VIP 1000 User Guide
Copyright This user guide is the intellectual property of VCS and is protected by copyright. All rights reserved. No part of this document may be reproduced or transmitted for any purpose, by whatever means, electronic or mechanical, without the express written permission of VCS. Release: July 2005 (Firmware Version 2.1) © 2005, VCS Video Communication Systems AG Note This user guide has been compiled with great care and the information it contains has been thoroughly verified.
Contents Contents 0 Chapter 1 Preface About this user guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EU guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Camera name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display stamping . . . . . . . . . . .
Contents Chapter 8 Sender Operation Operation with Microsoft Internet Explorer . . . . . . . . . . . . . . . . . The Livepage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Saving snapshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recording video sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 92 97 98 Chapter 9 Receiver Operation Operation with Microsoft Internet Explorer . . . . . . . . . . . . . . . . .
Contents 6 VIP 1000
Preface 1 About this user guide This user guide is intended for persons responsible for the installation and operation of the VIP 1000 network video server. International, national and any regional regulations regarding electrical systems must be adhered to at all times. Adequate knowledge of network technology is a precondition. The user manual describes the installation and operation of the unit.
Preface Chapter 1 Intended use The VIP 1000 network video server transmits video, audio and control signals over data networks (such as Ethernet LANs and the Internet). It is designed for use in CCTV systems. By incorporating external alarm devices, various functions can be triggered automatically. Other applications are not authorized.
Safety Information 2 Electrical shock hazard ] Never attempt to connect the unit to any power network other than the type for which it was intended. ] Use only the power supply provided. ] Never open the casing! ] If a fault occurs, disconnect the power supply unit from the mains supply and from all other devices. ] Install the unit and power supply only in dry, weather-protected areas.
Safety Information Chapter 2 Installation and operation ] Relevant electrical codes and guidelines must be complied with at all times during installation. ] Adequate knowledge of network technology is necessary for the installation. ] Before installing or operating the unit, make sure you have read and understood the documentation for the other equipment connected to the system, such as cameras. There you will find important safety instructions and information about authorised use.
Product Description 3 Supplied components ] Network video server VIP 1000 including plug-in mains adapter ] Configuration cable ] The quick start guide “First Steps” in English and German ] Product CD with the following content: – The quick start guide “First Steps” in English and German – User guide in English and German – System Requirements – MPEG-ActiveX control – MPEG-Viewer – DirectX control – Microsoft Internet Explorer – Microsoft Virtual Machine – Adobe Acrobat Reader System requirements for set
Product Description Chapter 3 Note Read the indications given in the document System Requirements on the CD provided. Make sure the graphic card is set to 16 or 32 bit color depth and Microsoft's Virtual Machine is installed and active on your computer. Operational requirements ] Computer with Microsoft Windows 98/2000/XP operating system and network access and – Microsoft Internet Explorer (version 6.0 or later) or – decoder software, such as VIDOS from VCS or ] Hardware receiver from VCS (e.g.
Chapter 3 Product Description Overview of functions Network video server The VIP 1000 is an ultra-compact network video server. Its primary function is to encode and decode video, audio and control data for transmission over an IP network. The VIP 1000 is particularly well suited to adapting analog cameras for IP communication and for remote access to digital video recorders and multiplexers. About the size and shape of a cigarette packet, it can be integrated into small enclosures without difficulty.
Product Description Chapter 3 Multicast In suitably configured networks, the multicast function enables simultaneous, real time video transmission to multiple receivers. The prerequisite for this is that the UDP and IGMP V2 protocols be implemented on the network. Remote control The VIP can remotely control external devices, such as pan and tilt heads or motorized zoom lenses, by transmitting control data via its bidirectional serial interface. This interface can also be used to transmit transparent data.
Chapter 3 Product Description Summary The main functions of the VIP 1000 are: ] Video, audio and data transmission over IP data networks ] Simultaneous dual streaming with two independently defined profiles ] Multicast function for simultaneous picture transmission to multiple receivers ] Analog BNC composite video input FBAS (PAL/NTSC) (sender) ] Analog BNC composite video output FBAS (PAL/NTSC) (receiver) ] A bidirectional audio input/output (mono) ] Video and audio encoding using the MPEG-4/G.
Product Description Chapter 3 VIP 1000 sender connections 1 2 RS232/485 Video In Li LoIN1 R + USB GNDIN2 R 3 4 5 ñ Ethernet 6 7 8 9 1 BNC jack Video In for connecting a video source 2 RJ45 jack for RS232/485 for transmitting control data and configuration with terminal software 3 USB interface for future expansion of the recording function 4 Reset button for restoring the default settings 5 Terminal block (audio, alarms, relay and power supply) 6 Operating status LED yellow, lights up when
Chapter 3 Product Description VIP 1000 receiver connections 1 2 Video Out RS232/485 Li LoIN1 R + USB GNDIN2 R 3 4 5 ñ Ethernet 6 7 8 9 1 BNC jack Video Out for connecting an analog video monitor 2 RS232/485 serial interface 9-pin Sub-D socket (male) for transmitting control data and configuration with terminal software 3 USB interface for future expansion of the recording function 4 Reset button for restoring the default settings 5 Terminal block (audio, alarms, relay and power supply) 6 Op
Product Description Chapter 3 18 VIP 1000
Installation 4 Installing the unit With its ultra-compact dimensions, the VIP is particularly well suited for installation in cabinets. Warning! The unit is intended for use indoors or in a protective enclosure. Select a suitable location for installation where the equipment is not subject to extreme temperatures or humidity. The ambient temperature must lie between 0 and +50 °C. The relative humidity should not exceed 80%. The unit generates heat during operation.
