User's Manual

ManualsBrandsVecima Networks ManualsElectronicsWireless LAN end-user modem

Table Of Contents

Contents
- Contents v
- Figures ix
- Tables xi
- Preface xv
- Index 261
Figures
Tables
Preface
- About this Manual
- Conventions
- Regulatory Notices
- Warnings and Advisories
- Customer Support
1 Introduction
2 Quick Startup
- 2.1 Equipment
- 2.2 Equipment Setup
- 2.3 CCU Configuration
- 2.4 EUM Configuration
- 2.5 Testing CCU–EUM Communications
- 2.6 Connecting the Quick Startup to the Internet
- 2.7 Adding more EUMs to the Quick Startup
3 Detailed Description
- 3.1 LMS4000 Overview
- 3.2 Communications Access Point
  - 3.2.1 Key Components
  - 3.2.2 Optional Components
- 3.3 Customer-premises Equipment
  - 3.3.1 Key Components
  - 3.3.2 EUM
- 3.4 Basic Operation
- 3.5 CCU–EUM Interface — Detailed Technical Description
  - 3.5.1 Physical Layer (DSSS Radio)
  - 3.5.2 MAC Layer (Polling MAC)
- 3.6 CCU and EUM Feature Description
4 IP Network Planning
- 4.1 LMS4000 IP Addressing
- 4.2 IP Planning Process
- 4.3 Network Address Translation
5 Radio Network Planning
- 5.1 Design Methodology
- 5.2 Basic System Design
- 5.3 Multi-CAP RF Network Design Considerations
6 Installation/Diagnostic Tools
- 6.1 Indicators and Connectors
- 6.2 Command-line Interface
- 6.3 EUM Configuration Utility
- 6.4 RSSI/Tx Quality/Antenna Pointing
- 6.5 Transfer a File to or from a CCU Using FTP
- 6.6 Operating Statistics
- 6.7 SNMP
- 6.8 Field Upgrade Process
- 6.9 FTPing CCU and EUM Configuration Files
7 Configuring the CCU
- 7.1 CCU and EUM Serial Number, MAC Address, and Station ID
- 7.2 Setting the CCU Password
- 7.3 Configuring the CCU RF Parameters
- 7.4 Configuring CCU IP Parameters
- 7.5 Configuring DHCP Relay
- 7.6 Configuring Port Filtering
- 7.7 Configuring the SNTP/UTC Time Clock
- 7.8 Configuring SNMP
- 7.9 Adding EUMs to the Authorization Table
8 Configuring the EUM
- 8.1 Setting the EUM Password
- 8.2 Configuring the EUM RF Parameters
- 8.3 Configuring EUM IP Parameters
- 8.4 Configuring Port Filtering
- 8.5 Configuring SNMP
- 8.6 Configuring the Customer List
9 Installing the EUM
- 9.1 Before you Start the EUM Installation
- 9.2 Other EUM Programming Considerations
- 9.3 Installation Overview
- 9.4 Installation Procedures
10 Maintaining the Network
- Maintaining Temperature and Humidity
- Cleaning the Equipment
- Checking the CCU Shelf Cooling Fans
11 Monitoring the Network
- 11.1 CCU Transmit Statistics
- 11.2 CCU Receive Statistics
- 11.3 EUM Statistics Monitoring
12 Troubleshooting
- 12.1 EUM Troubleshooting
- 12.2 CCU Troubleshooting
- 12.3 If You Have an Interferer
- 12.4 General Troubleshooting Information
- Network Address Translation
- Ethernet Cable Wiring
13 Specialized Applications
- 13.1 EUM Thin Route
- 13.2 EUM Backhaul
Appendix A Specifications
Appendix B Factory Configuration
Appendix C CommandLine Syntax
- Command-line Syntax Conventions and Shortcuts
- CCU Command-line Syntax
- EUM Command-line Syntax
Appendix D Antenna Guidelines
Appendix E CCU/EUM Data Tables
Appendix F Ping Commands
Appendix G SNMP MIB Definitions
- MIB-II Elements Supported from RFC-1213
  - Groups in MIB-II
  - Interfaces Group MIB
- WaveRider CCU Enterprise MIBs
- CCU RFC MIB-II Traps
  - RFC MIB-II Traps
- WaveRider EUM Enterprise MIBs
- EUM RFC MIB-II Traps
  - RFC MIB-II Traps
Appendix H Operating Statistics
- Ethernet Statistics
- Radio Driver Statistics
- MAC Interface Statistics
- Routing/Bridging Protocol Statistics
- Network Interface Statistics
- System Load Statistics (Radio Meter)
Appendix I IP Plan — Example
- NAP IP Addressing Plan
- CCU Ethernet IP Addressing Plan
- CCU Radio IP Addressing Plan
- EUM IP Addressing Plan
- Subscriber IP Addressing Plan
Appendix J Acronyms and Glossary
Index

— This page is intentionally left blank —