BG-N16 BATTERY GRIP Designed for the Nikon D5500 and D5600 DSLR Cameras
Introduction Congratulations on your new BG-N16 battery grip purchase. Enjoy the many benefits that a battery grip offers, such as extended shooting time and more control and comfort when shooting in a vertical (portrait) orientation. The Vello BG-N16 is compatible with the Nikon D5500 and D5600 DSLR cameras, and accepts up to two Nikon EN-EL14 or EN-EL14a rechargeable batteries (not included).
4. The battery level may not display properly if batteries are mounted before mounting the grip. 5. 6. 7. Remove batteries from the grip when not in use. 8. Keep out of reach of children. devices specified in this manual. 2. Use only with batteries recommended in this manual. 3. If you notice smoke, an unusual smell or noise from the battery pack, discontinue use immediately. Remove the batteries and take the device to a Vello authorized reseller. 3 Do not attempt to disassemble.
Overview 10 11 9 5 1 2 3 4 6 7 4 8 12
1/4"-20 Tripod Socket Allows for mounting to a tripod when the grip is attached to your camera. 3 4 Anti-Slip Rubber Grip Provides a secure and comfortable grip when shooting vertically. 6 2.5 mm Remote Cable Socket Accepts 2.5 mm shutter release cable. 11 1/4"-20 Mounting Stud Connects to the camera’s tripod socket. 7 Battery Chamber Cover Secures up to two Nikon EN-EL14 or EN-EL14a batteries. 8 Battery Chamber Lock Locks the battery chamber cover. 12 2.
Attaching the Grip 1. Ensure that the camera power is turned off. 2. Turn the camera upside down and open the camera’s battery chamber door. Pull gently at a 45° angle until the chamber door detaches. 6 3. Slide the camera battery chamber door into the BG -N16 chamber door holder for safekeeping.
INTRODUCTION 5. Rotate the locking wheel counterclockwise until it is firmly tightened. 7 6. Connect the shutter release cable from the cable release socket on the battery grip to the remote release port on the camera body. OVERVIEW Inser t the BG-N16 grip power contacts into the camera’s battery chamber as shown. Make sure to align the camera’s tripod socket with the BG-N16 mounting screw. ASSEMBLY 4.
Inserting Batteries 1. Flip the battery chamber lock up and twist it counterclockwise to open the battery chamber door. 2. Line up the contacts on the batteries with the contacts inside the battery chamber. 8 3. Inser t batteries into the battery chamber. When installing two batteries, wait for the confirmation LED on the back of the camera to blink before inserting the second battery.
INTRODUCTION 5. Turn the bat ter y grip’s On/Off Switch to the On position. 9 When removing the grip, turn the camera power off and remove the batteries. OVERVIEW Close and lock the battery chamber door. ASSEMBLY 4.
Specifications Power Source Two Nikon EN-EL14 or EN-EL14a Rechargeable Batteries Operating Temperature 32°F - 104°F (0°C - 40°C) Dimensions 4.9 " × 3.1" × 3.8 " (12.4 × 7.9 × 9.6 cm) Weight 5.4 oz. (153.1 g) Troubleshooting The shutter release button on the battery grip is not triggering the camera. • • Make sure the 2.5 mm Shutter Release Cable is connected from the battery grip to the camera. Make sure the battery grip’s On/Off switch is turned on.
ONE-YEAR LIMITED WARRANTY This VELLO product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
www.vellogear.