Installation Chapter 4 Connections Camera/monitor Depending on the device used, you can connect a video source (sender) or a monitor (receiver). All cameras and video sources that generate a standard PAL or NTSC signal and all monitors compatible with PAL or NTSC standards can be used for this purpose. – Connect the camera or another video source using a video cable (75 Ohms, BNC plug) to the Video In BNC jack of the sender.
Chapter 4 Installation Network You can connect the VIP to a 10/100 Base-T network. Use a standard UTP Category 5 cable with RJ45 connectors for this. – Connect the unit to the network using the Ethernet jack. Alarm inputs The VIP has two alarm inputs on the orange terminal block. The alarm inputs are used to transfer signals from external alarm devices, such as door contacts or sensors.
Installation Chapter 4 The bidirectional audio signals are transmitted simultaneously with the video signals. This can be used for example to operate a loudspeaker or door intercom at the target location. – Connect a line level audio source to the appropriate terminals on the orange terminal block of the sender and check that the connection is secure. – Connect a loudspeaker to the appropriate terminals on the orange terminal block of the receiver and check that the connection is secure.
Chapter 4 Installation Setup using terminal software Data terminal You can connect a data terminal to the VIP for setup and local control. The data terminal consists of a computer with terminal software. Use the configuration cable included in the package supplied to make the connection. For example, HyperTerminal, a communications utility included with Microsoft Windows, can be used as the terminal program.
Installation Chapter 4 ] Enter only one command at a time. ] After entering a value (such as an IP address), re-check the entry before pressing the Enter key to send the data to the VIP. Assigning an IP address To operate the VIP on your network, you must assign it an IP address that is recognized by the network. The following default address has been pre-set at the factory: Sender: 192.168.0.1 Receiver: 192.168.0.2 – Start up a terminal program such as HyperTerminal. – Enter service as user name.
Chapter 4 Installation Note The new IP address, subnet mask and gateway adress become effective only following a restart. Restart Disconnect the VIP from the power socket, wait a few seconds and reconnect the unit. Additional parameters Using the terminal program, you can check other basic parameters and modify them where necessary. Use the on-screen commands displayed in the various submenus for this purpose.
VIP 1000
Configuration using a Web Browser 5 Establishing the connection The integrated HTTP server allows the unit to be configured over the network using a Web browser. This option offers considerably more possibilities and is more convenient than configuration using terminal software. It also allows live video images to be displayed. Note Make sure the graphic card is set to 16 or 32 bit color depth and the Microsoft Virtual Machine is installed and active on your computer.
Configuration using a Web Browser Chapter 5 Establishing the connection The VIP must be assigned a valid IP address for your network, before it can be operated in your network environment. The following default address has been pre-set at the factory: Sender: 192.168.0.1 Receiver: 192.168.0.2 – Start the Web browser. – Enter the IP address of the VIP as the URL. The VIP home page will be shown in the browser. If the unit is a sender, the home page will be the Livepage (which shows the live video image).
Chapter 5 Configuration using a Web Browser The Decoder connection page will be displayed as the home page for a receiver. It shows a snapshot from the video source for the sender currently connected, and the unit searches the network automatically for available senders. Note If the connection is not established, the maximum number of possible connections may already have been reached. The maximum number of connections depends on the unit and network configuration.
Configuration using a Web Browser Chapter 5 Choosing the configuration mode There are two options to configure the VIP or to check the current setup: ] the Wizard and ] Expert Mode. All settings are stored in the VIP memory, and they are preserved even if the power is interrupted. Use of the Wizard is recommended for initial setup. It takes you step by step through the necessary settings. It prevents critical settings for correct operation being overlooked.
Chapter 5 Configuration using a Web Browser Configuration with the Wizard The Wizard is used for step-by-step configuration of the VIP. It will lead you through a series of screens where you can input the necessary settings. The settings only become effective after the last screen of the Wizard has been completed. When working with the Wizard, you can switch to another window at any time. The last screen of the Installation Wizard offers the option of launching the Application Wizard.
Configuration using a Web Browser Chapter 5 General procedure The screens for the Installation Wizard will be shown in sequence, allowing you to work quickly and easily. The upper part of the window always contains information about the settings options. The current settings are shown in the lower part of the window. You can change settings by entering the desired value in a text field or choosing it from a list. The navigation buttons for the Installation Wizard are at the bottom of the window.
Chapter 5 Configuration using a Web Browser Configuration in Expert Mode Expert Mode allows all parameters of the VIP to be configured. You can view the current settings by opening one of the configuration pages. The settings can be changed by entering new values or by selecting a predefined value in a list field. The basic use of the configuration pages is described below.
Configuration using a Web Browser Chapter 5 Making changes Each configuration page shows the current settings. You can change the settings by entering new values or by selecting from predefined lists. – Click Set after each change to save it. Warning! Save each change with the associated Set button. When Set is clicked, only the changes in the relevant field are saved. Changes in any other fields are ignored.
