to register your system and obtain a new validation key number. The following registration procedures are available with Director Version 4. NOTE: This process must be repeated for each feature added. After the Director program has been installed, run the version 4 License Manager program (Director Server PC if client-server): [Start] Programs VEREX Director VEREX Director – License Manager.
If you HAVE Access to the Internet on This PC March Networks R4-R5 DVR Support If the PC you are working from has Internet Access, select: Press the “Next” button at the bottom of this screen. The License Manager will connect with the Licensing Server to register your upgrade. After a few minutes, a message should appear that the procedure was successful and your 30 character, validation Key number will be automatically changed. Press the “Done” button at the bottom of this screen.
Network USB HASP Key (Director V4.51) Introduction: This optional feature allows running the Director software in an environment such as Microsoft "Virtual Machine" that doesn't support a USB HASP key directly. This feature is supported beginning with V4.51 of the Director software. 310 Instructions: Before installing or upgrading the Director Software: 1) Insert this USB Network HASP key on any regular PC on the network (i.e., not running MS virtual machine).
Remote Software Download and Remote Access (V4.7) Introduction Beginning with v4.7, you can download the Director (client) software across a network, or via the internet for installation on a remote PC. This replaces the previous web browser feature, and supports all features--instead of a limited subset. Requirements Tip: The server(s) and remote clients must be the same revision. If you try to log onto a newer server, you'll be asked if you'd like to automatically download a software update.
Client/Server Issues and the Director Server Manager (v4.7) Problems? See "Troubleshooting", to follow/below. Introduction For systems with client-server licensing, the VEREX Director database can be on one PC, and accessible from multiple client workstations--either on a single network, or through an internet connection. Various licensing options are available to support different numbers of client connections. Tip: The server(s) and remote clients must be the same revision.
to connect out to Director-server on another PC via the internet through a proxy server. Typically not used. Settings: "Proxy Type" (select "None" if not using this feature), "Domain", and a "User Name" and "Password" that has suitable permissions on that domain. (For these and other proxy settings, get an 'IT' person to help you.) - Manager Language: This allows changing the language for this menu and subsequent screens.
Client/Server Access and Permissions Licensing: Client-server operation is optional, and must be selected though the license-manager software. For details on upgrading your licensing, refer to "Software Activation and Licensing" (previous). Assigning a Certificate to the Director Server How to Get Here (Locator) Select Server Access from the MyTools bar, or from the 'tree', select [Management], PC Access (+), and Server Access. Server Validation Certificates (V4.72) Introduction Beginning with v4.
well as the Communications software, as applicable.) Client Access (Allowable Client List) Tip: This is not needed (does not apply) for communications client software on the same PC as the Director-server. Allowable Client List In a client/server system, client workstations are given access to the central database by identifying them to the server. (After installing the VEREX Director software at the server and client workstations.
Now, click [+] at the bottom of the form, or right-click the form, and select Add New from the pop-up menu. Alternative: You can also select a blank/grey item from the list (Forms view: bottom of the window). Now, refer to the selection-descriptions for this screen while entering and/or selecting your desired settings.
Screen Reference [Management] PC Access Client Access - Client Description (bottom of form): This is where you select a client workstation (or communications client) to view or edit. This area shows the name of each defined client workstation; - Cyclic ID: This is a 16-digit number obtained from each VEREX Director client PC (under "About..." from the Help menu on each specific PC).
Setting Up Client Permissions Introduction If you Need to Delete a Permission-Set 'Client permissions' allow blocking (or granting) access to individual features for all operators at each client workstation. Before attempting to delete a permission-set, you must first check to ensure that it is not assigned to any client PCs (and assign a different one as necessary.) Tip: For each specific item, click once to allow viewing only (magnifying glass), or click again to allow viewing and editing (pencil).
[Management] PC Access Client Permissions Screen Reference Pick-List (bottom of the form) - Client Permission: This is where you select a permission-set to view or edit. This area shows the name of each defined permission-set to use with client software; On This Form - Name: A suitable name/description for this permission-set (such as "Admin PCs"). Common Permissions - These are permissions pertaining to the entire system (such as editing operators, backing up the database, etc.
