User's Manual

ManualsBrandsVecima Networks ManualsElectronicsWireless LAN end-user modem

100

Table Of Contents

Contents
- Contents v
- Figures ix
- Tables xi
- Preface xv
- Index 261
Figures
Tables
Preface
- About this Manual
- Conventions
- Regulatory Notices
- Warnings and Advisories
- Customer Support
1 Introduction
2 Quick Startup
- 2.1 Equipment
- 2.2 Equipment Setup
- 2.3 CCU Configuration
- 2.4 EUM Configuration
- 2.5 Testing CCU–EUM Communications
- 2.6 Connecting the Quick Startup to the Internet
- 2.7 Adding more EUMs to the Quick Startup
3 Detailed Description
- 3.1 LMS4000 Overview
- 3.2 Communications Access Point
  - 3.2.1 Key Components
  - 3.2.2 Optional Components
- 3.3 Customer-premises Equipment
  - 3.3.1 Key Components
  - 3.3.2 EUM
- 3.4 Basic Operation
- 3.5 CCU–EUM Interface — Detailed Technical Description
  - 3.5.1 Physical Layer (DSSS Radio)
  - 3.5.2 MAC Layer (Polling MAC)
- 3.6 CCU and EUM Feature Description
4 IP Network Planning
- 4.1 LMS4000 IP Addressing
- 4.2 IP Planning Process
- 4.3 Network Address Translation
5 Radio Network Planning
- 5.1 Design Methodology
- 5.2 Basic System Design
- 5.3 Multi-CAP RF Network Design Considerations
6 Installation/Diagnostic Tools
- 6.1 Indicators and Connectors
- 6.2 Command-line Interface
- 6.3 EUM Configuration Utility
- 6.4 RSSI/Tx Quality/Antenna Pointing
- 6.5 Transfer a File to or from a CCU Using FTP
- 6.6 Operating Statistics
- 6.7 SNMP
- 6.8 Field Upgrade Process
- 6.9 FTPing CCU and EUM Configuration Files
7 Configuring the CCU
- 7.1 CCU and EUM Serial Number, MAC Address, and Station ID
- 7.2 Setting the CCU Password
- 7.3 Configuring the CCU RF Parameters
- 7.4 Configuring CCU IP Parameters
- 7.5 Configuring DHCP Relay
- 7.6 Configuring Port Filtering
- 7.7 Configuring the SNTP/UTC Time Clock
- 7.8 Configuring SNMP
- 7.9 Adding EUMs to the Authorization Table
8 Configuring the EUM
- 8.1 Setting the EUM Password
- 8.2 Configuring the EUM RF Parameters
- 8.3 Configuring EUM IP Parameters
- 8.4 Configuring Port Filtering
- 8.5 Configuring SNMP
- 8.6 Configuring the Customer List
9 Installing the EUM
- 9.1 Before you Start the EUM Installation
- 9.2 Other EUM Programming Considerations
- 9.3 Installation Overview
- 9.4 Installation Procedures
10 Maintaining the Network
- Maintaining Temperature and Humidity
- Cleaning the Equipment
- Checking the CCU Shelf Cooling Fans
11 Monitoring the Network
- 11.1 CCU Transmit Statistics
- 11.2 CCU Receive Statistics
- 11.3 EUM Statistics Monitoring
12 Troubleshooting
- 12.1 EUM Troubleshooting
- 12.2 CCU Troubleshooting
- 12.3 If You Have an Interferer
- 12.4 General Troubleshooting Information
- Network Address Translation
- Ethernet Cable Wiring
13 Specialized Applications
- 13.1 EUM Thin Route
- 13.2 EUM Backhaul
Appendix A Specifications
Appendix B Factory Configuration
Appendix C CommandLine Syntax
- Command-line Syntax Conventions and Shortcuts
- CCU Command-line Syntax
- EUM Command-line Syntax
Appendix D Antenna Guidelines
Appendix E CCU/EUM Data Tables
Appendix F Ping Commands
Appendix G SNMP MIB Definitions
- MIB-II Elements Supported from RFC-1213
  - Groups in MIB-II
  - Interfaces Group MIB
- WaveRider CCU Enterprise MIBs
- CCU RFC MIB-II Traps
  - RFC MIB-II Traps
- WaveRider EUM Enterprise MIBs
- EUM RFC MIB-II Traps
  - RFC MIB-II Traps
Appendix H Operating Statistics
- Ethernet Statistics
- Radio Driver Statistics
- MAC Interface Statistics
- Routing/Bridging Protocol Statistics
- Network Interface Statistics
- System Load Statistics (Radio Meter)
Appendix I IP Plan — Example
- NAP IP Addressing Plan
- CCU Ethernet IP Addressing Plan
- CCU Radio IP Addressing Plan
- EUM IP Addressing Plan
- Subscriber IP Addressing Plan
Appendix J Acronyms and Glossary
Index

6 Installation/Diagnostic Tools

APCD-LM043-4.0 79

Hash mark printing On ftp: (2048 bytes/hash mark) .

ftp> binary

200 Type set to I, binary mode

ftp> get sa1110.bak

200 Port set okay

150 Opening BINARY mode data connection

############################################################################

###

############################################################################

###

##################################################################

226 Transfer complete

ftp: 463713 bytes received in 10.80Seconds 42.96Kbytes/sec.

ftp>bye

221 Bye...See you later.

4. Enter the following commands to put the sa1110.bak file to the CCU.

Connected to <aaa.bbb.ccc.ddd>.

220 FTP server ready

User (<aaa.bbb.ccc.ddd>:(none)):

331 Password required

Password:

230 User logged in

ftp> hash

Hash mark printing On ftp: (2048 bytes/hash mark) .

ftp> binary

200 Type set to I, binary mode

ftp> put sa1110.bak null

200 Port set okay

150 Opening BINARY mode data connection

############################################################################

####

############################################################################

####

##################################################################

226 Transfer complete

ftp: 463713 bytes sent in 8.30Seconds 55.86Kbytes/sec.

ftp>bye

221 Bye...See you later.

Entering null after the put command ensures the file will not be permanently stored to CCU

memory. If you inadvertently forget to enter null after the put command and save the file to

CCU memory, the throughput performance of the CCU may be reduced significantly. You can

remove the file using the CCU file services, available through the command line interface. As

long as you enter null after the put command, any size file can be used.

The FTP throughput should correspond to a value slightly less than the maximum allowed by

the GOS, assuming no other traffic is being carried by the CCU.

6.6 Operating Statistics

The CCU and EUM collect a wide range of IP, radio, MAC, and network layer statistics, which

can be used for measuring system performance and troubleshooting. These statistics can be

accessed through the command line interface, outlined in Appendix C on page 163 or by using

an SNMP manager. A list of available statistics and their meanings can be found in Appendix

Honpage223.