Installation Sheet

ManualsBrandsVaxcel ManualsOutdoor Wall SconcesVaxcel Lighting Bridgeport Single Light 15" Tall Outdoor Wall Sconce with A Glass Shade

Page 1/4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

T0456

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

Features

1. Energy saving fixture.

2. Use the dim-to-bright illumination option where

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

181213

Important to Know

1. Read all instructions carefully before installation and operation.

2. If you are not familiar with state and local electrical codes, it is

recommended that you consult with a qualified electrician.

3. Before installation, shut off power at the main fuse or circuit

breaker box. Be aware that simply turning off the wall switch is

not sufficient to prevent an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge, make

sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to the

sensor, be sure the power is switched "off" before replacing the

bulb.

8. Compatible with LED dimmable bulb.

Maximum Wattage: 60W

Incandescent Bulb or 20W LED

Dimmable Bulb

Work Temperature: -4°F~104°F

Hardware Package (included)

Lock Nut (E) Rubber

Pad (H)

Wire Connector (F)

Ball Nut (G)

Headless

screw (D)

Green Grounding

Screw (C)

Mounting Screw (B)

Mounting plate (A)

House Grounding Wire

Fixture Grounding Wire

Wire Connector (F)

Mounting Plate (A)

Outlet Box

Fixture

Wire

Lock Nut (E)

Headless Screw (D)

Mounting Screw (B)

Green Grounding Screw (C)

Ball Nut (G)

Fixture

Rubber Pad (H)

Socket

Socket Ring

Glass Shade

Vintage Bulb Max.60W

or Max.20W

Dimmable LED

Bulb (not included)

Summary of content (4 pages)

PAGE 1
T0456 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Features Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation steps Turn off the power at fuse or circuit box. 1. Thread two headless screws (D) through the mounting plate (A), and then secure them with four lock nuts (E) (two on each side of the mounting plate (A).) Adjust the length of the headless screws (D) if necessary. Note: Make sure the headless screws are lined up horizontally to make the fixture level. 2. Attach the mounting plate (A) to the outlet box by using two mounting screws (B). 3. Pull out the source wires from the outlet box.
PAGE 3
5. Manual Override MODE (nighttime operation only; on at dusk,off at dawn) ● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again, the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous settings, turn off the wall switch in 3 seconds and then turn it on again. (See Fig.1 Fig.2) ● The lights will turn off automatically at dawn. FIG.
PAGE 4
----In Test Mode, the light stays on full brightness after 5 seconds: 1. If during daytime, make sure the slide switch is at the TEST position. 2. Whether the motion is detected at all time. ---In 3H or 6H Mode, the light is still on full brightness,even though it has been 3 hours or 6 hours after dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override.