K8018 ILLUSTRATED ASSEMBLY MANUAL H8018IP’1 R K8018W R K8018B 3D LED CUBE 5x5x5 K8018B (Blue LED) K8018W (White LED) Connect to your computer and create your own 3D LED effect.
Subscribing our newsletter?, visit www.vellemanprojects.
Build your 3D led cube and created unlimited 3D effects. The unit comes standard loaded with effects.
nit Leds and how to use them Leds feature a specific voltage drop, depending on type and colour. Check the datasheet for exact voltage drop and rated current ! Never connect leds in parallel How to Calculate the series resistor: Example: operate a red led (1.7V) on a 9Vdc source. Required led current for full brightness: 5mA (this can be found in the datasheet of the led) Supply voltage (V) - led voltage (V) = series resistance (ohms) required current (A) closest value : use a 1k5 resistor 9V - 1.
assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (25-40W) with a small tip. • Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip, and enables you to make good connections.
DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE.
Construction SK1 SPEED 1 MODE VR1 R10 R11 SW2 SW1 D1 1x3mm C13 R4 T1 IC1 C1 IC1: 28p SK2 R5 R6 R7 C9 C6 T4 C14 R9 C10 D2 T3 C2 C3 C8 D3 R3 LD1 USB ONLY 3 SMD IC 7 LED Watch the position of the notch! 11 COLOR= 2...5 R8 T5 C7 R2 C11 C12 X1 C5 PLANE1 PLANE2 PLANE3 PLANE4 PLANE5 COL5.2 COL5.1 COL5.3 COL5.5 COL5.4 COL4.1 COL4.3 COL4.2 COL4.4 C4 IC2 COL4.5 LD... IC3 R1 Watch the polarity! SK4 COL3.3 COL3.4 COL3.5 COL2.1 COL2.
Construction 10 Female Header 14 Electrolytic capacitors P8018 - BOTTOM Watch the polarity! MOUNT ON TOPOVERLAY SIDE C... 8p C9 C13 C14 C1 .. J. .. J. SK4 : 30pins 11 Transistors : 4,7µF : 100µF : 10µF : 470µF 15 Voltage regulator .. J. RED C4 COL1.1 COL1.2 COL2.3 COL2.4 COL2.5 COL2.1 COL2.2 COL5.2 COL3.4 COL3.5 PLANE5 COL5.1 PLANE3 PLANE4 COL3.3 PLANE2 COL3.1 COL3.2 PLANE1 C5 R2 IC3 SK4 -8- COL5.4 IC1: VK8018 (programmed PIC18F27J53ISP) A COL5.
Construction Assembly of the LEDs Step Step 2 x 20 Solder ! Bend View the assembly movie of MK193 as guideline for assembly of the LEDs. Step 1 x 100 COLOR= 2...5 LD...
Construction Step 4 x1 Step 5 x 25 + 2mm C Bend a Bend So Solder ld Step 6 er x5 Solder A - 10 - ! Bend
Construction Step 7 x1 x1 Step 8 So Step ld er C Solder CUT ! - 11 - C
Construction Step 9 Step 11 Step 10 Solder - 12 -
PCB Software Donwload the LEDcube software on our website www.velleman.eu For software, visit www.vellemanprojects.eu Help instructions Create, edit or remove your own animation Choose 5x5 to send or read the animations of your 5x5x5 LED cube.
PCB - 14 -
Diagram VR1 LM317 I SW 1N4007 C1 C2 +5V R10 470 C3 100n 470µ-25V - DC JACK D2 O 1N4007 D3 100n D1 + ADJ SK3 +5Vpic 1N4007 +5V GND GND GND GND 100µ/16-25V R11 1K1 PLANE1 PLANE2 LD1 LED3RL R4 PLANE3 39 0 C13 COL1.1 COL1.1 COL1.2 COL1.2 COL1.3 COL1.3 COL1.4 COL1.4 GND PLANE4 GND T1 BC640 PLANE5 COL1.5 COL1.5 COL2.1 COL2.1 COL2.2 COL2.2 COL2.3 COL2.3 COL2.4 COL2.4 COL2.5 COL2.
The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu Modifications and typographical errors reserved - © Velleman nv. H8018’IP Velleman NV, Legen Heirweg 33 - 9890 Gavere.
