FREEWAVE FUSION USER MANUAL
INTRODUCTION Thank you for choosing the Vello FreeWave Fusion Wireless Shutter/Flash/Grouping Remote. This device triggers off-camera lights remotely from up to 300 feet away. With its multiple groups feature, you can easily configure up to three different light groups, which can be triggered individually or simultaneously, for a total of seven different combinations. (Simultaneous triggering of multiple light groups requires additional FreeWave Fusion Receivers available for purchase separately.
KEY FEATURES 2.4 GHz Radio Frequency: Reduced interference and improved wireless signal quality. Extended Range: up to 100 m (320 ft.) Multi-Purpose: Use as an individual or group wireless flash trigger, and/or as a shutter release remote trigger. Multiple Groups: Configure up to three different light groups and up to seven different group combinations.
COMPATIBLE DEVICES We recommend using a fully manually controlled flash with this device. Since the FreeWave Fusion does not transmit TTL settings, you will need to set the power output manually. The FreeWave Fusion is compatible with most cameras, flash units and studio lights. However, for flash wake-up functionality and/or high shutter speeds, you will need full TTL support via your camera, flash and FreeWave Fusion trigger.
SAFETY WARNINGS • There are no user-serviceable parts inside the devices. Do not attempt to disassemble or perform any unauthorized modification. • Do not operate the FreeWave Fusion in the presence of flammable gas or vapors. • Do not handle with wet hands or immerse in or expose to water or rain. Failure to observe this precaution could result in fire or electric shock. • Keep out of the reach of children. This device contains small parts which may pose a choking hazard.
FEATURES DIAGRAM Confirmation LED Confirmation LED Transmitter Power (Group) Switch Shutter Release Button Receiver Group Indicator Hot Shoe Mount Power Switch / Setting Button 2.
GETTING STARTED Set the DIP switch located in the battery compartment of the Transmitter and Receiver. The DIP switches set a different radio frequency for each Transmitter/Receiver set, so that multiple sets of the FreeWave Fusion and/or additional Fusion Receivers can be used simultaneously. You can use a pen to set the DIP switches to your desired code. Any combination will work so long as the switches are set identically in both the Transmitter and Receiver(s) of a single FreeWave Fusion set.
POWERING UP Turn on the Receiver: Turn on the Transmitter: Slide the Group Switch to either A, B, or C and the unit will power up. The LED will flash red at 2 second intervals to indicate that the Receiver is working. Press and hold the power button for 2 seconds to power up the Transmitter. The Group Indicator light will turn on and show the currently selected group. The Group indicator light will turn off after 2 seconds and the Transmitter will enter Standby mode.
MOUNTING THE TRANSMITTER 1. With your camera and Receiver off, loosen the Transmitter’s hot shoe locking ring. 2. Insert the Transmitter’s hot shoe on the camera’s hot shoe mount. 3. Tighten the hot shoe locking ring.
MOUNTING THE RECEIVER Mount the receiver on your tripod or stand via one of the two provided mounting options: 1. Threaded socket for a standard 1/4" screw mount 2.
CONNECTING THE LIGHTS Connecting to a Flash Unit: Connecting to a Studio Light 1. Switch the flash’s locking switch to the unlock position You will need to use the included Studio Trigger Cable in order to connect the Receiver to a studio light. 2. Insert the flash’s hot shoe foot into the Receiver’s hot shoe mount 3. Switch the flash’s locking switch to the locked position 1. Plug the 2.5 mm side of the cable into the Receiver’s output jack. 2. Plug the 3.
SETTING THE GROUPS Slide the Receiver’s Group/Power switch to either A, B, or C. To assign multiple Receivers to the same flash group, simply select the same group letter for each Receiver in the flash group. The LED at the top of the Receiver will flash red to confirm that the power is on. Tip: You can combine studio lights and speedlights within the same flash group. (Be aware of the independent recycling time of each flash to ensure all flash units are ready to fire).
SELECTING THE GROUPS 1. Gently press the Group/Power button on the Transmitter. The group indicator LED(s) will light up to indicate which groups are currently selected. 2. To change group selections, press the Group/Power button again. Keep pressing the Group/Power button to cycle through all the Group options: A only; B only; C only; A and B; A and C; B and C; A, B and C. 3. To see which groups are currently selected at any time, gently press the Group/Power button.
USING THE FLASH TRIGGER 1. Confirm that the power on your Camera, Transmitter and Receiver is turned on. 2. Press the shutter button on the camera halfway to wake your flash (if your flash has a wake-up function). 3. If your flash does not have a wake-up function, you may be able to turn off sleep mode. Refer to your flash’s manual for instructions. 4. Fully press the shutter button on your camera. All lights connected to Receivers in the currently selected group will fire.
USING THE FREEWAVE FUSION AS A REMOTE SHUTTER RELEASE Connecting the Camera: In order to use the remote shutter release function, you will need to use the included Fusion shutter release cable. 1. Plug the 2.5 mm side of the cable into the Receiver. 2. Plug the other side of the cable into your camera’s shutter release terminal. 3. Mount the Receiver on your camera’s hot shoe, facing forwards or backwards.
REMOTE SHUTTER RELEASE | SINGLE SHOTS 1. Turn on the Receiver by sliding the Group/Power switch to any position other than Off. 2. Set your camera to the single shot setting. 3. Press and hold the Transmitter’s shutter release button halfway to wake or focus your camera (if set to Auto Focus). The LED will turn green. 4. Fully depress the shutter button on the Transmitter. The LED will turn red and the shutter will be triggered.
REMOTE SHUTTER RELEASE | CONTINUOUS MODE 1. Turn on the Receiver by sliding the Group/Power switch to any position other than Off. 2. Set your camera to the continuous Shooting mode. 3. Press and hold the Transmitter’s shutter release button halfway to wake or focus your camera (if set to Auto Focus). The LED will turn green. 4. A full press of the Transmitter’s shutter button will trigger the camera to take continuous photos until you release the shutter button.
REMOTE SHUTTER RELEASE | SELF-TIMER MODE 1. Turn on the Receiver by sliding the Group/Power switch to any position other than Off. 2. Set your camera to the delay/self-timer setting. 3. Press and hold the Transmitter’s shutter release button halfway to wake or focus your camera (if set to Auto Focus). The LED will turn green. 4. Fully depress the shutter button on the Transmitter. The LED will turn red and the shutter will be triggered after a preset delay as set by your camera.
REMOTE SHUTTER RELEASE | BULB MODE (LONG EXPOSURE) 1. Turn on the Receiver by sliding the Group/Power switch to any position other than Off. 2. Set your camera to the bulb setting. 3. Press and hold the Transmitter’s shutter release button halfway to wake or focus your camera (if set to Auto Focus). The LED will turn green. 4. Press and hold the Transmitter’s shutter button. The shutter will remain open until you release the shutter button.
SPECIFICATIONS Power Battery Life* DIP Switch Settings Range Transmitter Receiver 1 CR-2032 2 AAA 3 Years 300 Hours 16 possible codes Approx. 320' (100 m) with no obstructions Frequency 2.4 GHz Confirmation LEDs 2 Color * In standby mode.
TROUBLESHOOTING Problems with the FreeWave Fusion can usually be traced to common causes. Perform the following steps to diagnose and correct the problem: Make sure that the Receiver is powered on and at the correct setting. Check the contact between the light’s hot shoe foot and the Receiver’s hot shoe. Make sure the light’s locking switch is set to the lock position.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
ONE-YEAR LIMITED WARRANTY This VELLO product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
www.vellogear.com All other trademarks are the property of their respective owners.
