STOP MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE The store where you made your purchase Does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts,please call 1-858-324-1911 (Mon - Fri, 10:00 am to 7:00 pm EST) you can also e-mail customerservice@veikous.com or visit www.veikous.com Please prefer email contact. Due to busy lines, there may be a wait for calls to be answered.
F C E1 N2 N1 D2 A E N F N2 Y L1 L H N1 N 2 D1 N2 L N1 N2 M 1 D J K 3 U Pg.
HARDWARE P3 P1 P1 P3 P4 M6X70 M6X70 Bolt M6X15Bolt Bolt M6X15 Bolt 106 PCS O P4 R P3 P4 M6X70 M6X70 Bolt Bolt M6X40 Bolt 66PCS M6X40 Bolt 66PCS 80 PCS 1 PC 1 PCS Big Bolt Tool Nut Cap M6X40 Bolt 66PCS 113 PCS PC 1 1PCS M6 Bolt Tool 1 PC 1 PC Plastic Bolt Cap M6X70 M6X70 Bolt 1 PC 1 PC PARTS D3 1 PC 1 10 PCS Enhanced support beam connector 2 PCS N2 H Bottom cross beam connector 1 PC 4 PCS Triangle cap 4 PCS Pg.
R R R Attach post top cap (A) to post (1 & 2) R R R Attach and fasten stake piece (U) to the end of post (3) by bolt (P1) and cap (R) Insert post connector (J) into post (3) by bolt (P1) and bolt cap (R) R R R Attach decorative circle (K) to post (3), and attach post (1 & 2) to post (3) by bolt (P1) and bolt cap (R) P1 R P1 R Connect two middle cross beams (C) with inside connector (N1) by bolt (P1) & bolt cap (R) to make sure that there is no gap between the two middle cross beams (C) by tig
P4 Attach triangle cap (G) to assembled middle cross beam (C) R R P1 P1 Assemble six side glidewheels (M) into side cross beam (E), and then connect side cross beam 1 (E) & side cross beam 2 (E1) with inside connector (N1) by bolt (P1) & bolt cap (R) to make sue there is no gap between the two tubes by tighting the bolt Attach triangle cap (G) to side cross beam 1 & 2 (E & E1) R P1 R P1 R P1 v D3 Connect bottom cross beam 1 (D) and bottom cross beam 2 (D1) & beam3(D3) with inside connector (N2) b
R P1 R P1 Connect two enhanced support beams (F) with inside connector (N2) by bolt (P1) & bolt cap (R) to make sue there is no gap between the two tubes by tighting the bolt Attach triangle cap (G) to assembled enhanced support beam (F) Connect assembled side cross beam ( E1) and assembled bottom cross beam 2 (D1) to assemled post (2) by big bolt (P2) --- ----- ---------- D3 Follow the same step as 14 to connect other three left Pg.
P3 P3 R R P3 R D3 P4 Attach assemled middle cross beam (C) to assembled bottom cross beam (D & D1 & D2) by bolt (P3) & bolt cap (R) 19 P3 R R F P3 F P3 R F F P3 R Attach assembled enhanced support beam (F) to assembled bottom cross beam (D & D1) by bolt (P3) & bolt cap (R) 20 Insert fabric rib 1 (L) into fabric rib 2 (L1), and then through assembled fabric rib 1 (L) into fabric cover (W), and through assembled fabric rib1 (L) into the hole of glidewheel (Y&B)which on assembled middle cro
21 D3 P1 R M 22 D1 D3 D 23 D3 D3 D T D1
Enjoy your product! Care and Cleaning 1.For best results, clean the pergolas with a damp cloth and dry thoroughly. This will help prevent mildew by removing dirt particles that may accumulate. 2.Do not clean with abrasive materials, bleach, or solvents. 3.Store the pergolas in a dry, sheltered place when not in use. 4.Keep the pergolas away from fire, extreme heat, freezing conditions, and inclement weather such as rain, hail, sleet, snow, or wind.
