Instructions / Assembly

ManualsBrandsVeranda ManualsLumber & CompositesWhite Vinyl Dover Fence Gate Kit

68956 U.S. Hwy 131, White Pigeon, MI 49099 1-855-556-1852 8724_3/16

www.ufpi.com

Dig post hole for the hinge post 18" to 24" in diameter and 36" to

42" deep (depending on local ordinance or expected frost depth

in winter). We recommend that you insert a piece of 4x4 treated

lumber to support the gate hinge post. See ﬁg. 1.

Actual gate size will vary. The inside post-to-post dimension

will be the width of the gate plus 1-1/4". Double-check all

measurements!

Check local ordinances and regulations before building your

fence. Before construction, contact your local utility companies

to mark any underground cables and pipelines. In addition, it is

a good idea to discuss plans with any neighbors along your

proposed fence line.

Step 3Preparation

Digging post holes

Items you may need

• Dover or Overland

fence panel

• Drill driver

• 1/4" drill bit

• Circular saw with a ﬁne-

tooth blade or hand saw

• 7/16" wrench

• Tape measure

• Pencil/marker

• Safety glasses

• 4x4 treated wood post

Kit contents

• 2 — Gate jambs

• 2 — Gate hinges

• 1 — Gate latch

• 2 — Corner braces

• 2 — Jamb covers

• Fasteners

VINYL FENCE GATE KIT

ASSEMBLY INSTRUCTIONS FOR

DOVER AND OVERLAND PANELS

ﬁg. 1

Dover Gate

Overland Gate

Vertical Horizontal

Summary of content (6 pages)

PAGE 1
VINYL FENCE GATE KIT ASSEMBLY INSTRUCTIONS FOR DOVER AND OVERLAND PANELS Items you may need Kit contents • Dover or Overland fence panel • 7/16" wrench • 2 — Gate jambs • 2 — Corner braces • Tape measure • 2 — Gate hinges • 2 — Jamb covers • Drill driver • Pencil/marker • 1 — Gate latch • Fasteners • 1/4" drill bit • Safety glasses • Circular saw with a finetooth blade or hand saw • 4x4 treated wood post Preparation Step 3 Check local ordinances and regulations before building your fence.
PAGE 2
VINYL FENCE GATE KIT ASSEMBLY INSTRUCTIONS FOR DOVER AND OVERLAND PANELS CONTINUED Measuring and trimming gate components using Dover panel Measuring and trimming gate components using Overland panel Note: For assembly using the Overland Panel, see next section. For optimal performance and aesthetics, we recommend a walk gate width of 40-1/2". This is accomplished utilizing the width of 4 pickets from the Dover fence panel. STEP 1 Measure the opening where your gate will be installed.
PAGE 3
VINYL FENCE GATE KIT ASSEMBLY INSTRUCTIONS FOR DOVER AND OVERLAND PANELS CONTINUED Assembling the gate STEP 1 Lay all gate components out on a flat, clean surface. Reassemble the panel by inserting the pickets into the top and bottom rails. Ensure that all rails are flush with the pickets. STEP 2 Slide the gate jamb onto the fence panel and place the hinges at the center of the fence rail. Using the hinge as a guide, drill the four (4) necessary ¼" holes for the hinge bolts.
PAGE 4
INSTRUCCIONES DE ENSAMBLAJE DEL KIT DE PUERTA DE CERCA DE VINILO PARA PANELES DOVER Y OVERLAND Artículos que puede necesitar: Contenido del kit • Panel de cerca Dover o Overland • Llave inglesa de 7/16" • 2 — Jambas para puerta • Cinta métrica • 2 — Bisagras para puerta • 2 — Cubiertas para jambas • Taladro • Lápiz/marcador • 1 — Pestillo para puerta • 2 —Soportes esquineros • Sujetadores • Broca de 1/4" • Lentes de seguridad • Sierra circular con cuchilla de • Poste de madera tratada dientes fi
PAGE 5
INSTRUCCIONES DE ENSAMBLAJE DEL KIT DE PUERTA DE CERCA DE VINILO PARA PANELES DOVER Y OVERLAND, CONTINUACIÓN Medición y recorte de los componentes de la puerta utilizando el panel Dover Medición y recorte de los componentes de la puerta utilizando el panel Overland Nota: Para el ensamblaje utilizando el panel Overland, consulte la siguiente sección. Para un desempeño y una estética óptimos, le recomendamos un ancho de puerta de acceso de 40-1/2".
PAGE 6
INSTRUCCIONES DE ENSAMBLAJE DEL KIT DE PUERTA DE CERCA DE VINILO PARA PANELES DOVER Y OVERLAND, CONTINUACIÓN Ensamblaje de la puerta PASO 1 Coloque todos los componentes de la puerta sobre una superficie plana y limpia. Vuelva a ensamblar el panel insertando las estacas en el barandal superior e inferior. Asegúrese de que todos los barandales estén alineados con las estacas. PASO 2 Deslice las jambas de la puerta en el panel de la cerca y coloque las bisagras en el centro del barandal de la cerca.