Installation Instruction

ManualsBrandsVent-a-Hood Manualscooker hoodsM58PSLDSS

Page 1

L154 0810B

CUS

Read and Save These Instructions

All Hoods Must Be Installed By A Qualied Installer

INSTALLATION INSTRUCTIONS

WALL MOUNT LINER INSERT WITH

M600 OR M1200 BLOWER

Read All Instructions Thoroughly Before Beginning Installation

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualied

person(s) in accordance with all applicable codes and standards,

including re-rated construction. Switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally during installation.

B. When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

C. Ducted fans must always be vented to the outdoors.

D. Sufcient air is needed for proper combustion and exhausting

of gases through the ue (chimney) of fuel burning equipment to

prevent back drafting. Follow the heating equipment manufacturer’s

guideline and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and local code authorities.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL

DUCTWORK

Summary of content (6 pages)

PAGE 1
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT WITH M600 OR M1200 BLOWER Read All Instructions Thoroughly Before Beginning Installation WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
PAGE 2
Ducting Do’s and Don’ts NEVER restrict the duct size. The single blower unit (M600) requires 6” round duct or equivalent (28 square inches), and the dual blower unit (M1200) requires 10” round duct or equivalent (79 square inches). Using Vent-A-Hood ducting products (back page) will ensure proper efficiency. Blower Single (M600) Dual (M1200) Duct Size 6” round or equivalent 10” round or equivalent Sq. Inch Area 28” 79” Vent-A-Hood Transition N/A VP566 (Inlcuded) Do not use flexible or corrugated duct.
PAGE 3
Installation Details 1) Read all instructions thoroughly before beginning installation. Note: These instructions apply to standard liners only. Custom liners may require additional specification consideration. 2) When installing a MSLD wall mount liner (19 1/4” deep), it is recommended that the bottom edge of the liner be located no more than 24” - 27” from the cooking surface.
PAGE 4
Installation Details Continued 4) Remove the liner from its packaging and place it back side down on the floor or countertop in front of the wall where it will hang. 5) Remove the nuts retaining the safety straps on the inside ends of the liner shell. Pull the safety straps off of the studs to disengage. Separate the lower filter/control section from the liner shell by pulling them apart. These sections only are held together by snaps once the safety straps are disengaged.
PAGE 5
Installation Details Continued 12) To confirm a flush alignment into the decorative enclosure, temporarily snap the filter/control section into the liner shell. Adjust corner screws if necessary. 13) Unsnap the filter/control section from the bottom of the liner shell and insert wood screws (included) in the remaining holes along the bottom edge of the liner shell.
PAGE 6
VENTING ACCESSORIES WALL LOUVER WALL LOUVER 8 �⁄�” WALL LOUVER 13” 11” Back View 6” 7” 8” RECTANGULAR WALL LOUVER Back View 11” 8 ½” 13” 1 ½” Flange 1 ½” Flange 10” Back View 3 ¼” 6” 1 ½” Flange 1 MODEL DIM VP526 VP527 VP528 6” Round 7” Round 8” Round LOW PROFILE ROOF JACK (MAXIMUM 4/12 PITCH) 16 ¾” 6 ½” MODEL DIM VP554 10” Round 6” Round 7” Round 8” Round ADJUSTABLE ELBOW MODEL MODEL 10” Round 12” Round 10” 12” 8 ½” DIM VP562 VP563 6” & 8” to 10” 8” & 8” to 12” OFFSET