Configuring the Sender 6 Basics The VIP offers various configuration options. Configuration in Expert Mode with a Web browser is described below. Basic information about configuration with a Web browser and other configuration options are described in Chapter 5 of this user guide. Unit identification The unit can be assigned a name and an ID to facilitate identification. Both make the task of managing several units in larger video surveillance systems with VIDOS from VCS or other tools much simpler.
Configuring the Sender Chapter 6 Password A VIP unit is generally protected by password to prevent unauthorized access. You can limit the scale of access by choosing between different authorization levels (User name:). Note Correct password protection is only granted when all higher levels of authorization are also protected by password. If a live password is assigned, for example, also a service and a user password must be assigned.
Chapter 6 Configuring the Sender Confirm password: Re-enter the new password to prevent typing mistakes. Note The new password becomes effective only after you have clicked Set. Therefore always click Set immediately after having entered and confirmed the password even if afterwards you want to assign a password to another user name, too. Language Website language: Select the language for the website from the dropdown field.
Configuring the Sender Chapter 6 Unit date: Enter the current date here. Since the unit time is controlled by the internal clock, it is not necessary to enter the day of week. This is added automatically. Unit time: Enter the current time here or click the Synchr. PC button to copy the system time of your computer to the VIP. Time server Using a Time Server Protocol the VIP can receive a time signal from a time server and use it to set its internal clock.
Chapter 6 Configuring the Sender Camera name The camera name simplifies identification of the remote camera location, for example in the event of an alarm call. It will be shown in the video image if this facility has been configured (see page 39). Moreover, the camera name is used by VIDOS, VCS software for managing video surveillance systems, and makes it easier to identify the camera. Camera: Enter a unique, unambiguous name for the camera in this field.
Configuring the Sender Chapter 6 Time stamping: This field sets the position of the time and date overlay. It can be shown at the Top or the Bottom or you can define a position yourself via the Hyperterminal and activate it choosing the option Custom. Or it can be set to Off if no overlay for this information is to be shown. Alarm mode stamping: Choose On if a text message should be overlaid in the event of an alarm. Displayed alarm message: Enter the message to be displayed for an alarm.
Chapter 6 Configuring the Sender Picture settings You can set up the video picture to meet your own particular requirements. To enable you to control the current video picture it is shown in a small window beside the sliders. The changes are effective immediately. – If necessary click the Default button to return the configuration back to the standard settings. Contrast (0...255): You can use this function to adjust the contrast of the video picture to suit the working environment. Saturation (0...
Configuring the Sender Chapter 6 MPEG-2 encoder The data transmission parameters can be configured to suit the local operating environment (network architecture, bandwidth, data structures, etc.). Eight preconfigured profiles are provided in MPEG-2 mode, each reflecting different priorities and environments. Individual settings in a profile and its name can be changed. Warning! The profiles are rather complex. They include a number of parameters that interact with one another.
Chapter 6 Configuring the Sender ] 2MBPS high quality 2 MBit/s transmission rate with high image quality ] 3.5MBPS high quality 3.5 MBit/s transmission rate with high image quality ] 5MBPS high quality 5 MBit/s transmission rate with high image quality ] 2MBPS video, 256KBPS audio 2 MBit/s transmission rate with additional audio transmission ] 4MBPS video, 256KBPS audio 3.
Configuring the Sender Chapter 6 ] I I-frames only ] IP an I-frame followed by several P-frames ] IPB an I-frame followed by several substructure sequences, each consisting of a P-frame and a B-frame ] IPBB an I-Frame followed by several substructure sequences, each consisting of a P-frame and two B-frames GOP length: Enter the image interval between I-frames here. The value will depend on the GOP structure selected. It must always be a multiple of the P- frames and Bframes in the GOP structure.
Chapter 6 ] CIF Configuring the Sender 352 × 288/240 pixels ] D1/4CIF 704 × 576/480 pixels Reset of profile: Click the Default button to reset the profile to its factory presets. MPEG-4 encoder You can configure the data transmission parameters for the MPEG-4 encoder to suit the operating environment (for example the network structure, bandwidth, data structures etc.).
Configuring the Sender Chapter 6 ] Profile 1: High quality (CIF) high quality for connections with high bandwidth, resolution 352 × 288/240 pixels ] Profile 2: High resolution (2CIF) for connections with high bandwidth, resolution 704 × 288/240 pixels ] Profile 3: Low resolution (QCIF) for connections with low bandwidth, resolution 176 × 144/120 pixels ] Profile 4: DSL for DSL connections with 500 kBit/s, resolution 352 × 288/240 pixels ] Profile 5: ISDN (2B) for ISDN connections via two B channels, resol
Chapter 6 Configuring the Sender Profile configuration Individual settings in a profile and its name can be changed. You can switch between the profiles by clicking the associated tabs. Warning! The profiles are rather complex. They include a number of parameters that interact with one another. Therefore it is generally best to use the profiles as provided. The profiles should only be changed after you have familiarized yourself with all the configuration options.
Configuring the Sender Chapter 6 Encoding interval: This setting determines the frame encoding interval. With the value 4 e.g. only every fourth image is encoded, the following three images are skipped, which is an advantage especially with low bandwidth. Video resolution: Select the desired resolution for the MPEG-4 video image.
