User's Manual

WaveCom Electronics Inc
MA4061/MA4070 Manual; MAN1L2301 Rev03 (Mar 2002)
Approved: R. L.
11
3.0 OPERATION
3.1 Front Panel Description
D
DD
DIAGRAM
IAGRAM IAGRAM
IAGRAM 3.1
3.13.1
3.1A
A A
A : F
: F: F
: FRONT
RONT RONT
RONT P
PP
PANEL
ANEL ANEL
ANEL –
––
– MA4200 S
MA4200 S MA4200 S
MA4200 SYSTEM
YSTEMYSTEM
YSTEM
As shown in Diagram 3.1A, the power/control module front panel has an LCD display, four soft touch push
buttons, and 4 indicator LEDs. All other modules have 4 indicator LEDs. Modules are configured using push
buttons on the power supply module, or via the remote interface. If no configuration adjustments are being
made via the front panel controls, the display back light will shut off after a five minute time out. Pressing any
of the front panel buttons will re-enable the back light.
3.1.1 MA4010B Power/Control Module
D
DD
D
IAGRAM
IAGRAM IAGRAM
IAGRAM 3.1
3.13.1
3.1B
B B
B : F
: F: F
: FRONT
RONT RONT
RONT P
PP
PANEL
ANEL ANEL
ANEL –
––
– MA4010B
MA4010B MA4010B
MA4010B
DISPLAY
The first line on the display
is the Mode Information Line. It shows the settings for the currently selected
module. The possible operating modes depend upon the currently selected module (See Section 3.2, Front
Panel Operating Modes (pp 15 to 17) for a detailed description of the available modes).
The second line on the display
is the Status Information Line. The Status Line is divided as follows:
The two leftmost characters are “mX” where X is replaced by the currently selected module address. The
module addresses are assigned starting with module A in the leftmost slot in the chassis and module K in the
Power Supply. The modules in between are lettered B through J. When used with the MA4070B Power Amp
Modules, the MA4061B Upconverter Modules can only be installed in slots A and F. The MA4070B Power
Amp Modules can only be installed in slots B thru E and slots G thru J (as shown in Diagram 3.1A).
The next two characters are “sXX” where “XX” indicate the status code for the currently selected module.
Refer to Section 5.0, Status Codes (pp 23 to 25) for a list of current status codes.
The next two characters are “eXX” where “XX” indicates the error code for the currently selected module.
(This code is only displayed when it is non-zero). Refer to Section 6.0, Error Codes (pp 27 to 29) for the list of
current error codes.
A
B C D E F G H I J K
MMD
S
POWER AM PLIFIE
R
WaveCom M A4070B
DC
POWE
R
RF
HIGH
A
LAR
M
RF
LOW
A
LAR
M
HIGH
REV
POWE
R
A
LAR
M
UNI
T
SELE C
T
MMD
S
POWER AM PLIFIE
R
WaveCom M A4070B
DC
POWE
R
RF
HIGH
A
LAR
M
RF
LOW
A
LAR
M
HIGH
REV
POWE
R
A
LAR
M
UNI
T
SELEC
T
WaveCom
MA4061B
POWE
R
MODUL
E
SELEC
T
A
LAR
M
MMDS DIGITAL
UPCONVERTER
RF
ENABLED
Wave Com
MA4061B
POWE
R
MODUL
E
SELE C
T
A
LAR
M
MMDS DIGITAL
UPCONVERTE
R
RF
ENABLED
POWE
R
A
LAR
M
MODUL
E
SELE C
T
A
U
X
DOW
N
UP
MODUL
E
SELEC
T
MOD
E
WAVECOM
ELECTRONICS INC
SYSTEM 4000
POWER SUPPLY
WaveCom M A4010B
POWE
R
A
LAR
M
MODUL
E
SELEC
T
A
U
X
DOW
N
UP
MODUL
E
SELEC
T
MOD
E
WAVECOM
ELECTRO NICS INC
SYSTEM 4000
POWER SUPPLY
WaveCom MA4010B