English page 1-18 GB C10WL Deutsch Seite 19-38 D C10WL Français page 39-56 F C10WL Italiano pagine 57-74 I C10WL Español pagina 75-92 E C10WL Nederlands pagina 93-110 NL C10WL
ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1,75 20x1,75 24x1 3/8 24x1,75 26x1 26x1,5 26x1,6 26x1,75 26x1,9 26x2,00 26x2,125 26x1 3/8 26x3/4 WS in mm KMH WS in inch MPH 1272 1590 1948 1907 1973 2026 2051 2070 2089 2114 2133 2105 1954 50,1 62,6 76,7 75,1 77,7 79,8 80,7 81,5 82,2 83,2 84,0 82,9 76,9 ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1,5 28x1,75 28x1 1/2 28x1 3/8 700x18C 700
INSTALLATION AND OPERATION MANUAL - VDO CYTEC C 10 WL GB C 10 WL Preface Thank you for buying a VDO CYTEC bicycle computer. The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO CYTEC bicycle computer.
2. Mounting the speed transmitter GB Model VDO CYTEC C 10 WL works by radio transmission of speed impulses from the sender on the fork, to the receiver incorporated into the computer head mounted on the handlebar. Please be sure to get the sender aimed at the receiver (computer head) with as much precision as possible. The sender should be mounted on the same side of the fork as the holder is on the handlebar.
In case this distance is not achievable in the current positioning, slide the sender and the magnet on the fork or spoke accordingly. Watch out: Please remove the computerhead from the handlebar holder when you intend not to use your bike for a longer period of time. (battery power) GB C 10 WL 1-5m m m 1-5m 4. Twist-Click mounting of computer onto holder LOCK UNLOCK The Twist-Click mounting has been exclusively developed for the new line of VDO CYTEC computers.
GB C 10 WL 5. Installing battery into computer head To save battery power, your VDO CYTEC comes with the battery not yet fitted. Prior to initial use you have to install the battery first. OPEN CLOSE If you find the computer is not functioning properly after a battery change, push the AC-button (Auto Clear) on the rear side of the computer to reset.
6. Information features of your VDO CYTEC C 10 WL GB C 10 WL Your VDO CYTEC C 10 WL provides you with following information: KMH-MPH TRP RID STP AVS MAX TCNT CLK ODO WS 1+WS 2 current speed indicated in either KMH or MPH, featuring automatic conversion into MPH trip counter, counts your trip distance up to 999,99 km or miles.
GB 7.
These buttons / keys have several functions. All functions of the respective buttons / keys outlined in the following chart below. Your display Button / Key indicates following to be pushed information TRP-AVS-RID-STP- MODE 1 MAX TCNT-CLK- ODO MODE 1 TRP-RID-AVS MODE 1 TRP CLK ODO RID-AVS-STP-MAX TCNT TCNT-CLK- ODO TRP-RID-AVS-MAX MODE 1 MODE 1 MODE 1 MODE 1 MODE 1 MODE 2 MODE 2 TRP-RID-AVS-MAX TCNT STP STP MODE 2 MODE 2 MODE 2 MODE 2 Length of pushing the button / key brief (0.
GB 8. Scroll function C To provide any information at a glance, your VDO CYTEC C 10 WL features 10 a scroll function. Calling up the scroll function automatically displays WL information for a period of 1.5 sec. Scroll function may be called upon if any of the following information is on display: TRP-AVS-RID. Scroll function is activated by pressing the MODE 1 button for 1.5 sec. 9. Second trip counter TCNT Your VDO CYTEC features a second trip counter TCNT.
10. Manual stop-watch STP GB Your VDO CYTEC C 10 WL features a manual stop-watch. With information STP being displayed, you may operate your stop-watch with the MODE 2 -button. C 10 WL Watch out: Pressing the MODE 2 button for 5 sec. without STP data being displayed resets your TRP-AVS-RID-MAX data to zero. MODE 2 START/STOP MODE 2 MODE 2 MODE 2 Press MODE 2 5sec.