New Installation? Try the Wizard ! Users Shared Across Multiple Accounts: Beginning with Director V4.20, groups of users (and holidays) can be set up once, and then applied to multiple accounts. If your system will include these features, be sure to skip these topics (plus authorities) in the wizard. Beginning with V4.0 of the VEREX Director software, you can let a helpful "Wizard" lead you through some common tasks. Check the new Tools menu to see the Wizards that are available. In V4.
Panel Connection Overview Beginning with V4.0 VEREX Director, you can use the Communications Wizard to set up and initiate communications with a panel. For more information, refer to "New Installation? Try the Wizard!" Connections Supported (V4.4) Line Type HSC IP or secure IP Bell 103 External 56k modem W.W. modem (w/o STU) xL panels Yes 5 W.W.
any wiring instructions for your hardware. For a dial-up modem connection, refer to "PC and Panels—Modem Connections" in addition to any wiring instructions for your hardware. Note: Modems require additional set-up as described in the indicated section. 2) Make Your Software Aware of Modems and Direct-Cable-Connections Ensure the communications service is aware of your modems and serial (or IP) connections to be used for panel communications.
IP Connectivity Secure IP Communications (V4.72) Introduction VEREX Director systems support communications through a secure IP connection. This can be: Utilized through a network, or via the internet. Used for central monitoring (HSC-IP), panelPC communications, and/or client/server communications. Operation Item Director software IP Module firmware Panel Firmware Receiver Requirements: Client/Server via Secure IP V4.70 (w/o cert's) v4.
Certificate Files: Obtain through your dealer. Assign for the Director Server: [Management], PC Access (+), Server Access. Details: Server Validation Certificates Assign for each Communication Client: [Management], PC Access (+), Client Access. Details: Client Access (Allowable Client List) Assign for a Receiver (Monitoring via HSC-IP): Refer to the programming guide for the receiver. e.g., R1000 Receiver: 21-3690x Director Software: Client/Server via Secure IP: No set-up needed.
Settings, Control Panel, and Phone and Modem Options. 3) Select the "Modems" tab, and click [Add]. 4) 5) Select "Do not detect...", and click [Next]. Under "Standard Modem Types", select "Communications Cable between two computers", and click [Next]. Select the serial port (COMx) that the cable will be using, and click [Next]. 6) 7) Click [Finish]. 8) In the next screen, click [OK] to close the screen.
PC and Panels—Modem Connections Tip: For details on the types of modems supported, refer to "PC Issues and Software Installation". Panel & Software Revisions: VEREX Director software V3.2 can connect with panels V2.0. Associated panels must be the same rev. level, and the Director software must typically be upgraded to the same level or higher. Exception: V3.3 panels OK with V3.20 software for this type of connection (i.e., non-IP).
central monitoring facility through the built in (or modular) modem and/or an IP connection ( V3.3 panels), or high-security communications--HSC (via Mark7/DVACS service in Canada). 21-0381E v4.9.
Serial Port / Modem Setup (Communications Manager) Beginning with V4.0 VEREX Director, you can use the Communications Wizard to set up and initiate communications with a panel. For more information, refer to "New Installation? Try the Wizard!" To manually set up a panel connection, refer to "Panel Connection Overview". The initial topics in this section provide general information and details on starting the communications software module.
Identifying the Server to a PC Running only the Communications Software Open the Windows task-bar (move your mouse to the bottom-right of the screen), rightclick the LCD/Telephone symbol, and select Server Location. If this symbol is not present: Start up the communications software as described previously / above. If the right-click menu does not appear: This may mean that the Director-server PC or software is not running, or the activation key is not installed on the server (or only) PC.
