3-PERSON 2-IN-1 CONVERTING PATIO SWING WITH CANOPY
STOP MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE The store where you made your purchase Does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts,please call 1-858-324-1911 (Mon - Fri, 10:00 am to 7:00 pm EST) you can also e-mail customerservice@veikous.com or visit www.veikous.com Please prefer email contact. Due to busy lines, there may be a wait for calls to be answered.
HARDWARE LIST M8X100 Bolt 2PCS M8X98 Bolt 4PCS M6X60 Bolt 6PCS M6X32 Bolt 6PCS M6X40 Bolt 4PCS M6X35 Bolt 4PCS M6X30 Bolt 2PCS Nut cover 24PCS 11 12 2PCS 2PCS 14 13 1PC M8X75 Bolt 2PCS 1PC 2PCS
PARTS LIST X1 X2 X2 X1 G X2 X1 H I X1 J X1 X1 K L x X1 M X4 O N X2 X1 X2 P X1 X3 C
Step1 Assembling the swing frame 1. Attach the shorter leg(B) and the longer leg(C) on one side as shown below, and put one bolt(1)on the first top hole, two bolts(2) on the bottom two holes and then fasten all of them by using three nuts(9) at back. 2. Repeat the step to make sure you have the entire swing frame assembled ready on both sides.
Step2 Assembling the swing frame support 1.Attach the support bar(E) in between to the legs(C) (the back of the swing), and then fasten it by using one bolt(4) and one nut(9) ONLY at the bottom hole on each side.(DO NOT do with the top hole now) 2.Attach two side bars(D) in between the leg(B) and leg(C) on both sides with four bolts(4) and four nuts(9). Now you can fasten the top holes of bar(E) by putting the bolt(4) across side bar(D) as shown below.
Step3 Assembling the swing frame support Attach the bottom supporting bar(F) in between to the two side bars(D) with two bolts(8)and two nuts(9).
Step4 Assembling the seat frame 1.Insert the front bar(G) and rear bar(H) into the arm(J) and the arm(I), and then connect them with four bolts(6) and four nuts(9). 2.Attach the four swing pipes(K) to the arm(J) and the arm(I) using four bolts(5) and four nuts(9). 3.Connect the top of the two swing pipes using the spring hooks (10). Back Front Install bar(H) on the back side where is shorter between the holes.
Step5 Assembling the seat Connect the seat(L) to the arm(I) and arm(J) on both sides with two bolts(3), two nuts(9) and two plastic gaskets(11) as shown below. The seat(L) support rod is stuck in the rear bar(H) buckle to hold the seat in place.
Step6 Assembling the canopy 1 Place the two supporting bars(N) across the canopy(O) as shown below.
Step7 Assembling the canopy 2 1.Connect the bar(N) to the curved bar(M) with three bolts(7). 2.Repeat the step twice to make sure you get the whole canopy frame assembled.
Step8 Assembling the canopy 3 1.Place the canopy(O) on the assembled top frame.Attach the top frame to the top bar using the screw knobs(12) on both sides.
Step9 Attaching the seat to the swing frame 1.Attach the assembled seat to the swing frame using the two spring hooks(10). 2.Place the three seat cushions(P) on the seat.
The product can be used in 2 ways 10 Patio swing as normal with upright backrest. 1 2 Laying down as a swing bed with the back fixed to the rear supporting bar.
Enjoy your product！ Note 1. Adjust the angle of the top frame and fully tighten the screw knobs for everytime you adjust the canopy. 2. Make sure to fix all cushions to the seat using ties in case they are blew away by wind. Care and Cleaning 1.For best results, clean the swing with a damp cloth and dry thoroughly. This will help prevent mildew by removing dirt particles that may accumulate. 2.Do not clean with abrasive materials, bleach, or solvents. 3.
