User Manual

ManualsBrandsVELLEMAN ManualsAssembly Kits & Modules10-Channel Light Effect Generator Assembly kit

Total solder points: 293

Difficulty level:

beginner 1o 2o 3þ 4o 5oadvanced

K8044

12V, Ten channel light

effect generator

ILLUSTRATED ASSEMBLY MANUAL H8044IP-1

þ Ten, 12V/400mA outputs.

þ To control cold-cathode fluorescent lamps (using FLPS adapter), light

bulbs, LED’s and “solid state” relays, ...

þ For use as advertisement lighting, party lights, discos, eye-catcher,...

þ Ten pre-programmed light patterns selectable with a push button.

þ The number of used channels is adjustable.

þ Adjustable speed.

þ Led indication for every output.

þ 12V operation possible for use in cars.

Specifications :

• Power supply : 12V DC

• Outputs : 12V DC/400mA per channel (Total : max 4A)

• Dimensions : 140 x 100 x 27mm / 5,5 x 3,9 x 1,1”

Options (Velleman ordernumbers) :

Ú Power supply for cold-cathode fluorescent lamps : FLPS (300mm) or

FLPS1 (100mm)

Ú Cold-cathode fluorescent lamps : FL(xx) – (100 or 300mm).

Modifications reserved.

Features:

Summary of content (16 pages)

PAGE 1
Total solder points: 293 Difficulty level: beginner 1o 2o 3þ 4o 5oadvanced 12V, Ten channel light effect generator Features: K8044 þ Ten, 12V/400mA outputs. þ To control cold-cathode fluorescent lamps (using FLPS adapter), light þ þ þ þ þ þ bulbs, LED’s and “solid state” relays, ... For use as advertisement lighting, party lights, discos, eye-catcher,... Ten pre-programmed light patterns selectable with a push button. The number of used channels is adjustable. Adjustable speed.
PAGE 2
VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.
PAGE 3
Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (2540W) with a small tip. • Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip, and enables you to make good connections.
PAGE 4
Assembly hints 1.
PAGE 5
Rosso Aranciato Laranja Giallo Verde Blu Viola Grigio Bianco Argento Oro 2 3 4 5 6 7 8 9 A B Dourado Prateado Branco Cinzento Violeta Azul Verde Amarelo Punainen Ruskea Musta VÄRI KOODI SF Oro Plata Blanco Gris Morado Azul Verde Amarillo Kulta Hopea Valkoinen Harmaa Purppura Sininen Vihreä Keltainen Naranjado Oranssi Encarnado Rojo Castanho Marrón Negro Marrone 1 Preto Nero 0 E CODICE CODIGO CODIGO COLORE DE CORES DE COLORES P C O D E I 4K7= ( 4 - 7 - 2
PAGE 6
Construction 1. Jumper q CH... : depending on the number of channels q RX ‘∗’ ‘∗’ATTENTION : In case you use light bulbs, Cold-Cathode fluorescent lamps & “solid-state” relays mount for RX a jumper wire, If using LED’s as output indication then mount for RX a resistor appropriated to the value of the LED. See step 2. 2. Resistors ‘RX’ q RX (for each output) R...
PAGE 7
Construction 3. Resistors R...
PAGE 8
Construction 5. Pushbuttons. 8. LED. Watch the polarity ! COLOR= 2...5 LD... CATHODE q SW1 : S500 q SW2 : S500 6. Voltage Regulator. VR... q VR1: UA78L05 7. IC socket, Watch the position of the notch! q q q q q q q q q q q LD1 LD2 LD3 LD4 LD5 LD6 LD7 LD8 LD9 LD10 LD11 : 5mm Red : 5mm Red : 5mm Red : 5mm Red : 5mm Red : 5mm Red : 5mm Red : 5mm Red : 5mm Red : 5mm Red : 5mm Red 9.Ceramic Capacitors C...
PAGE 9
Construction 10. Transistors. 11. Electrolytic capacitors. Watch the polarity ! C ... q q q q q q q q q q q q q q q q q q T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 q T19 q T20 : BC640 : BC640 : BC640 : BC640 : BC640 : BC640 : BC640 : BC640 : BC640 : BC640 : BC547B : BC547B : BC547B : BC547B : BC547B : BC547B : BC547B : BC547B : BC547B : BC547B q C5 : 10µF q C3 : 220µF q C1 : 1000µF / 25V 12.
PAGE 10
Construction 13. Terminal block connectors 14. Fuseholder + Fuse F... 10 SK ... 10 SK ... 1 SK 1 SK q q q q q q q q q q SK1 SK2 SK3 SK4 SK5 SK6 SK7 SK8 SK9 SK10 : CH1 : CH2 : CH3 : CH4 : CH5 : CH6 : CH7 : CH8 : CH9 : CH10 q F1 : 4A (slow) (2p) (2p) (2p) (2p) (2p) (2p) (2p) (2p) (2p) (2p) 15.
PAGE 11
Hook-up diagram 16. Hook-up diagram Inverter FLPS UT NP VI 2 1 12VDC/400mA per channel ulb .
PAGE 12
Connection 17. Use Connect this kit according to the wiring diagram. LED LD1 will light if the operating voltage is correct. Take all necessary precautions to avoid electroshocks when connecting cold-cathode fluorescent lamps : the inverter ‘FLPS1’ uses a potentially life-threatening voltage. F This kit is available in various countries. Take care to use an appropriate connection or adapter. Selecting a light effect : Push button SW1 ‘Effect select’ allows you to choose one of ten available programmes.
PAGE 13
PCB 18. PCB layout.
PAGE 14
GND D12 1N5404 GND C7 100pF R32 3K3 RV1 100K C2 GND C3 220µ R31 47 C4 100n GND SW2 S500 SW1 S500 GND O R34 10K I VR1 UA78L05 R33 10K GND D11 1N4007 EFFECT SELECT 100n GND 1000µ/25V GND EFFECT SPEED GND C1 GND SK11 +12V DC 15 16 2 1 OSC2/CLKOUT OSC1/CLKIN RA3 RA2 IC1 GND C6 100n PIC16C58B GND C5 10µ 14 VDD 4 MCLR RA4/T0CK I 18 17 13 12 11 10 9 8 7 6 LD11 LED5RL "POWER" J10-10CH J9-9CH J8-8CH J7-7CH J6-6CH J5-5CH J4-4CH J3-3CH J2-2CH J1-1CH G
PAGE 15
PAGE 16
VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Modifications and typographical errors reserved © Velleman Components nv.