When You Select "Port Configuration" (Right-Click the LCD/Telephone Symbol on the right-hand edge of the TaskBar) Screen Reference - Start Communications: Select this to restart the Director-Communications service (e.g., after stopping it previously). - Stop Communications: Select this to stop the Director-Communications service. Attention: Stopping the communications service is NOT recommended while any panel updates are in progress.
are also supported. More: IP Connectivity" Tip: The right-click menu provides "Add" and "Delete" selections for utilizing additional connections on this PC, or deleting ones that are no longer needed. Note: Parallel connections (LPT ports) do not apply to this application.
Communication Pools for System Panels Beginning with V4.0 VEREX Director, you can use the Communications Wizard to set up and initiate communications with a panel. For more information, refer to "New Installation? Try the Wizard!" About Communication Pools "Communication pools" allow the VEREX Director software to manage panel communications. Each 'pool' can contain a direct-cable-connection, or one or more modems or IP connections. IP Connections: Secure and regular IP connections are also supported.
Deleting a "Communication Pool" [Communications] Communication Pool Before deleting a 'pool', check to ensure it is not presently being used by a panel communications session: Select Communications from the MyTools bar, or click [Communications] in the 'tree', and select Pending/Online. Now, for each active communications session (selected at the bottom of the screen), click the panel group near the centre of your screen, and view the 'Comms Pool' and 'Results' information on the right.
Setting Up a New System (Commissioning) Note (v4.
Before You Begin (Form-by-Form Data Entry) Do I Need an LCD Keypad?: Setting up a new system/panel does not require an LCD keypad to be installed. (You only need to know the serial number of each main panel and expansion module--look for a small hand-written label on the back of each circuit board.) Transferring settings from an Existing Panel: In this case, you will need an LCD keypad to view (or set) the "Panel Code" (S001:5) and "Third-Party Password" (S005:1).
Basic Settings for Testing, and Panel Communications Nothing feels better when setting up a new system than that first "Access Granted". If your system does not include door control, the equivalent might be verifying that first motion sensor as being monitored only when the area is armed (On), or checking system status through a system (LCD) keypad.
10) From the installed devices, select one LCD keypad module, one door controller module (if applicable), and one point expansion module, and define these items through the software. "Modules (PODs)" 11) Similarly, select 1 - 3 doors, and monitored sensors, and create entries for these items. "Doors, Readers, and Related Settings", and "Input Points— Monitored Sensors". 12) Select which system (equipment) conditions are to be monitored or ignored. "Equipment Settings (Pseudo / Internal Inputs)".
Importing Settings from an Existing VEREX Director System Panel Panel & Software Revisions: Beginning with V3.20, the VEREX Director software can connect with panels V2.0 and higher. Associated panels must be the same rev. level, and the Director software must typically be the same level or higher. Exception: V3.3 panels OK with V3.20 software (if IP-related features are not needed).
Customizing the MyTools Bar You can Customize Your MyTools Bar The MyTools bar/list can be customized as desired. The MyTools settings are saved separately for each operator, allowing everyone to use their preferred layout. Tip: The contents of your MyTools bar (i.e., for the present operator) are saved automatically when you change any settings through this screen. Changing the Look or Content of Your MyTools Bar Tip: If you are doing this for someone else, be sure to login as that operator.
Screen Reference View (menu) MyTools Customize - Show Button Captions in MyTools: Whether or not you want the textdescriptions to appear for items in your MyTools bar. - Show Button Icons in MyTools: Whether or not you want the graphic symbols to appear for items in your MyTools bar. - Icon Position: This selects the position of the graphic symbols relative to the text-description for each item in the MyTools bar (above, below, to the left, or to the right).
System Capacities Software Licensing and Activation Key Checking or Updating Your System Capacities Maximum system capacities and types of expansion / application modules supported depends on your software licensing, which is managed through a small 'activation key' and the license-manager software. To update your system capacities, refer to "Software Activation and Licensing". To check your present system capacities, open the Help menu, and select [About].
