Specifications

ManualsBrandsVDO CYTEC ManualsBicycle AccessoriesC 10

RS/16 MAINFRAMERS/16 MAINFRAME

RS/16 MAINFRAME

RS SWITRS SWIT

RS SWIT

CH MODULESCH MODULES

CH MODULES

RSS/256 MAINFRAMERSS/256 MAINFRAME

RSS/256 MAINFRAME

RSS/16x8 SOLID STRSS/16x8 SOLID ST

RSS/16x8 SOLID ST

TE MODULESTE MODULES

TE MODULES

Fig. 2

RSS/16x8 TTL SWITRSS/16x8 TTL SWIT

RSS/16x8 TTL SWIT

CH MODULECH MODULE

CH MODULE

MAMA

TING CONNECTTING CONNECT

TING CONNECT

ORSORS

ORS

RS MULRS MUL

RS MUL

TIPLEXERTIPLEXER

TIPLEXER

These are passive, relay-based multiplexers

switching from 9 to 25 wire signals such as RS232,

RS422 or TTL in applications including Modems,

Printers or Token Ring.

Their Bandpass is DC to 20 MHz.

These are 19" rack mounted units 3.5" high and 15.6" deep

with power supplies, LED Displays and pre-wired motherboards

which accept the RS Switch Modules. This unit holds up to

sixteen RS Switch Modules and has sixteen switchpoint sta-

tus LEDs on the front panel. It can switch up to 25 wires from

sixteen input ports to one output port, or the reverse, as shown

in Figure 1.

RSS MARSS MA

RSS MA

TRIXTRIX

TRIX

These are built up from the RSS/16x8 Solid State

Modules, which in turn are plugged into pre-wired

RSS chassis. Each module is an individual 16x8

Matrix, and multiple modules can be intercon-

nected to form larger matrix configurations.

The RS/9, RS/15 and RS/25 Modules are built with Type

A relays, switching 9, 15 and 25 poles. Connector types

are subminiature D9, D15 or D25, and either -P pins or -S

sockets can be user specified.

RS/9 SWITCH MODULERS/9 SWITCH MODULE

RS/9 SWITCH MODULE

This is a solid state switch module and it is configured

as a 16 by 8 (16x8) matrix. Three separate versions are

built to handle either analog, TTL or RS422 signals. The

16 inputs are wired to a 34 pin header, the 8 outputs to a

20 pin header. The module is full fan out so any input

can be connected to one, several or all outputs.

RSS/16x8-A SWITRSS/16x8-A SWIT

RSS/16x8-A SWIT

CH MODULECH MODULE

CH MODULE

RSS/16x8-422 SWITRSS/16x8-422 SWIT

RSS/16x8-422 SWIT

CH MODULECH MODULE

CH MODULE

Switches sixteen individual, two wire RS422 signal inputs to

8, two-wire RS422 outputs as shown in Fig. 2 at up to 10

Mbps. Any input can be connected to one, several or even all

outputs.

This module switches +/-5 volt analog signals and has a typi-

cal ON resistance of 60 ohms. Bandpass is 50 MHz when

terminated into 1K ohms. It can be used as a 16x8 or 8x16

matrix.

This module switches TTL level signals and can be used as

either a 16x8 or 8x16 matrix. Any input can be connected to

any or all outputs.

CUSTOM SWITCH MODULESCUSTOM SWITCH MODULES

CUSTOM SWITCH MODULES

Switch Modules can be supplied that switch different types of

input and output signals on the same module. For example,

one module might have 16 two wire RS422 inputs switched

into eight single wire TTL outputs.

J20-R - Twenty pin ribbon cable type header connector

J20-C - Twenty pin crimp type header connector

J34-R -

Thirty-four pin ribbon cable type header connector

J34-C - Thirty-four pin crimp type header connector

RS/15 SWITCH MODULERS/15 SWITCH MODULE

RS/15 SWITCH MODULE

This module has a D15 connector with Type A relays switch-

ing all fifteen wires.

RS/25 SWITCH MODULERS/25 SWITCH MODULE

RS/25 SWITCH MODULE

This module utilizes a D25 connector and Type A relays switch-

ing all twenty-five wires.

AILABLE MAAILABLE MA

AILABLE MA

TING CONNECTTING CONNECT

TING CONNECT

ORSORS

ORS

D9-R - Nine pin ribbon cable connector

D9-C - Nine pin crimp type connector

D15-R - Fifteen pin ribbon cable connector

D15-C - Fifteen pin crimp type connector

D25-R - Twenty-five pin ribbon cable connector

D25-C - Twenty-five pin crimp type connector

Bi-directional Switching from 9 to 25 wires

Common

Device

Up to 16 Devices

16 X 8 MATRIX

RS-2

This is a 19" rack mounted chassis, 5.25" high and 15.6"

deep, pre-wired to accept the RSS Series of Switch Modules.

The unit has one slot that holds the required control module,

as well as slots for up to sixteen RSS/16x8 Switch Modules.

Multiple switch modules can be combined to form larger ma-

trices.

Figure 1

PLUG or SOCKET D TYPE CONNECTORSPLUG or SOCKET D TYPE CONNECTORS

PLUG or SOCKET D TYPE CONNECTORS

To specify Plug (male) D type connectors, add -P to the Switch

Module part number. Adding -S specifies Socket (female)

connectors. For example, the RS/15-S is built with a submin-

iature D15 Socket connector.

This module is built with a D9 connector and Type A relays

and switches nine wires.

The following mating connectors can be purchased for a small

additional charge.

EXPEXP

EXP

ANSION CHASSISANSION CHASSIS

ANSION CHASSIS

Expansion Chassis are built similar to the Mainframes except

they are not built with control modules or power supplies. They

are powered and controlled from a MESA Chassis as described

in the MESA Bulletin.

These are built similar to the Mainframes except they are not

built with control modules or power supplies. They are pow-

ered and controlled from a MESA Chassis as described in the

MESA Bulletin.

EXPEXP

EXP

ANSION CHASSISANSION CHASSIS

ANSION CHASSIS