Specifications

CONTACT 1-800-346-3117, [e-mail] OR WWW.CYTEC-ATE.COM
FOR TECHNICAL ASSISTANCE AND A COMPLETE CATALOG WITH PRICING!
NEW JX32/L2 SWITCH MODULE
This module has 32 two pole relays as shown in the
figure below with signal inputs wired to two 34 pin
header connectors. The two 16x1 muxes can be
jumpered together to form one 32x1 mux. The outputs
are available on a 10 pin header connector or can be
jumpered to the card edge connector which plugs into
the backplane. It is available with Type A relays only.
The relay specs are listed at the bottom of this page.
This module fits into all standard JX mainframes or
Expansion chassis. By using 16 of these modules, a
single JX mainframe can be configured as a 512x1 two
pole multiplexer or a 1016x1 single pole multiplexer.
HEADER CONNECTOR Pins 0-15 Top
HEADER
CONNECTOR
BACKPLANE
HEADER CONNECTOR Pins 16-31 Btm
NEW CPCI/64x1 TWO POLE MATRIX
NEW VME/16X16 RF MATRIX
CYTEC's VME/16x16 Video and RF Matrix module
uses a solid state switch fabric and is a nonblocking,
full fan-out 16x16 matrix with bandpass to 180 MHz.
This 6U VME or B sized VXI module may be used for
50 or 75 ohm signals and comes with SMB connec-
tors.
Typical applications include:
50 ohm RF communication signals.
75 ohm Video.
75 ohm DS3.
SPECIFICATIONS:
Price: $420.00
Availability: 1 week ARO
0
1
15210
2
15
16 Input
Buffers
16
output
Buffers
Bandpass:
75 ohms, 0.2 Vpp: >180 MHz, -3 dB
75 ohms, 2.0 Vpp: >100 MHz, -3 dB
50 ohms, 0.2 Vpp: >225 MHz, -3 dB
50 ohms, 4.0 Vpp: >165 MHz, -3 dB
50 ohm peak gain: +6 dB @ 150 MHz
Flatness: 1 dB to 40 MHz
Crosstalk: All hostile = <-55dB @ 10MHz
Isolation: Input to Output = <-60dB @ 10MHz
TYPE A RELAY SPECIFICATIONS:
Contact Rating: 30 Watts, 62.5 VA
Max. Switching Voltage: 110 VDC, 125 VAC
Switching Current: 1.0 A
Carrying Current: 2.0 A
Breakdown Voltage: 750 V
Operate Time: 3 ms
8x1
8x1
160 Pin High Density Connector
Jumpers
8x1
8x1
8x1 8x1 8x1
This Compact PCI / PXI switch module has 8 indepen-
dent 2 pole, 8x1 multiplexers. Each 8x1 segment may
be jumpered to another or used individually to provide
a large variety of configurations. All signals are brought
out to a high density 160 pin connector. The module
uses Type A relays only. The relay specs are listed on
the bottom of this page.
Price: $750.00
Availability: 2 weeks ARO
GENERAL SPECIFICATIONS:
Price: $3,500.00 each.
Available 2 weeks ARO.
Software support includes programming examples in C and driv-
ers for National Instruments LabView or LabWindows program-
ming platforms. Demonstration modules are available on request
VXI Revision: 1.4.
Module Size: VME 6U or VXI B size.
Logical Address: per DIP Switch setting.
Communication: Register Based.
Bus/Address Type: D16/A16/D08(O).
Write Cycle: less than 500 nsec.
Read Cycle: less than 500 nsec.
WARRANTY
CYTEC Corp. warrants that all products are free from defects
in Material or Workmanship for a period of 5 years and that all
switches are guaranteed for their rated operations.