Chapter 6 Configuring the Sender Warning! G.711 audio data is only saved with central recording, using VIDOS-NVR for example. Enable audio: To transmit a separate G.711 audio stream choose On. Video input The 75 Ohm termination of the VIP can be set here. If the video signal is to be looped through, the termination must be set off. The default setting for the video input termination is On. 75 Ohm termination: To loop the video signal through choose Off.
Configuring the Sender Chapter 6 JPEG posting You can store video images in JPEG format at certain intervals on an FTP server. These images can be called up again later, thus enabling for example alarm events to be reconstructed. JPEG format: Here you can choose the format of the JPEG pictures: ] S 176 × 144/120 pixel ] M 352 × 288/240 pixel ] XL 704 × 576/480 pixel File name: You can set what file names are to be generated for the transmitted snapshots.
Chapter 6 Configuring the Sender JPEG posting interval: Enter the time interval here at which the single images are to be sent to an FTP server. Enter zero, if no single images are to be sent. FTP server IP address: Enter here the IP address of the FTP server on which the JPEG-images are to be stored. FTP login name: Enter your login name for the FTP server here. FTP password: Enter the password for the access to the FTP server here.
Configuring the Sender Chapter 6 Video loss alarm: Select On if the unit is to activate an alarm whenever the video signal is interrupted. Contrast alarm: The VIP can trigger an alarm if the camera image shows too little contrast, possibly indicating that the lens has been sprayed with paint or covered in some way. Select On to enable this function. Motion alarm: Select On if the unit is to respond to a motion alarm. Motion detection is configured on a separate page (see page 54). Alarm input 1 ...
Chapter 6 Configuring the Sender Alarm connections You can select a number of options for the response of the VIP to an alarm. In case of an alarm, the VIP can establish a connection to a predefined IP address (VCS hardware receiver or PC with receiver software) automatically. You can enter up to ten IP addresses which will be selected in sequence by the unit until a connection is established. Note Sender and receiver must share the same subnet for connection set-up (see page 62).
Configuring the Sender Chapter 6 Number of destination address: Here you assign the numbering for the IP addresses to be contacted in the event of an alarm. The unit contacts the remote locations one after the other in the numbered sequence until a connection has been established. Destination IP address: For each number, enter the corresponding IP address of the desired remote unit. Destination password: Enter the password, if the remote unit is protected by a password.
Chapter 6 Configuring the Sender The sensitivity of the video sensor can be adjusted, so an alarm is generated only if specified values are exceeded. Note The video sensor monitors Stream 1. For exact motion detection it is recommended to choose CIF as video resolution for Stream 1 (see page 45). In order for the sensor to function, the following conditions must be met: ] The motion detector must be enabled. ] At least one sensor field must be activated.
Configuring the Sender Chapter 6 be activated or deactivated individually. If it is necessary to exclude particular regions of the camera's field of view from monitoring due to continuous movement (by a tree in the wind, etc.), the relevant fields can be deactivated. – Click Select area to configure the sensor fields. A new window will open. – If necessary, click Clear all first to clear the current selection (fields marked red). – Left-click the fields to be activated. Activated fields are marked red.
Chapter 6 Configuring the Sender Motion indicator To prevent false alarms, a threshold can be applied to the motion signal. This allows effects such as the background noise from the camera itself to be filtered out. The blue line in the illustration represents the alarm threshold. Any value above this level will trigger an alarm. The parts of the motion signal line which will cause an alarm are shown in red. The alarm threshold can be set higher or lower to suit your needs.
Configuring the Sender Chapter 6 Relay You can configure the switching behavior of the relay output. Relay action can be specified either as open switch (normally closed contact) or closed switch (normally open contact). It is also possible to specify whether the output signal should be bistable or monostable. With bistable operation, the relay remains in the activated state. With monostable operation, the delay time can be selected after which the relay reverts to its idle state.
Chapter 6 Configuring the Sender Relay follows: Select a particular event to trigger the relay.
Configuring the Sender Chapter 6 COM1 The RS232/485 serial interface port can be configured to meet your requirements. Serial port function: Select a controllable device from the list. If you want to use the serial interface to transmit transparent data, select Transparent. To operate the VIP with a terminal, choose Terminal. Note After selecting an option, the remaining parameters in the window are set automatically and should not be altered.
Chapter 6 Configuring the Sender Data bits: The number of data bits per character cannot be changed. Stop bits: Select the number of stop bits per character. Parity check: Select the type of parity check. Interface mode: Select the desired protocol for the serial interface. Half-duplex mode: Choose the setting appropriate for your application. Network The settings on this page are used to integrate the unit into an existing network.
Configuring the Sender Chapter 6 Warning! Changes to the IP address, subnet mask or gateway address are sent to the unit when the Set button is clicked. However, they only take effect after the unit is restarted! – Click Set after entering a new IP address. – Enter the old IP address in the address field of the Web browser and append /reset to it (e.g. 192.168.0.1/reset). The VIP will be restarted after which it can only be accessed at the new IP address.
Chapter 6 Configuring the Sender Ethernet link type: If the VIP is connected to the network via a switch, both devices must be set for the same type of network connection. If necessary, ask your network administrator about the switch setting. Choose Auto for an autosensing network connection. If necessary you can set the value to 10 or 100 MBit/s and full or half-duplex mode (FD or HD).
