Technical data
Index
Keysight InfiniiVision 2000 X-Series Oscilloscopes Programmer's Guide 929
returning number of data points, 188
RF burst demo signal, 239
right reference, 582
ringing pulse demo signal, 238
rise time measurement, 340
rise time of positive edge, 359
RMS value measurement, 373
roll time base mode, 579
root (:) commands, 147, 150
root level commands, 3
RQL (Request Control) status bit, 127, 129
RQS (Request Service), 143
RS-232/UART triggering, 448
RST (Reset), 136
rules, tree traversal, 797
rules, truncation, 794
run, 144, 176
Run bit, 167, 169
run mode, mask test, 396
running configuration, 139, 574
Rx frame count (UART), 517
Rx source, 522
S
sample rate, 194
sampled data, 714
sampled data points, 637
SAV (Save), 139
save, 139, 427
SAVE commands, 425
save filename, 428
save image, 429
save image with inksaver, 432
save mask, 434, 435
save mask test failures, 399
save path information, 437
save reference waveform, 445
save setup, 438
save to reference waveform location, 698
save waveform data, 439
saved image, area, 746
saving and recalling data, 252
SBUS CAN commands, 452
SBUS commands, 447
SBUS<n> commands, general, 449
scale, 292, 583, 587
scale factors output on hardcopy, 299, 430
scale for channels, 234
scale units for channels, 235
scale units for external trigger, 275
scaling display factors, 227
SCPI commands, 61
SCPI.NET example in C#, 902
SCPI.NET example in IronPython, 914
SCPI.NET example in Visual Basic
.NET, 908
SCPI.NET examples, 902
scratch measurements, 726
screen area for hardcopy print, 297
screen area for saved image, 746
screen image data, 258
SEARch commands, 531
SEARch commands, CAN, 536
SEARch commands, general, 532
SEARch commands, IIC, 542
SEARch commands, LIN, 549
SEARch commands, SPI, 555
SEARch commands, UART, 559
search mode, 534
search state, 535
SECAM, 622, 626
seconds per division, 583
segmented waveform save option, 443
segments, analyze, 189
segments, count of waveform, 647
segments, setting number of memory, 190
segments, setting the index, 191
segments, time tag, 648
select measurement channel, 361
self-test, 145
sensing a channel probe, 713
sensing a external trigger probe, 717
sensitivity of oscilloscope input, 227
sequential commands, 800
serial clock, 471, 499
serial data, 472
serial decode bus, 447
serial decode bus display, 450
serial decode mode, 451
serial frame, 500
serial number, 177
service request, 143
Service Request Enable Register
(SRE), 141, 766
set center frequency, 281
set cursors, 729, 730
set date, 565
set time, 576
set up oscilloscope, 41
setting digital display, 245
setting digital label, 204, 246
setting digital position, 247
setting digital threshold, 249
setting display, 280
setting external trigger level, 271
setting impedance for channels, 223
setting inversion for channels, 224
setting pod display, 413
setting pod size, 414
setting pod threshold, 415
settings, 135, 139
settings, instrument, 296
setup, 184, 198,
219, 244, 252, 296,
574
setup configuration, 135, 139, 574
setup defaults, 136, 570
setup memory, 135
setup reported, 590
setup, recall, 422
setup, save, 438
shape of modulation signal, waveform
generator, 678
short form, 5, 794
show channel labels, 259
show measurements, 340, 360
SICL example in C, 882
SICL example in Visual Basic, 891
SICL examples, 882
sigma, mask test run, 401
signal type, 231
signed data, 632
simple command headers, 795
sine waveform demo signal, 238
sine waveform generator output, 667
single acquisition, 178
single-ended probe heads, 228
single-ended signal type, 231
single-shot demo signal, 238
single-shot DUT, synchronizing with, 786
size, 414
size, digital channels, 248
skew, 230, 711
skew reference waveform, 699
slope, 496, 605
slope (direction) of waveform, 731
slope not valid in TV trigger mode, 605
slope parameter for delay
measurement, 347
slot, network printer, 307
smoothing acquisition type, 631
snapshot all measurement, 342
software version, 130
source, 361,
462, 484
source for function, 293, 294, 718
source for trigger, 606
source for TV trigger, 625
source, automask, 384
source, mask test, 409
source, save reference waveform, 444
source, waveform, 649
span, 278
span of frequency on display, 282
specify measurement, 361
SPI, 496
SPI clock timeout, 497
SPI decode bit order, 495
SPI decode word width, 508
SPI MISO data, 653
SPI SEARch commands, 555
SPI serial search, data, 557
SPI serial search, data width, 558
SPI serial search, mode, 556
SPI trigger, 498, 504, 506
SPI trigger clock, 499
SPI trigger commands, 493
SPI trigger frame, 500
SPI trigger MISO data pattern, 503
SPI trigger MOSI data pattern, 505
SPI trigger type, 507
SPI trigger, MISO data source, 501
SPI trigger, MOSI data source, 502
SPI triggering, 448
square wave duty cycle, waveform
generator, 671