RANGE HOODS INSTALLATION INSTRUCTIONS - USE AND CARE ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: CLEANING AND OPERATION INFORMATION ON PAGES 8 to 11. REGISTER YOUR PRODUCT ON LINE AT: www.venmar.ca 07020 rev.
! WARNING ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 1. 2.
ABOUT THIS MANUAL Because of the large amount of models covered by this publication, the illustrations are typical ones. Some details of your unit may be slightly different of the ones shown. Please take note this manual uses the following symbols to emphasize particular information: ! WARNING Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death.
1. INSTALL DUCTWORK Plan where and how the ductwork will be installed. Install proper-sized ductwork, elbow(s) and roof or wall cap for the type of blower you are installing. If using 6’’ (150 mm) round ducts, use a transition. Use 2’’ (50 mm) metal foil duct tape to seal duct joints. Roof cap Roof cap 6” round duct 3¼” x 10” duct 3¼” x 10” to 6” round transition Wall cap Wall cap Hood Hood HH0014A HH0011A 2. MEASURE THE INSTALLATION Dimensions for the most common installations are shown below.
3. PREPARE THE INSTALLATION (CONT’D) NOTE: If the bottom of the cupboard is recessed, attach wood strips (not included), as shown below, in order to properly install the range hood (A) or charcoal filter unit (if need be) to the cabinet (B). The wood strips must be as thick as recess. B A 23 8 ” HD0033 HO0002A Cut-out the openings for duct (A) and power cable (B), in cabinet or wall, according to the direction of discharge chosen. See figures below.
4. PREPARE THE HOOD (CONT’D) Using a long nose pliers, remove the knock-outs for the chosen opening (vertical on top or horizontal at the back of the hood). See figures below. VERTICAL DISCHARGE: 1 2 3 HORIZONTAL DISCHARGE: 1 2 3 HR0018 5. INSTALL THE ADAPTER/DAMPER NOTE: If this hood replaces another one, please note that the location of the air exhaust can vary from one manufacturer to another. HORIZONTAL DISCHARGE, NEW INSTALLATION Fold down the foldable flange (C) of the adapter/damper.
6. INSTALL THE HOOD Run power cable to installation location. Place the hood at its location. Using a pen, mark the position of the screws (smaller part of the embossed keyholes). Remove the hood and install (4) 1/2” double thread screws at sides locations (A), leaving a 1/8” gap. Place the wire clamp, insert the cable in the hood and tighten the wire clamp to secure the cable. Place the hood under the cabinet and slide it in position.
9. HALOGEN LIGHT BULBS This range hood uses 120 V, 50 W, MR16 or PAR16 with GU10 base, shielded halogen lamps (included in Connaisseur models only). ! WARNING In order to prevent the risk of personal injury, do not install a lamp identified for use only in enclosed fixtures. Install the lamps by placing the bulb leads into their grooves in the socket and gently push upward and turn clockwise until secured.
10. CLEANING (CONT’D) STAINLESS STEEL CLEANING (CONT’D): Avoid: when choosing a detergent - Any cleaners that contain bleach will attack stainless steel. - Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly. - Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be used close to a range. ENAMEL FINISH: Clean with warm water and mild detergent only.
11. OPERATION (CONT’D) MECHANICAL PUSH-BUTTON CONTROL HC0021 A B C A. OFF BLOWER SWITCH: Press on this switch to stop the blower operation. B. SPEED BLOWER SWITCHES: Press on left switch (1) to turn on the blower on low speed, on middle switch (2) to turn on the blower on medium speed, and on right switch (3) to turn on the blower on high speed. C. ON/OFF LIGHTING SWITCH: Press on this switch to turn on the lights, and press again to turn them off. OVAL ELECTRONIC CONTROL HC0022 A B C D A.
. OPERATION (CONT’D) ROUND ELECTRONIC CONTROL HC0023 A B C D A. DELAY SWITCH: When a blower speed is selected, press this switch to activate the delay function. The corresponding blower speed switch will flash to indicate this function is activated. The blower will continue to operate for 5 minutes and will stop automatically. To cancel the delay function, press the delay switch once again. B.
. SERVICE PARTS C180, HDN17, V10 & V30 SERIES SINGLE BLOWER RANGE HOODS 1 2 KEY NO. PART NO. 1 2 4 5 6 7 * 13296 16153 16150 16151 16152 01988 01757 14131 05921 07020 * 04281 3 7 3 7 QTY.
