Installation Guide (P0324)

ManualsBrandsVaxcel ManualsShop All VaxcelVaxcel Lighting Milano Single Light 6" Wide Pendant

191205

1. Unscrew two ball nuts (H), remove mounting strap (A) from canopy.

2. Loosen the plastic headless screw on the canopy by using flathead

screw driver (I) .

3. Thread the cord through the canopy and strain relief (G). Measure the

desired length of the cord (a) from the canopy to the glass shade and

leave additional 9" cord (b) above the canopy (include the canopy),

and then cut off the unnecessary cord. (See Fig.1)

4. Adjust strain relief (G) at 9" position from the top of the cord.

5. Mark the 3" cord (c) from the top of the cord (b). Use a knife

to peel off the insulation of the cord (c) carefully to show the

3 inside wires out. (See Fig. 1)

Caution : Cutting too deep may cut off three inside wires

and destroy the insulation surface of the three inside wires.

6. Peel off the 3 wires from the top about 3/8" long (d) to expose

the copper for wiring.

7. Attach the mounting strap

(A)

to outlet box by using two mounting

screws

(B)

8. Pull out the source wires from the outlet box. Make wire connections

using wire connectors

(F)

as follows:

a. Connect the hot wire marked "L" from the fixture to the black wire

from the power source.

b. Connect the neutral wire marked "N" from the fixture to the white wire

from the power source.

c. Connect the copper wire or green wire marked " " from the fixture

to the mounting strap (A) by securing it with the green ground screw.

The green ground wire marked " " from the fixture to the green

ground wire from power source.

Carefully put wires back into the outlet box.

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THIS INSTRUCTION.

P0324

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.

Hardware Package (included):

Turn off the power at fuse or circuit box.

Fig.1

Installation Steps

Canopy

Ball Nut (H)

Cord (a)

Fixture Wire

Hex Nut

Strain Relief (G)

Mounting Strap (A)

Green Ground Screw (C)

Lock Nut (D)

Mounting Screw (B)

Wire Connector (F)

Fixture Mounting Screw (E)

Outlet Box

c(3")

d(3/8")

b(9")

Plastic Headless

Screw

Mounting Screw (B)

Wire Connector (F)

Strain Relief (G)

Mounting Strap (A)

Fixture Mounting Screw (E)

Green Ground Screw (C)

Lock Nut (D)

Ball Nut (H)

Flat Head Screwdriver (I)

Glass Shade

Fixture

Socket

Socket Ring

Medium Base Bulb

Max.60W (not included)

Summary of content (2 pages)

PAGE 1
P0324 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THIS INSTRUCTION.
PAGE 2
9. Pull the cord (a) down slightly until the strain relief (G) touches the hex nut. Attach two fixture mounting screws (E) to the mounting strap (A), then secure it with two lock nuts (D). Adjust the length of the fixture mounting screws (E) if necessary, then secure it with two ball nuts (H). 10. Fastening cord by screwing plastic headless screw, using flat head screwdriver (I). 11. Attach the glass shade to fixture, then secure it with the socket ring. 12. Install a bulb (not included).