Operating instructions

Table of contents
Drive converter cabinet units
8 Operating Instructions, 10/2008, A5E00288214A
4.8 Signal connections ...................................................................................................................... 62
4.8.1 Customer terminal block (-A60) .................................................................................................. 62
4.9 Other connections....................................................................................................................... 70
4.9.1 dv/dt filter plus Voltage Peak Limiter (option L10) ...................................................................... 70
4.9.2 Sine-wave filter (option L15) ....................................................................................................... 72
4.9.3 Connection for external auxiliary equipment (Option L19).......................................................... 74
4.9.4 Main switch incl. fuses or main circuit breaker (option L26) ....................................................... 75
4.9.5 EMERGENCY OFF pushbutton installed in the cabinet door (option L45) ................................ 77
4.9.6 Cabinet illumination with service socket (option L50) ................................................................. 78
4.9.7 Cabinet anti-condensation heating (option L55) ......................................................................... 78
4.9.8 EMERGENCY OFF category 0; 230 V AC or 24 V DC (option L57) .......................................... 79
4.9.9 EMERGENCY STOP category 1; 230 V AC (option L59) .......................................................... 81
4.9.10 EMERGENCY STOP category 1; 24 V DC (option L60) ............................................................ 82
4.9.11 25 kW braking unit (option L61/L64); 50 kW braking unit (option L62/L65)................................ 83
4.9.11.1 Installing the braking resistor ...................................................................................................... 83
4.9.12 Thermistor motor protection unit (option L83/L84)...................................................................... 89
4.9.13 PT100 evaluation unit (option L86) ............................................................................................. 89
4.9.14 Insulation monitor (option L87) ................................................................................................... 91
4.9.15 Communication Board Ethernet CBE20 (option G33) ................................................................ 93
4.9.16 CBC10 CAN Communication Board (option G20) ...................................................................... 95
4.9.17 SMC10 Sensor Module Cabinet-Mounted (option K46) ............................................................. 98
4.9.17.1 Description .................................................................................................................................. 98
4.9.17.2 Connection .................................................................................................................................. 99
4.9.17.3 Connection example ................................................................................................................. 100
4.9.18 SMC20 Sensor Module Cabinet-Mounted (option K48) ........................................................... 102
4.9.18.1 Description ................................................................................................................................ 102
4.9.18.2 Connection ................................................................................................................................ 103
4.9.18.3 Connection example ................................................................................................................. 104
4.9.19 SMC30 Sensor Module Cabinet-Mounted (option K50) ........................................................... 106
4.9.19.1 Description ................................................................................................................................ 106
4.9.19.2 Connection ................................................................................................................................ 111
4.9.19.3 Connection examples................................................................................................................ 113
4.9.20 Voltage Sensing Module for determining the actual motor speed and the phase angle
(option K51)...............................................................................................................................
114
4.9.21 Customer terminal block extension (option G61)...................................................................... 114
4.9.22 Terminal module for activation of "Safe Torque Off" and "Safe STOP 1" (option K82)............ 115
4.9.23 NAMUR terminal block (option B00) ......................................................................................... 116
4.9.24 Electrically separate 24 V DC power supply for NAMUR (option B02)..................................... 118
4.9.25 Outgoing section for external auxiliary equipment for NAMUR (option B03)............................ 118
5 Commissioning ...................................................................................................................................... 119
5.1 Chapter content......................................................................................................................... 119
5.2 STARTER commissioning tool.................................................................................................. 121
5.2.1 Installing STARTER .................................................................................................................. 122
5.2.2 The STARTER user interface ................................................................................................... 122
5.3 Procedure for commissioning via STARTER............................................................................ 123
5.3.1 Creating a project...................................................................................................................... 123
5.3.2 Configuring the drive unit .......................................................................................................... 132
5.3.3 Starting the drive project ........................................................................................................... 160
5.3.4 Connection via serial interface.................................................................................................. 161
5.4 The AOP30 operator panel ....................................................................................................... 164