Technical data

930 Keysight InfiniiVision 2000 X-Series Oscilloscopes Programmer's Guide
Index
square waveform generator output, 667
SRE (Service Request Enable
Register), 141, 766
SRQ (Service Request interrupt), 161, 165
Standard Event Status Enable Register
(ESE), 126, 771
Standard Event Status Register (ESR), 128,
770
standard for video, 626
standard, LIN, 485
start acquisition, 144, 159, 176, 178
start and stop edges, 345
start cursor, 729
start measurement, 340
start print job, 311
start time, 614, 729
start time marker, 728
state memory, 139
state of instrument, 131, 574
status, 142, 179, 181
Status Byte Register (STB), 140, 142, 143,
764
status data structure clear, 125
status registers, 60
status reporting, 759
STB (Status Byte Register), 140, 142, 143,
764
step size for frequency span, 282
stop, 159, 180
stop acquisition, 180
stop cursor, 730
stop displaying channel, 158
stop displaying math function, 158
stop displaying pod, 158
stop on mask test failure, 400
stop time, 614,
730
storage, 139
store instrument setup, 131, 139
store setup, 139
storing calibration information, 210
string variables, 58
string variables, reading multiple query
results into, 59
string variables, reading query results into
multiple, 59
string, quoted ASCII, 118
subnet mask, 42
subsource, waveform source, 653
subsystem commands, 3, 797
subtract math function, 278, 289, 649
subtract math function as g(t) source, 285
sweep mode, trigger, 589, 600
sweep speed set to fast to measure fall
time, 350
sweep speed set to fast to measure rise
time, 359
switch disable, 568
sync break, LIN, 486
syntax elements, 117
syntax rules, program data, 796
syntax, optional terms, 117
syntax, program message, 793
SYSTem commands, 563
system commands, 565, 566, 567, 568,
574, 576
system commands introduction, 564
T
tdelta, 727
tedge, 363
telnet ports 5024 and 5025, 637
Telnet sockets, 61
temporary message, 566
TER (Trigger Event Register), 181, 767
termination conditions, mask test, 396
test sigma, mask test run, 401
test, self, 145
text, writing to display, 566
threshold, 249, 415, 710, 748
threshold voltage (lower) for
measurement, 725
threshold voltage (upper) for
measurement, 732
thresholds, 345, 728
thresholds used to measure period, 355
thresholds, how autoscale affects, 153
time base, 579, 580, 581, 582, 583, 747
time base commands introduction, 578
time base reset conditions, 137, 571
time base window, 585, 586, 587
time between points, 727
time buckets, 185, 186
time delay, 747
time delta, 727
time difference between data points, 657
time duration, 614
time holdoff for trigger, 594
time interval, 363, 365, 727
time interval between trigger and
occurrence, 731
time marker sets start time, 728
time measurements with X cursors, 325
time per division, 581
time record,
284
time reference, lister, 316
time specified, 374
time, calibration, 216
time, mask test run, 402
time, start marker, 729
time, stop marker, 730
time, system, 576
time/div, how autoscale affects, 153
TIMebase commands, 577
timebase vernier, 584
TIMebase:MODE, 56
time-ordered label list, 260
timeout, SPI clock, 497
timing measurement, 340
title channels, 225
title, mask test, 410
tolerance, automask, 386, 387
top of waveform value measured, 375
total frame count (CAN), 457
total waveforms in mask test, 391
trace memory, 179
track measurements, 360
trademarks, 2
transfer instrument state, 131, 574
tree traversal rules, 797
TRG (Trigger), 141, 143, 144
TRIG OUT BNC, 211
trigger armed event register, 167, 169
trigger burst, UART, 525
trigger channel source, 615, 625
TRIGger commands, 589
TRIGger commands, general, 591
trigger data, UART, 526
TRIGger EDGE commands, 601
trigger edge coupling, 602
trigger edge slope, 605
trigger event bit, 181
Trigger Event Register (TER), 767
TRIGger GLITch commands, 607
trigger holdoff, 594
trigger idle, UART, 527
TRIGger IIC commands, 469
trigger level auto set up, 595
trigger level constants, 227
trigger level voltage, 603
trigger level, high, 596
trigger level, low, 597
TRIGger LIN commands, 479
trigger occurred, 143
TRIGger PATTern commands, 616
trigger pattern qualifier, 620
trigger qualifier, UART, 528
trigger reset conditions, 137, 571
trigger SPI clock slope, 496
TRIGger SPI commands, 493
trigger status bit, 181
trigger sweep mode, 589
TRIGger TV commands, 621
trigger type, SPI, 507
trigger type, UART, 529
TRIGger UART commands, 509
trigger, CAN, 463
trigger, CAN pattern data length, 466
trigger, CAN pattern ID mode, 468
trigger, CAN sample point, 459
trigger, CAN signal baudrate, 460
trigger, CAN signal definition, 461
trigger, CAN source, 462
trigger, edge coupling, 602
trigger, edge level, 603
trigger, edge reject, 604
trigger, edge slope, 605
trigger, edge source, 606
trigger, force a, 592
trigger, glitch greater than, 609
trigger, glitch less than, 610
trigger, glitch level, 611
trigger, glitch polarity, 612
trigger, glitch qualifier, 613
trigger, glitch range, 614