-- +1 / +5 DVRs March Networks DVRs -- +1 / +5 R5 DVRs -- R4 DVRs (unlimited) 1 - 1023 ‡ 1 - 1023 ‡ (V4.7) 1 - 1023 ‡ ‡ (V4.7) 1 - 1023 ‡ ‡ Notes and Exceptions: ‡ Optional via licensing; § For new systems / updated hasp key only; * To support doors/access-control and/or 'memory model' 4, xL panels (narrow mainboard) require a feature expansion board; Client/Server operation also allows multi-server login; Adding panels allows for more areas, sensors, doors, etc.
systems, while local system configuration is supported only in single panel systems set to "Feature Set" 1, 2, 3, or 4. Exception: Keypad programming is supported in all systems for any 'application' modules that require this due to custom settings stored only at the module itself (HSC/printer module, RF/wireless module, and Smart PODs). For details on setting the 'memory model', refer to "Account-Wide Panel Settings...". Schedules: (Depends on panel type and memory-model supported.) 50: V4.
Common Per-Panel Capacities (not based on 'Feature-Set') Expansion / Application Modules: 24 system LCD keypads and/or other modules, or 60 suite-security keypads (see exceptions). Floors: The "Enterprise" version of the software supports 124 unique accesscontrolled floors.
Class ‘A’ (4 wire loop) Class ‘B’ (2 wire loop) Tamper LCD keypad Suite Keypad Fire module MAP annun. RF module Door ctrlr I/O expansion Elevator Controller - - - - - - - - - - - - - - New style modules (V4.4): These use custom circuit types (configurable). Readers / Doors LCD keypad N/A Suite Keypad - Fire module N/A MAP annun.
Advanced Database Features already using SQL server to manage other databases.
User-Logins (Needed for: Database Query, and SQL Server Support) User 'Logins' The Table Repair Utility The "Database Query" feature, and SQLserver support require you to provide some login information that will be used to access the VEREX Director database. In a client-server VEREX Director system, the database/table repair utility is available only through the server PC. (This is the PC that includes "...Director-Server.exe".
VEREX Director-Repair.exe User Logins Setting Up "User Logins" Before starting the table repair utility, ensure that all copies of the VEREX Director software (and associated server and communications components) are shut down. ------------------------- At your VEREX Director workstation (server PC if client-server) open the Windows Start menu, and select Programs, VEREX Director V4, and VEREX Director-Repair.
Linking to the Database (Used for: Custom Query/Reporting; ERM Integration) Introduction Director's "Database Query" feature allows you (or your custom software) to link to the database, and view or use the data as desired. (This pertains to read-only database 'views' (provided) that mirror the contents of the database.) This allows setting up custom reports (e.g., setting up your own custom queries in MS Access, or using a program such as "Crystal Reports".
4) You can ignore most of this screen. At the very bottom, open the "Files of type" field [], and select "ODBC Databases ()". 5) 6) This screen will appear: Select: User Data Source (...) at the top, and click [ Next ]. 7) In the next screen: You can ignore most of this one, too: Select: SQL Server in the list, and click [ Next ]. 8) In the next screen, click [ Finish ]. Just select Machine Data Source at the top, and click [ New ]. 350 Verex Director V4.9.1 User's Guide 21-0381E v4.9.
If you see any additional screens before the one shown below, respond appropriately ( [Next], etc.). 11) In the next screen, make selections similar to as shown: Tip: If asked to log in, enter the "DirectorQueryUser" login name and password. Exception: Auto card-import tasks involving the 'ErmUserImport' and 'ErmUserImportResult' tables require the "ImportUserLogin" login name and password. 9) In the next screen, enter a suitable data source "Name", plus a "Description" if desired.
13) In the next screen, click [OK], or [Test Data Source], as desired: 15) Now, select the VEREX Director database view(s) that you want to be available to you: When ready, click [ OK ]. 16) Your selected VEREX Director database view(s) are now linked to your new database. Tip: A successful "Test" indicates you've entered correct login data, etc.
Automated User-Import (Used for: ERM Integration) [Management] Database Maintenance User Import Introduction VEREX Director provides an automated user import feature-allowing it to be interfaced with a personnel management system (Also called: "Enterprise Resource Management"). Caution: This requires source data with very specific structure.
