Installation Sheet

ManualsBrandsVaxcel ManualsShop All VaxcelVaxcel Lighting Milano Single Light 5" Wide Pendant with A Glass Shade

181017

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THIS INSTRUCTION.

P0276 / P0278

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.

Hardware Package (included):

Turn off the power at fuse or circuit box.

Fig.1

Installation Steps

Mounting Screw (B)

Wire Connector (F)

Strain Relief(G)

Fixture

Glass Shade

Socket

Mounting Strap (A)

Fixture Mounting

Screw (E)

Green Grounding

Screw (C)

Canopy

Ball Nut(H)

Cord(A)

Fixture Wire

Hex Nut

Socket Ring

Lock Nut (D)

Ball Nut (H)

Bulb Type A Max.60W

(not included)

Strain Relief (G)

Mounting Strap (A)

Lock Nut (D)

Mounting Screw (B)

Green Grounding Screw (C)

Wire Connector (F)

Fixture Mounting Screw(E)

Outlet Box

D(3/8")

B(9")

Plastic

Headless

Screw

1. Unscrew two ball nuts, remove mounting strap from canopy.

2. Loosen the plastic headless screw on the canopy by using a

flathead screw driver (not included), .

3. Thread the cord through the canopy and strain relief. Measure the

desired length of the cord (A) from the canopy to the glass shade and

leave additional 9" cord (B) above the canopy(include the canopy),

and then cut off the unnecessary cord.(See Fig.1)

4. Adjust strain relief at 9" position from the top of the cord.

5. Mark the 3" cord (C) from the top of the cord (B). Use a knife to peel

off the insulation of the cord (C) carefully to show the 3 inside wires

out. (See Fig. 1)

Caution : Cutting too deep may cut off three inside wires and

destroy the insulation surface of the three inside wires.

6. Peel off the 3 wires from the top about 3/8" long(D) to expose the

copper for wiring.

7. Attach the mounting strap to outlet box by using two mounting screws.

8. Carefully inspect the fixture wires, the NEUTRAL wire (with a white line

along its length), the HOT wire (clear), the GROUND wire (with a green

line along its length) before making wire connections.

9. Pull out the source wires from the outlet box. Make wire connections

using wire connectors as follows:

a. The hot wire marked "L" from the fixture to the black wire from the power source.

b. The neutral wire marked "N" from the fixture to the white wire from the power source.

c. The green grounding wire marked " " from the fixture to the green grounding wire from power source.

Carefully put wires back into the outlet box.

C(3")

Summary of content (2 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS P0276 / P0278 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THIS INSTRUCTION.
PAGE 2
10. Pull the cord (A) down slightly until the strain relief touches the hex nut. Attach the canopy to the mounting strap by inserting two fixture mounting screws, and then secure it with two ball nuts. 11. Fastening cord by screwing plastic headless screw, using flat head screw driver (not included). 12. Attach the glass shade to fixture, and then secure it with the socket ring. 13. Install a bulb (not included). Check relamping label at socket area or packaging for maximum allowed wattage.