Configuring the Sender Chapter 6 Multicasting In addition to a 1:1 connection between an encoder and a single receiver (unicast), the VIP can enable multiple receivers to receive the video signal from an encoder simultaneously. This is achieved either by duplicating the data stream in the unit with subsequent distribution to multiple receivers (multi-unicast) or by distribution of a single data stream over the network to a number of receivers in a defined group (multicast).
Chapter 6 Configuring the Sender Multicast streaming: Select one of the options MPEG-2, MPEG-4 or MPEG-2/MPEG-4 to enable multicast streaming. Off disables multicast streaming. Multicast address MPEG-2 ... Multicast address MPEG-4 Stream 2: Enter a valid multicast address for each data stream, so that it will be accessible in multicast mode (duplication of the data streams in the network) When the multicast address is set to 0.0.0.
Configuring the Sender Chapter 6 Multicast packet TTL: This value determines the "life span" of multicast packets on the network. If multicast is operated via a router, the value must be greater than 1 to ensure that the packets are passed on. Version information The hardware and firmware version numbers are for information only and cannot be altered. Keep a record of these numbers in case technical assistance is required. Hardware version: The hardware version number of the VIP is displayed.
Chapter 6 Configuring the Sender Livepage configuration In this dialog, the appearance of the Livepage can be set up to suit your requirements. Options are provided here to display various information and operating elements in addition to the video image. Moreover, individual background graphics can be used for the main window and for the upper area of the window (banner). Note Either GIF or JPEG images can be used. The file paths must correspond to the access mode (local paths such as C:\Images\Logo.
Configuring the Sender Chapter 6 – Check the display of the desired information on the Livepage. Background URL: Enter the path to a suitable background graphic in this field. The image can be stored on a local computer, a local network or at an Internet address. – Click Search if necessary to find a suitable image on the local network. Logo URL: Enter here the path for a suitable image for the upper part of the window (banner).
Chapter 6 Configuring the Sender Show system log: The system log will be displayed with date and time in a field under the video image and provide information about connections, etc. Panorama (Sony camera only): Selecting this option enables the display of a panoramic image. The panoramic image is shown in the upper part of the browser window. It consists of five single images that can be updated any time (see page 96).
Configuring the Sender Chapter 6 Path for JPEG and MPEG files: Enter the full path for saving snapshots and video sequences to be saved from the Livepage. – If necessary, click Search to find a suitable folder. Firmware and configuration upload Firmware update: The VIP is designed in such a way that its functions and parameters can be updated with firmware. To accomplish this, the current firmware is loaded on the unit via the selected network. It will be installed automatically.
Chapter 6 Configuring the Sender – Enter the full path for the update file in the field or click Durchsuchen... to locate and select the file. – Click Upload to begin transmission to the unit. Transmission progress can be monitored from the progress bar. The new firmware will be decompressed and used to reprogram the flash EPROM. The time necessary is indicated by the message going to reset Reconnecting in ... seconds. After the upload is completed successfully, the unit will restart automatically.
Configuring the Sender Chapter 6 Function test The VIP offers a number of configuration options. Therefore you should check that it works properly after installation and configuration. This is the only way to ensure that the VIP will function as intended in an alarm situation.
Configuring the Receiver 7 Basics The VIP offers various configuration options. Configuration in Expert Mode with a Web browser is described below. Basic information about configuration with a Web browser and other configuration options are described in Chapter 5 of this user guide. Unit identification The unit can be assigned a name and an ID to facilitate identification. Both make the task of managing several units in larger video surveillance systems with VIDOS von VCS or other tools much simpler.
Configuring the Receiver Chapter 7 Password A VIP unit is generally protected by password to prevent unauthorized access. You can limit the scale of access by choosing between different authorization levels (User name:). Note Correct password protection is only granted when all higher levels of authorization are also protected by password. If a user password is assigned a service password must be assigned, too. Therefore assign passwords always beginning with the highest authorization level.
Chapter 7 Configuring the Receiver Note The new password becomes effective only after you have clicked Set. Therefore always click Set immediately after having entered and confirmed the password even if afterwards you want to assign a password to another user name, too. Language Website language: Select the language for the website from the dropdown field. Date and time If a number of units are part of a system, it is important that the internal clocks of these separate units be synchronized.
Configuring the Receiver Chapter 7 Unit date: Enter the current date here. Since the unit time is controlled by the internal clock, it is not necessary to enter the day of week. This is added automatically. Unit time: Enter the current time here or click the Synchr. PC button to copy the system time of your computer to the VIP. Time server Using the Time Server Protocol the VIP can receive a time signal from a time server and use it to set its internal clock.
Chapter 7 Configuring the Receiver MPEG decoder The monitor can be assigned a name to facilitate identification. The video output standard for the connected monitor can also be selected here. The VIP can monitor the incoming data stream for integrity and can display a notification text on the monitor when it has detected disturbances in the transmission. Monitor name: Enter the desired monitor name here. The monitor name is used for easier identification of the monitor in large systems, e.g.
Configuring the Receiver Chapter 7 Disturbance sensitivity level: Here you can define at what level the text display is triggered. The lower the value the higher the sensitivity level of the VIP. Notification text: Enter the text that is to be displayed on the monitor. It can contain up to 31 characters. Audio stream In addition to video data, the unit can also send and receive audio signals. The transmission of audio takes place at the same time as that of the video data in a separate data stream.