- Enable Periodic Processing of User Import Table: Select this to 'turn on' the automated card import feature. - Period (in minutes): This is how long Director will wait before processing the 'ErmUserImport' table again (e.g.
Manually Importing User-Data From a Text File Introduction User data an be imported from an external file if necessary. Caution: This requires a source text file with very specific structure (otherwise, the database can become corrupted). As such, this feature should not be used by persons who are unfamiliar with computers or text file formats. Authority: users. Importing Card Data Manually 1) As a precaution before using this feature, ensure you have an up-to-date backup copy of the database.
System / Hardware Reference System Design Aspects (Topology) The following concepts can be 'mixed and matched' as desired when designing a system: PCs / Environments: The VEREX Director software can be installed for use on a singlePC, or across multiple PCs in a network environment. Different aspects of the software will be installed, depending on what each PC is used for (database server, operator workstation, and/or for panel/modem connections).
connections are 'serial', with or without conversion to "RS485". (RS485 connections allow for longer distances, and/or multiple panels per connection.) IP Connections: Secure and regular IP connections are also supported. More: IP Connectivity Dial up panels with dedicated external modems (one panel per modem) can be set to automatically dial-in to the VEREX Director system to transmit alarms or blocks of activity messages.
however, if window contacts and/or motion detectors are used. Smoke Detector: This is a smoke detector that senses smoke or flame, triggering a local alarm as well as transmitting an associated message to the monitoring station. The Monitoring Station, in turn, is able to notify the fire department on a 24-hr a day basis. Panic Alarm: A panic alarm is another type of detector that can be added to a centrally monitored system.
Keypad Tone Reference (V4.5 with V4.42 firmware) The following table shows keypad tones for the indicated conditions. Tones that are different for “Standard” vs. “Reversed” are shown in bold. Tip: “Standard” versus “reversed” tones is selectable under: Account Information, Setup, ”Arm/Disarm and Tones”. LCD keypad Tones Condition Fire Chime Exit/Entry Delay Exit Delay with point open (see note below) Standard Tones 1 second on and off.
Table 2: Arming station Tones Condition Fire Chime Exit/Entry Delay Exit Delay with point open (see note below) Confirm Exit delay Trouble – Alarm, Standard Tones 3 times 500 ms on and off, then there 1 second gap Double short : 125 ms on and 125 off four times Slow cadence: slow on/off tones On Time: 250 ms Off Time:750 ms Fast cadence: fast on/off tones On Time: 250 ms Off Time: 250 ms Fast cadence: fast on/off tones: On Time: 250 ms Off Time: 250 ms Steady continuous tone Area Fail to Arm (see note b
On-Line Support & Product Information www.utcfssecurityproducts.eu/suppor t On-Line Information and Support The Interlogix web site (http://www.interlogix.com) provides access to product marketing and support information 24 hours a day, 7 days a week. Interlogix provides all product data-sheets and marketing materials as Adobe® PDF files for direct download and printing. Installation instructions and user's guides for current products are also available in PDF format.
Additional information 4) Follow the screens that appear. If selecting your modem manually, select the brand, and then the specific model in the list. When finished, click [Next]. 5) Select the serial port (COMx) to be used for the connection, and click [Next]. 6) If a screen appears with a spot for your 'Area Code', and other items, respond appropriately, and [Close] this screen when finished). Click [Next], [Finish] and/or [OK] as required to complete the process.
Index Absentee report ................................................ 13 Access ...... 26, 146, 154, 163, 245, 261, 266, 276 Card format ................................................. 240 During comms failure .......................... 175, 240 Reporting on User Access Rights (by Area¸ Door¸ or Floor) .......................................... 26 User-photo verification .................................. 48 Access control 146, 154, 163, 175, 245, 261, 266, 276 Card format ...............................
