Specifications

ManualsBrandsVDO CYTEC ManualsBicycle AccessoriesC 10

2555 Baird Road, Penfield, New York 14526 (585) 381-4740 FAX (585) 381-0475

BULLETIN

DX-1

CONTACT 1-800-346-3117 OR WWW.CYTEC-ATE.COM

FOR TECHNICAL ASSISTANCE

DX SERIESDX SERIES

DX SERIES

SOLID STSOLID ST

SOLID ST

TE DIGITTE DIGIT

TE DIGIT

AL SWITAL SWIT

AL SWIT

CHING SYSTEMSCHING SYSTEMS

CHING SYSTEMS

CYTEC's DX Series Switching Systems are based on solid state switch fabric.

The Standard DX system is designed to switch TTL, CMOS, LVTTL, IRIG, RS232

and RS422. Input and output buffers are used to convert to RS422 and/or RS232

signal levels. The DX is capable of switching data rates to 80 Mbps NRZ. The

DX Matrix is a nonblocking, full fan-out configurations from 64x64 up to 256x256.

Control options include RS232/ IEEE488, LAN or LCD Keypad Manual Control.

The DX/256X256 Series are 19" rack mounting units and

are built as either Mainframe or Expansion Chassis. The

Solid State Digital Matrix is modular, capable of being

expanded from a 64x64 to a 256x256 by adding the de-

sired number of input and output modules. The con-

figurations occur in 64 channel increments so typical

configurations will be 64x448, 128x384, 256x256, etc.

Other possible configurations such as dual 12x12 clock

and data matrices or multi chassis clock and data sys-

tems are also available. The DX Series Matrix is com-

pletely nonblocking and full fan-out.

DX/256X256 CHASSISDX/256X256 CHASSIS

DX/256X256 CHASSIS

IFIF

-6 LAN INTERF-6 LAN INTERF

-6 LAN INTERF

CECE

DX/256x256 Mainframe Rear View

CUSTCUST

CUST

OM CHASSISOM CHASSIS

OM CHASSIS

Custom configurations are available upon request. Most cus-

tom systems wire out the rear panel Input/Output connec-

tions to a required connector type that is different from the

standard 64 pin male header or 78 pin female D Connectors.

This wiring is priced on the basis of labor and materials.

MANUAL CONTROLMANUAL CONTROL

MANUAL CONTROL

This Virtual Manual Control Software allows a remote operator

using a PC to view matrix Status and control switches using a

full Graphical User Interface.

MCMC

-2 WITH LCD DISPLA-2 WITH LCD DISPLA

-2 WITH LCD DISPLA

VMCSVMCS

VMCS

CONTROL MODULESCONTROL MODULES

CONTROL MODULES

DX/256X256 MAINFRAMEDX/256X256 MAINFRAME

DX/256X256 MAINFRAME

The Standard Mainframes are built with power supplies, user

specified Control Module and optionally Keypad LCD Display

Manual Control. The system is completely modular by add-

ing the desired number of DX/64 Input and Output Switch

Modules defined on page 2 of the bulletin.

The expansion chassis is identical to the mainframe in size

and function. The expansion chassis, however, is built with-

out a dedicated control module, manual control or power sup-

plies. Instead, it is designed to be both powered and con-

trolled by one of CYTEC's MESA Control Chassis detailed in

the MESA Bulletin. Ribbon Expansion Cables connect the

expansion chassis to the MESA.

DX/256x256-E EXPANSION CHASSISDX/256x256-E EXPANSION CHASSIS

DX/256x256-E EXPANSION CHASSIS

IFIF

-5 IEEE488/RS232 CONTROL MODULE-5 IEEE488/RS232 CONTROL MODULE

-5 IEEE488/RS232 CONTROL MODULE

This module provides remote control via both RS232 Serial

and IEEE488 Talk/Listen interfaces as detailed in Applica-

tions Bulletin AP-5.

This optional module allows control over a 10BaseT Ethernet

Local Area Network via TCP/IP protocols as described in Ap-

plications Bulletin AP-5.

This local control supplies a front panel Keypad and LCD Dis-

play that lets the operator control any switch and verify switch

status.