Specifications

ManualsBrandsVDO CYTEC ManualsBicycle AccessoriesC 10

RAM OPTIONRAM OPTION

RAM OPTION

PX-4

CONTROL MODULESCONTROL MODULES

CONTROL MODULES

FOR TECHNICAL ASSISTFOR TECHNICAL ASSIST

FOR TECHNICAL ASSIST

ANCE CONTANCE CONT

ANCE CONT

CT 1-800-346-3117 orCT 1-800-346-3117 or

CT 1-800-346-3117 or

WWWWWW

WWW

.CYTEC.CYTEC

.CYTEC

TETE

.COM..COM.

.COM.

SWITSWIT

SWIT

CH SPECIFICACH SPECIFICA

CH SPECIFICA

TIONSTIONS

TIONS

The Modules and Chassis are available with the following

options selected by the suffix at the end of the Model Num-

ber:

CONNECTCONNECT

CONNECT

OR OPTIONSOR OPTIONS

OR OPTIONS

Power - 100-130 Volts AC or 200-240 Volts AC,

50 to 60 Hz, 100 W.

Environment - Operating Temperature 0

to 50

Storage Temperature -25

to 65

GENERAL SPECIFICAGENERAL SPECIFICA

GENERAL SPECIFICA

TIONSTIONS

TIONS

• Bandpass DC to 10 MHz

• Isolation -40dB at 10 MHz

• Crosstalk -40dB at 10 MHz

64x8 MATRICES

• Bandpass DC to 20 MHz

• Isolation -40dB at 10 MHz

• Crosstalk -30dB at 10 MHz

32x16 MATRICES

The Matrices are designed for maximum bandpass and iso-

lation between channels.

All test results are on a full chassis of 16 modules with 50

ohm source and 50 ohm termination.

MAMA

TRIX SPECIFICATRIX SPECIFICA

TRIX SPECIFICA

TIONSTIONS

TIONS

Three types of switches are available, the Type S, Type M

and Type LT.

Type S Standard is a dry reed switch for most medium range

applications.

Type M Mercury is a mercury wetted switch for high power

or low contact resistance applications.

Type LT Low Thermal is a dry reed switch for low level ap-

plications with less than 1 microvolt offset.

All switches are guaranteed for 100 million operations when

used within the following specifications:

SOFTWSOFTW

SOFTW

AREARE

ARE

This option is available with the above Control Modules and

with the MESA Control Unit.

Switch selections can be stored in a battery back up RAM so

that the switches can be latched to a preset configuration up

to 1000 switch selections.

After power loss, the switch matrix will reset to the last se-

lected switch configuration.

This Manual Control has a Keypad and LCD Display on the

front panel so that the operator can select any relay and Latch

the Relay or check the Status of the Relay on the Display.

MCMC

-2 MANU-2 MANU

-2 MANU

AL CONTROLAL CONTROL

AL CONTROL

This Module combines all the features of the RS232 Serial

and IEEE488 GPIB Bus Modules detailed in the Applications

Bulletin AP-5.

IFIF

-5 IEEE488/RS232 COMBINED MODULE-5 IEEE488/RS232 COMBINED MODULE

-5 IEEE488/RS232 COMBINED MODULE

Plug in Modules control the PX/512 Mainframes from the

IEEE488 Bus or the RS232 Serial Port.

The Controls can Select and Latch or Unlatch any Switch

in the Matrix. The controls can also request the Status

of any Switch or can Request the Status of the complete

Matrix.

The cycle time to Select and Latch a relay and obtain

status is 30 msec.

IFIF

-6 LAN INTERF-6 LAN INTERF

-6 LAN INTERF

CECE

Drivers and/or sample programs are available for the most

commonly available application programming languages.

CYTEC SWITCYTEC SWIT

CYTEC SWIT

CH MANACH MANA

CH MANA

GER SOFTWGER SOFTW

GER SOFTW

AREARE

ARE

This module interfaces between the Local Area Network and

the RS232 Control Modules using TCP/IP commands as de-

scribed in the Applications Bulletin AP-5.

Type S Type M Type LT

Contact Rating 10VA 50VA 10VA

Maximum Switch Voltage 200V 500V 100V

Maximum Switch Current 0.5A 2A 0.2A

Breakdown Voltage 400V 1000V 200V

Operate Time, less than 1ms 2ms 1ms

-N

-H

-S

-W

Indicates the BNC receptacles with isolated shield for

two pole switching and ground shield for single pole

switching.

Indicates header connectors, with 16 pin headers for the

single pole modules and 20 pin headers with two wire

plus shield for two pole switching.

Indicates terminal with screw terminal mates which have

two terminals for the single pole modules and three ter-

minals for two pole modules.

Indicates special wiring to customer specification.

WARRANTYWARRANTY

WARRANTY

CYTEC Corp. warrants that all products are free from de-

fects in Workmanship and Materials for a period of five years

and that all switches are guaranteed for their Rated Opera-

tions.

The Cytec Switch Manager provides a GUI inter-

face for controlling matrices and multiplexers via

remote computer. The software includes an intui-

tive graphical interface, security implementation,

built in test functionality, multiple device control, switchpoint

memory, as well as many other useful features. You can down-

load the Switch Manager from our website.

Available for Windows, Linux, Mac OS, or any other

Java enabled platform