Chapter 7 Configuring the Receiver Alarm sources Both VIP decoder alarm inputs can be configured individually. Alarm input 1 ... Alarm input 2: Select the option On in order to activate the alarm via the corresponding external alarm sensor. Otherwise, select Off. Choose Active high to trigger the alarm closing the contact. Choose Active low to trigger the alarm opening the contact. Name: You can enter a name for each alarm input. 1./2.
Configuring the Receiver Chapter 7 Alarm connections You can select a number of options for the response of the VIP to an alarm. In case of an alarm, the VIP can establish a connection to a predefined IP address, e.g. a VIP sender, automatically. You can enter up to ten IP addresses which will be selected in sequence by the unit until a connection is established. Note Sender and receiver must share the same subnet for connection set-up (see page 86).
Chapter 7 Configuring the Receiver Note If the VIP connects to a "dual streaming“ encoder Stream 1 will be transmitted. Number of destination IP address: Here you assign the numbering for the IP addresses to be contacted in the event of an alarm. The unit contacts the remote locations one after the other in the numbered sequence until a connection has been established. Destination IP address: For each number, enter the corresponding IP address of the desired remote unit.
Configuring the Receiver Chapter 7 Relay You can configure the switching behavior of the relay output. Relay action can be specified either as open switch (normally closed contact) or closed switch (normally open contact). It is also possible to specify whether the output signal should be bistable or monostable. With bistable operation, the relay remains in the activated state. With monostable operation, the delay time can be selected after which the relay reverts to its idle state.
Chapter 7 Configuring the Receiver Relay follows: Select a particular event to trigger the relay. The following events can activate the relay: ] Off No relay triggering by events ] Connection Triggering caused whenever a connection is established ] Local input 1 Triggering caused by the alarm input 1 ] Remote input 1 Triggering caused by a relay contact at a remote location (only when a connection is established) Relay name: A name can be assigned to the relay in this field.
Configuring the Receiver Chapter 7 COM1 The RS232/485 serial interface port can be configured to meet your requirements. Serial port function: If you want to use the serial interface to transmit transparent data, select Transparent. To operate the VIP with a terminal, choose Terminal. Note After selecting an interface function, the remaining parameters in the window are set automatically and should not be altered. Camera ID: The camera ID cannot be changed.
Chapter 7 Configuring the Receiver Stop bits: Select the number of stop bits per character. Parity check: Select the type of parity check. Interface mode: Select the desired protocol for the serial interface. Half-duplex mode: Choose the setting appropriate for your application. Network The settings on this page are used to integrate the unit into an existing network. Warning! Changes to the IP address, subnet mask or gateway address are sent to the unit when the Set button is clicked.
Configuring the Receiver Chapter 7 – Enter the old IP address in the address field of the Web browser and append /reset to it (e.g. 192.168.0.2/reset). The VIP will be restarted after which it can only be accessed at the new IP address. Unit IP address: Enter the desired IP address for the VIP in this field. The IP address must be valid for the network. Subnet mask: Enter the subnet mask corresponding to the inserted IP address here.
Chapter 7 Configuring the Receiver Warning! Errors such as picture interference can occur if the network capacity is not suitable for transmission of the maximum data rate generated by the VIP. Dynamic DNS server IP address: When operating a unit over the Internet, an address pool with dynamic addresses is used for greater efficiency. This means that the unit is assigned an IP address each time a connection is made and this address varies.
Configuring the Receiver Chapter 7 Firmware version: The firmware version number of the VIP is displayed. Firmware and configuration upload Firmware update: The VIP is designed in such a way that its functions and parameters can be updated with firmware. To accomplish this, the current firmware is loaded on the unit via the selected network. It will be installed automatically. Thus a VIP unit can be serviced and updated remotely without requiring a technician to make changes on-site.
Chapter 7 Configuring the Receiver The new firmware will be decompressed and used to reprogram the flash EPROM. The time necessary is indicated by the message going to reset Reconnecting in ... seconds. After the upload is completed successfully, the unit will restart automatically. If the „operating status“ LED blinks red and yellow alternately, the upload has failed and must be done again.
Configuring the Receiver Chapter 7 Function test The VIP offers a number of configuration options. Therefore you should check that it works properly after installation and configuration. This is the only way to ensure that the VIP will function as intended in an alarm situation.
Sender Operation 8 Operation with Microsoft Internet Explorer A computer with Microsoft Internet Explorer (version 6.0 or later) can be used to receive live images from the VIP, control cameras or other peripherals and replay sequences stored on the local hard drive. Note Make sure the graphic card is set to 16 or 32 bit color depth and the Microsoft Virtual Machine is installed and active on your computer.
Sender Operation Chapter 8 – Follow the instructions on the screen. Establishing the connection The VIP must be provided with a valid IP address to operate on your network. The following default address has been pre-set at the factory: 192.168.0.1 – Start the Web browser. – Enter the IP address of the VIP as the URL. The connection will be established, and after a short time the Livepage with the video image will appear.
Chapter 8 Sender Operation Other information may also be shown next to the video image on the Livepage. The display depends on the settings on the configuration page Livepage configuration (see page 67). Note If the connection is not established, the maximum number of possible connections may already have been reached. The maximum number of connections depends on the unit and network configuration.
