KLI 110 Instructions for control keypad VAS 452423-2009-12
Contents of packaging Important information / warnings 3 4-5 Operation 6 Set-up and programming 7 Security key Configuring control keypad KLI 110 - in addition to existing remote control KLR 100 2 + 7 8-13 + 8-9 - to control electrical products connected to control unit KLC 500 10-11 - in addition to existing control keypad KLI 110 12-13 Removing/adding control of electrical products connected to control unit KLC 500 b 14-15 Changing security key 16 Resetting 17 Installation 1 3 18-
Important information Warning – To reduce the risk of severe injury or death: Read instructions carefully before installing and operating. Please keep instructions for future reference and hand them over to any new user. Safety • Never let children play with the control keypad. The keypad should be fitted out of reach of children at a minimum height of 5 feet (1.5 m). • The product must not be put into operation until it has been fitted according to these instructions.
+ - d c a b + + KEY + LED PRG - Set-up and programming Note: Do not fix control keypad KLI 110 to the wall until set-up and programming have been completed and it has been verified that the relevant products can be operated from the proposed position. Operation Keys for operating the product a OPEN/UP or CLOSE/DOWN Short key pressure: Product will travel to maximum top or bottom position. Long key pressure: Product will travel only until the key is released.
Configuring control keypad KLI 110 in addition to existing remote control KLR 100 (supplied with electrical skylight) 1 Copy and transmit system from remote control KLR 100 as de- scribed in the user manual for KLR 100. 2 Press PRG button on control keypad KLI 110 for max 2 seconds to receive system in the keypad. Reception can take up to 2 minutes. LED flashes green slowly.
Configuring control keypad KLI 110 to control electrical products connected to control unit KLC 500 4 2 1 Disconnect all products that are not to be controlled by control 3 max 5 sec keypad KLI 110 from control unit KLC 500. Note: In case of new electrical products, complete item 2 within 10 minutes from reconnection. 2 Transmit system from keypad by pressing the PRG button for max 2 seconds. Transmission can take up to 2 minutes. LED flashes green slowly. 3 Remove cover from control unit.
Configuring control keypad KLI 110 in addition to existing control keypad KLI 110 5 1 Disconnect all products that are not to be controlled by control keypad KLI 110 from control unit KLC 500. 2 Transmit system from existing keypad by pressing the PRG button for 3-4 seconds. LED flashes green slowly. 3 Press PRG button on additional control keypad KLI 110 for 2 1 4 Remove cover from control unit.
Removing/adding electrical products connected to control unit KLC 500 from/to control keypad KLI 110 4 1 Disconnect all electrical products and reconnect only products to be 1 2 3 PRG max 5 sec removed from/added to control keypad KLI 110. Complete item 2 within 10 minutes from reconnection. 2 Remove/add control and transmit functions by pressing PRG button in keypad for max 2 seconds. This procedure can take up to 2 minutes. LED flashes green slowly. 3 Remove cover from control unit.
1 2 KEY min 5 sec PRG KEY min 5 sec 3-4 sec Changing security key Resetting The security key of the system must be changed if security may have been compromised, eg if a remote control is missing. The security key is changed in one control keypad only and then transferred to the remaining keypads/remote controls in the system. The control keypad KLI 110 can be reset to its initial factory settings. Press PRG button for at least 5 seconds. LED flashes red quickly.
Installation Fix keypad to wall with screws or double-sided adhesive tape.
www.velux.com installation instructions for Kli 110. ©2009 VELUX Group ®VELUX and the VELUX logo are registered trademarks used under licence by the VELUX Group USA: VELUX America Inc. 1-800-88-VELUX CDN: VELUX Canada Inc. 1 800 88-VELUX (888-3589) AUS: VELUX Australia Pty. Ltd 1300 859 856 NZ: VELUX New Zealand Ltd. 09-6344 126 J: VELUX-Japan Ltd.