11. Comparison of current and average speed GB Your VDO CYTEC C 10 WL compares your current speed with your average speed. The outcome of this comparison can C be seen in your display by the use of symbols. No matter which information is currently displayed, this data keeps you 10 updated on the relation of your current speed and your average speed. WL Your current speed is faster than your average speed. Accuracy +/- 1 KMH/MPH You are currently riding as fast as your average speed.
. Selecting the wheelsize GB Your VDO CYTEC C 10 WL can work with two different wheelsizes (WS1 or WS2), i.e. one wheelsize for your road bike the other one for your mountain bike. When using the respective bike you can just switch to the proper wheelsize. C 10 WL Wheelsize is only selectable if any of the following information is displayed: AVS-RID-STP-MAX The currently active wheelsize is indicated in the display by WS 1 or WS 2.
GB C 10 WL 1x WS in mm / inch Programming (setting up) your wheelsize Step 1: Step 2: Step 3: Watch out: Step 4: Call TRP information in your display. Press MODE 1 button for 5 sec. "WS1" is displayed along with an alternating flashing symbol for KMH and MPH. By pressing the MODE 2 button you can choose whether you want MPH or KMH readout on your display. Your choice of either MPH or KMH applies for both wheelsizes WS 1 and WS 2.
GB MODE 1 5sec. C 10 WL MODE 1 5sec. to quit MODE 2 0,1sec. to change from KMH to MPH MODE 1 0,1sec. switch to next MODE 1 to start to switch to quit MODE 2 to increase to change from KMH to MPH MODE 1 0,1sec. switch to next MODE 1 0,1sec. switch to next MODE 2 0,1sec. to increase MODE 1 0,1sec. switch to next MODE 1 0,1sec.
GB C 10 WL 15. Setting the clock CLK Your VDO CYTEC C 10 WL features a clock with hour and minute display. 12 h or 24 h display selectable. To access the clock set-up mode proceed as follows: MODE 1 5sec. to start Step 1: call in the CLK information into your display Step 2: Press the MODE 1 button for 5 sec. The set-up mode for the clock starts. You will either see the figure "24" or "12" flashing reflecting the hour-mode programmed. To set up your clock use MODE 1 and MODE 2 buttons. (see set-up mode).
16. Programming (setting-up) your odometer ODO GB You can enter individual odometer values into your CYTEC C 10 WL at any time, i.e. transferring data from your old computer into your new VDO CYTEC C 10 WL or after a battery change. C 10 WL Watch out: after a battery change, your data for total ODO is reset to zero. TIP: If you want to re-enter your totals after a battery change, take down the value for ODO before removing the battery. Step 1: Call information for ODO into your display.
GB 17. Resetting information to zero C The following information may be reset to zero with your VDO CYTEC C 10 WL. 10 WL TRP-RID-AVS-MAX These information here is simultaneously reset to zero. TCNT This information is singly reset to zero. STP This information is singly reset to zero. Information must be reset to zero by pressing the MODE 2 button for 5 sec. Watch out: Take care that the exact information to be reset is on display.
Changing the sender battery GB Remove the battery door on the sender with either a coin or screwdriver. Insert the battery with the positive end (+) up. Close the battery compartment. C 10 WL Take care that the washer is precisely positioned on the battery compartment and is not jammed or wedged with the battery door. Watch out: old batteries require special disposal. Troubleshooting Hg This chart outlines possible malfunctions, their causes and solutions. malfunction irregular LCD readout (i.e.
GB 20. Warranty We warrant VDO CYTEC models (sensor, computer head and handlebar holder) to the original purchaser for five years C 10 from date of purchase against defects in material and workmanship. This does not cover the batteries and defects resulting WL from normal wear and tear, improper care, accidents, abuse or alteration. Please take care to retain your receipt of purchase. In case of legitimate complaints, you are entitled to receive a comparable replacement model.