Sender Operation Chapter 8 Relay output Depending upon configuration, a device such as a floodlight or a door opener can be activated by the relay of the VIP unit. The display of the relay and other details depends on the configuration of the unit (see page 58). – Click the relay symbol next to the video image to activate the relay output. The symbol will turn red when the relay is activated. Event log The Event log field is where events such as switching a relay or alarm status messages are listed.
Chapter 8 Sender Operation If a controllable device is connected to the VIP and configured, the controls for the peripheral are displayed next to the video image, here e.g. for a Sony EVID30/31. – To control a peripheral device click the associated operating elements. – Move the pointer over the video image. Further options for peripheral device control will be displayed using the pointer.
Sender Operation Chapter 8 Panorama view If you are working with a Sony EVI-D100 or EVI-D30/31 camera, you can also display a panoramic image. The panoramic image is shown in the upper part of the Livepage. It consists of five single images that can be updated any time. – Right-click on the panoramic image to open the context menu. – Select Start scan to update the individual images. Stop scan cancels the update.
Chapter 8 Sender Operation Saving snapshots Individual images from the current video sequence on the Livepage can be saved on the computer hard drive in JPEG format. – Click the Snapshot icon. The image will be saved. The storage location depends on the configuration of the VIP (see page 70). Image resolution Snapshots can be called up and displayed at different resolutions by entering URL parameters in the address field of the Web browser: – Type the IP address of the VIP, followed by /snap.
Sender Operation Chapter 8 Recording video sequences Segments from the current video sequence on the Livepage can be saved on the computer hard drive. Click the MPEG-sequence icon. Saving begins immediately. The storage location depends on the configuration of the VIP (see page 70). A recording in progress is indicated by the blinking of the red dot on the icon. – Click the MPEG-sequence icon again. Saving will be terminated.
Receiver Operation 9 Operation with Microsoft Internet Explorer A computer with Microsoft Internet Explorer (version 6.0 or later) can be used to set up a connection to a VCS sender and to display the live images received on a monitor. Note Make sure the graphic card is set to 16 or 32 bit color depth and the Microsoft Virtual Machine is installed and active on your computer.
Receiver Operation Chapter 9 – Follow the instructions on the screen. Establishing the connection The VIP must be provided with a valid IP address to operate on your network. The following default address has been pre-set at the factory: 192.168.0.2 – Start the Web browser. – Enter the IP address of the VIP as the URL. The connection will be established, and after a short time the Decoder connection page will appear.
Chapter 9 Receiver Operation VIP password protection If the VIP is password-protected against unauthorized access, a corresponding message and a prompt to enter the password will appear first. Note A VIP provides various authorisation levels to limit the scope of a user's access (see page 74). – Enter the user name and the associated password in the appropriate fields. – Click OK. If the password is is correct the respective page is displayed.
Receiver Operation Chapter 9 – Mark the checkbox Include audio if you want to transmit audio, too. Make sure for correct audio transmission configuration for both, sender and receiver. – Mark the checkbox Include data if you want to transmit transparent data, too. Make sure for correct data transmission configuration for both, sender and receiver. Note The checkboxes must be marked prior to connection set-up in order to include audio and data transmission.
Hardware Connections 10 Hardware connections between VCS units A VIP sender, connected to a camera, and a VIP receiver, connected to a monitor, can be linked together or to other VCS units easily via an Ethernet network. This makes it possible to establish connections over large distances with little effort for installation or cabling. Installation The VCS units are designed to connect with one another automatically when correspondingly configured.
Hardware Connections Chapter 10 Connection when an alarm signal is given Sender and receiver can be configured to connect automatically with each other when an alarm is triggered (see page 53 for sender and page 81for receiver). After a short time, the live video image from the sender will be shown on the connected monitor. This option can also be used to connect two VCS units via an on-off switch at the receiver. In this case, a computer is not needed to establish the connection (see page 80).
Chapter 10 Hardware Connections Closing the connection The connection may be closed using a terminal program or Web browser. Closing the connection using a terminal program – Start the terminal program (see page 23); enter the command i to call up the IP menu. – Enter the command a in the IP menu to deactivate automatic connection. Closing the connection using a Web browser – Use the Web browser to connect to the VIP receiver. Its home page will be displayed.
VIP 1000
Operation with Decoder Software 11 Operation with VIDOS VIP video servers and VIDOS software can be combined to form a highperformance system solution. VIDOS is software for the operation, control and administration of CCTV installations (e.g. surveillance systems) at remote locations. It runs under Microsoft Windows operating systems. Its main function is decoding video, audio and control data from a remote sender.
VIP 1000
Maintenance and Upgrades 12 Testing the network connection The ping command can be used to check the connection between two IP addresses. This allows you to test whether a unit is active in the network. – Open the DOS command prompt. – Type ping followed by the IP address of the unit. If the unit is found, the response appears as Reply from ..., followed by the number of bytes sent and the transmission time in milliseconds. Any other response indicates that the unit cannot be accessed via the network.
Maintenance and Upgrades Chapter 12 – If necessary, back up the current settings using the Download button on the configuration page entitled Firmware and configuration upload (see page 70 for sender and page 88 for receiver). – Use a pointed object to press the reset button which is found below the USB interface (see page 16) until the „operating status“ LED blinks red. All settings will revert to their defaults. – Change the IP address of the unit as necessary.
