Specifications

SERIES JX16 SWITCH MODULES
JX-2
Fig. 4
JX16/KP SWITCH MODULE
Fig. 5
JX16/KPC SWITCH MODULE
Fig. 6
JX16/L1 AND /L2 SWITCH MODULES
This Series of Switch Modules has 16 relays configured as
Multiplexers as shown in Figs. 1 & 2. These modules can
be used as separate muxes or bussed together on the back-
plane to form one multiplexer as large as 256x1.
Bandpass is 20 MHz (-3dB) and Isolation is less than 60dB
at 1 MHz when used in a 256x1 Mux.
JX16/L SWITCH MODULES
This Series of Switch Modules has 16 discrete relays with
all contacts brought out to connectors accessible from the
the chassis rear. Each relay has a Bandpass exceeding 20
MHz (-3dB) and Crosstalk less than 56dB at 1 MHz.
JX16/K SWITCH MODULES
JX 32/L2 SWITCH MODULE
Fig. 1
Fig. 2
Fig. 3
JX16/4(4x1)-1 and -2 SWITCH MODULES
This module has 16 single or two pole relays arranged as four
4x1 multiplexers as shown in Fig. 3. The muxes may be jum-
pered to the backplane to form up to a 256x1 mux or two 128x1
muxes. It is available with Type S, M or LT relays.
JX16/K1 SWITCH MODULE
This module has 16 single pole relays as shown in Fig. 4 with
both sides of all relays brought out to a 34 pin Header connec-
tor. The module is available with Type S or Type M relays.
JX16/KC SWITCH MODULE
The JX16 Switch Modules plug into the JX/256 Mainframe and Expansion Chassis and typically are built
with 16 relays and their associated solid state controls, including Status feedback.
The Modules are available with high reliability reed relays that have a guaranteed life of 100 million
operations and with the option of either Type S - Standard Dry Reed, Type M - Mercury Wetted Reed or
Type LT - Low Thermal Reed. They are also available with Armature type Power Relays for switching up
to 2000 VA power or 8 amps current.
There are three basic types of Modules: JX16/L for Multiplexing configurations, JX16/K for discrete
relays, and JX16/AB for x2 Matrix configurations.
This module has 16 single or two pole relays as shown in Fig. 1
with signal inputs wired to a 34 pin header connector. The two
8x1 muxes may be jumpered together to form a 16x1. The
outputs are available on a 10 pin header connector or can be
jumpered to the card edge connector which plugs into the
backplane. It is available with Type S, M or LT relays.
This module has 32 two pole relays as shown in Fig. 2 with
signal inputs wired to two 34 pin header connectors. The two
16x1 muxes can be jumpered together to form one 32x1 mux.
The outputs are available on a 10 pin header connector or can
be jumpered to the card edge connector which plugs into the
backplane. It is available with Type A relays only.
This module has 16 single pole, Type P power relays as shown
in Fig. 4 with both sides brought out to a 37 pin D type connec-
tor.
HEADER CONNECTOR
HEADER
CONNECTOR
BACKPLANE
HEADER
CONNECTOR
HEADER CONNECTOR
BACKPLANE
01234567
8 9 10 11 12 13 14 15
01234567
8 9 10 11 12 13 14 15
01234567
This module has 16 single pole, double throw relays as shown
in Fig. 5 with all contacts brought out to a 50 pin Header con-
nector. The module is available with either Type CS or Type
CM relays.
JX16/KCA SWITCH MODULE
This module has 16 single pole, double throw relays as shown
in Fig. 5 with all contacts brought out to a 50 pin Header con-
nector. The module is available with Type A relays only.
This module has 8 single pole, double throw discrete Form C
Type P power relays shown in Fig. 6 with all contacts brought
out to screw terminal connectors.
HEADER CONNECTOR Pins 0-15 Top
HEADER
CONNECTOR
BACKPLANE
HEADER CONNECTOR Pins 16-31 Btm