Text paging (Serial Reporting) .................... 226 Alarms (blocking unwanted alarms from 'pseudos') .................................................... 243 Allow duress ................................................... 213 Antipassback status ........................................ 107 Resetting for one user or everyone ............... 87 Resetting for users in a specific area .......... 107 Apartment ....................................................... 261 Suite-Security Keypads................
Changing settings for ...... 141, 146, 154, 256, 296 An account folder (renaming) ...................... 197 Areas .......................................................... 245 Authorities for users/entrants ...................... 154 Cardholders/entrants .................................. 163 Custom input point types............................. 291 Daylight-savings date .................................. 149 Doors ..........................................................
3A - Setting up Shared Users ..................... 209 3B - Defining groups of shared holidays ..... 210 4A - Assign Groups of Shared Users to Accounts (Shared User Management) .... 211 4B - Assign Groups of Shared Holidays to Accounts (Shared Holiday Management) 212 Computer requirements .................................. 317 Condo ............................................................. 261 Suite-Security keypads ............................... 261 Condominium LED keypads ............................
Database backup ............................................ 184 Database query............................................... 376 Activate for a typical system........................ 374 Date format settings ........................................ 320 Daylight-Savings and Standard time Dates for time-change ................................. 149 Synchronize panels after time-change .......... 85 DCOMCNFG ................................................... 329 Dealing with alarms (Comment/Resolve) ........
Automated user/card import ........................ 380 Error messages due to database damage ...... 182 Errors Checking for panel vs. software differences/conflicts ................................ 179 During a panel-update session;Don't decide now ......................................................... 129 Partial updates shown in Yellow/Green in user list ........................................................... 164 Escort Privilege ............................................... 158 Event...........
Information on products .................................. 388 Initial Set Up of Views, Maps, Cameras ................................. 70 Input points ..................... 284, 288, 290, 291, 294 Check status of input points ........................ 117 Custom circuit types .................................... 294 Duplicated numbers (see display offsets) ... 230 Video Events ............................................... 288 Input points (Monitored Sensors) ....................
Duplicated numbers (see display offsets) ... 230 Modules and related setting ............................ 256 Monitoring ............................................... 144, 236 A guard tour in progress ............................... 52 Listing only specific events/alarms ................ 43 Monitoring Paging & Remote Mgt. Settings 236 Remote cameras........................................... 58 Scheduled event filtering for operators ....... 144 The system monitoring window .....................
Check status ................................................. 92 Define/setup ................................................ 230 Find/select..................................................... 10 Selection not available (greyed-out) .............. 10 Set panels/groups to appear in the tree or on forms ......................................................... 10 System Panels and Displayed Item-Numbers ................................................................ 230 System settings for each panel ...
Repairing database tables .............................. 182 Replacing a main panel .................................. 230 Report ............................................................... 32 Also see Reports .......................................... 13 Creating custom queries and reports .......... 376 Import archived data to report on ................ 191 Reporting .......................................................... 32 Also see Reports ..........................................
Setting the Maximum Camera-Image Size........ 68 Setting the Panel Service PIN for this Account217 Setting up (configuring) guard-tours .................. 54 Setting up a new system ................................. 345 Try the Configuration Wizard ...................... 345 Setting up Multi-Panel Arm/Disarm ................. 254 Setting up Panel Groups ................................. 228 Setting up required-attendance time periods .... 17 Setting up Shared Holidays (and/or Time-Change Dates) ............
Checking status by area ............................. 101 Checking status of a Suite Security System . 99 Checking status of doors ............................ 110 Checking status of expansion modules......... 96 Checking status of input points ................... 117 Checking status of system/equipment conditions .................................................. 92 Login automatically to control & status........ 136 Outputs ....................................................... 119 User In/Out Status ...
Add or view/change settings ....................... 163 Area Users (Activity¸ User Count¸ and APBReset) ..................................................... 104 Assign Groups of Shared Users to Accounts (Shared User Management).................... 211 Custom Information Categories for Users ... 161 ID# Reservations for shared users .............. 207 Printing or viewing sorted lists of users ......... 29 Reset APB by area ..................................... 107 Resetting APB status ......................