13 Appendix Troubleshooting If you cannot correct a malfunction, please contact your supplier, system integrator or VCS customer service (Support.STVC@de.bosch.com). The version numbers of the internal processors can be viewed on a special page. Please note this information before contacting Customer Service. – In the address field of the browser, append /version.htm to the IP address of the unit (e.g. 192.168.0.12/version.htm) and press Enter. – Write down the information or print out the page.
Appendix Chapter 13 Problem Possible Causes Solution No connection established, no image transmission. The unit's configuration. Check all settings. Faulty installation. Check all cables, plugs, contacts and connections. Wrong IP address. Check the IP addresses (terminal program). Faulty data transmission within the LAN. Check data transmission with the ping command. The maximum number of connections possible to other devices has already been reached.
Chapter 13 Appendix LEDs The VIP video server is equipped with several LEDs that show the operating status and can give indications of possible malfunctions: Operating status LED Not lit: Device is switched off. Lit yellow: Device is switched on. Lit red (briefly): Device is starting up. Lit red (continuously): Device is out of order. Blinking yellow/red: Upload failed. Network connection LED Lit green: Connected to the network. Not lit: Not connected to the network.
Appendix Chapter 13 RS232/485 interface Options for using the serial interface include transparent data transfer, control of connected devices or operation of the unit with a terminal program. Depending on the setting, the interface works with the RS232 or RS422/485 standard. The standard used depends on the current configuration (see page 60). Depending on the device the serial interface is either a Sub-D connector (receiver) or an RJ45 connector (sender).
Chapter 13 Appendix RJ45 connector pin assignments (sender) The pin assignments depend on the standard used.
Appendix Chapter 13 Connection jacks The connection jacks are used to connect to the mains supply. As standard, the connection to the power supply unit is made here. They also allow the connection of alarm switches, relays, an audio source and a loudspeaker.
Chapter 13 Appendix Glossary A few brief explanations of the most important terms and abbreviations used in the field of communications technology can be found below. 10/100 Base-T IEEE 802.
Appendix Chapter 13 MAC Media Access Control MPEG-2 Enhanced video compression standard, with high-level compression that makes images of studio quality possible. It has now become established as a broadcasting standard. MPEG-4 Further development of MPEG-2, designed for transmission of audiovisual data at very low transfer rates (for example via the Internet). MTU Maximum Transmission Unit resp.
Chapter 13 Appendix VIP 1000 Specifications Operating voltage 12 ... 24 V DC, power supply included Power consumption approx. 10 W Network interface Ethernet 10/100 Base-T, auto-sensing, half/fullduplex, RJ45 Video data rate 1 MBit/s ... 8 MBit/s (MPEG-2) 9.6 kBit/s ...
Appendix Chapter 13 1 × USB 1.1 Alarm input 2 × push-in terminal, max. activation resistance 10 Ohm Relay output 1 × push-in terminal, 30 Vpp, 1 A Indicators 3 LEDs (operating status, network connection, data transfer) Operating conditions Temperature 0 ... +50°C, relative humidity 20 ... 80%, non-precipitating Approvals & certifications CE; IEC 60950; UL 1950; AS/NZS 3548; EN 55103-1, -2; EN 55130-4; EN 55022; EN 55024; EN 61000-3-2; EN 61000-3-3; FCC 47 CFR Ch.
14 Index A Conventions 7 Active profile 46 Actuator 21 D Alarm 80 Data interface 20 Alarm input 21 Data rate 47 Alarm inputs 93 Data terminal 23 Alarm IP address 54 Date format 37, 75 Application Wizard 31 Daylight savings time 38, 76 Audio connection 21 Defaults 48 Audio signals 48, 78 Display stamping 39 Auto-connect 54, 81 DNS server 63, 87 Dome camera 20 B Banner 67, 68 Dual Streaming 45 Dual streaming 13 Brightness 41 Browser window 92 E C Electromagnetic compatibility 8 Echo
Index G Gateway 62, 86 GOP 43 I Identification 8, 35, 73 IGMP 64 Image resolution 97, 98 Installation 10 Installation location 19 Installation requirements 19 Installation Wizard 31 Interlaced video signal 48 Internal clock 38, 76 IP address 24, 62, 86 J JPEG format 50 JPEG posting 50 JPEG posting interval 51 L Language 37, 75 Chapter 14 Monitor name 77 Monitor resolution 91, 99 Motion alarm 52 MPEG ActiveX 98 MPEG-ActiveX 27, 91, 99 MPEG-sequence 98 MTU 62, 86 Multicast 64 Multicast connection 62, 64, 8
Chapter 14 Index R U Receiver 13 UDP 62, 86 Regulations 7 Unicast 64 Relay 58, 82, 94 Unit name 35, 73 Relay output 21, 58, 82, 94 Update 70, 88 Remote control 14 Upload file 70, 88 Repair 10 URL 28, 92, 100 Restart 25 User name 36, 74 Router 66 V S Version 66, 87 Safety 9 Video loss alarm 52 Save picture 97 Video output standard 77 Setup 11 Video quality 47 SNMP 52, 79 Video resolution 48 Specifications 119 Video sensor 54 Subnet mask 86 Video sequence 98 Symbols 7 Synchro
Index Chapter 14 124 VIP 1000
VIP 1000 125
VCS Video Communication Systems AG Forchheimer Str. 4 90425 Nuremberg, Germany Phone: +49 911 93456-0 Fax: +49 911 93456-66 E-mail: info@vcs.com http://www.vcs.com ID No.
