Installation Sheet

ManualsBrandsVaxcel ManualsOutdoor Wall SconcesVaxcel Lighting Franklin Single Light 14" Tall Outdoor Wall Sconce with A Metal Shade

Page 1/4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

T0385

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

Features

1. Energy saving fixture.

2. Use the dim-to-bright illumination option where

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

180928

Mounting Screw (B)

Green Grounding

Screw (C)

Lock Nut (E)

Wire Connector (F)

Ball Nut (G)

Rubber Pad (H)

Cross Bar (A)

Important to Know

1. Read all instructions carefully before installation and operation.

2. If you are not familiar with state and local electrical codes, it is

recommended that you consult with a qualified electrician.

3. Before installation, shut off power at the main fuse or circuit

breaker box. Be aware that simply turning off the wall switch is

not sufficient to prevent an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge, make

sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to the

sensor, be sure the power is switched "off" before replacing the

bulb.

8. Compatible with LED dimmable bulb.

Maximum Wattage: 60W Incandescent Bulb or 20W LED

dimmable bulb.

Work Temperature: -4°F~104°F

Hardware Package (included):

Green Grounding Screw (C)

Outlet Box

Wire Connector

(F)

Headless Screw (D)

Cross Bar (A)

Lock Nut

(E)

House Grounding Wire

Fixture Grounding Wire

Bulb Type A Max.60W or

20W LED dimmable bulb

(not included)

Mounting Screw (B)

Fixture

Back Plate

Ball Nut(G)

Rubber Pad(H)

Headless

Screw (D)

Fixture Wire

Summary of content (4 pages)

PAGE 1
T0385 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Features Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation steps Turn off the power at fuse or circuit box. 1. Thread two fixture mounting screws through the cross bar, and then secure them with four lock nuts（ two on each side of the cross bar）.Adjust the length of the fixture mounting screws if necessary. Note: Make sure that the fixture mounting screws are lined up horizontally to make the fixture level. 2. Attach the cross bar to the outlet box by using two mounting screws. 3. Pull out the source wires from the outlet box.
PAGE 3
Fig.1 Fig.2 Manual Override Operation Diagram AUTO Mode Turn wall switch OFF-ON in 3 Seconds Turn wall switch OFF-ON in 3 Seconds again On the back of the sensor Time Low Level Sens Manual Override Mode Test 3H 6H 0 CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected.
PAGE 4
---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours after dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override. ---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes: 1. Make sure there is no movement that could be picked up by the sensor. 2. Adjust the time knob counterclockwise to reduce the delay shut-off time.