Installation Sheet

ManualsBrandsVaxcel Lighting ManualsLightingNottingham 2 Light 17" Tall Outdoor Wall Sconce

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

T0597

Important to Know

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical codes,

it is recommended that you consult with a qualified

electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off the

wall switch is not sufficient to prevent an electrical shock.

4. This fixture requires a 120V AC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge,

make sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to

the sensor, be sure the power is switched "off" before

replacing the bulb.

Maximum Wattage: 2~25W Incandescen Bulb

Work Temperature: -4ºF ~ 104ºF

Hardware Package (included):

Mounting Screw (B) Wire Connector (C)

Bolt Nut (D) Rubber Pad (E)

Mounting Plate Unit (A)

Max. 25W type B Bulb

(not included)

WARNING: Turn off the main power at circuit breaker before installing fixture.

AVERTISSEMENT: Coupez la source d’alimentation principale au panneau

central de disjoncteurs avant d’installer le luminaire.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ

AND SAVE THESE INSTRUCTIONS.

Page 1 / 5

Glass Panel

Metal Frame

Clip

Fixture

Backplate

Wire Connector (C)

House Grounding Wire

Outlet Box

Mounting Screw (B)

Green Grounding Screw

Headless Screw

Mounting Plate Unit (A)

Fixture Wire

Rubber Pad (E)

Ball Nut (D)

Fixture Grounding Wire

Set Screw

8. Compatible with most LED dimmable bulb.

Features

1. Energy saving fixture.

2. Use dim-to-full brightness where dim-illumination

is preferred, such as your front entrance. Use

off-to-full brightness where off/on illumination is

preferred, such as your backyard.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

210317

Summary of content (5 pages)

PAGE 1
T0597 W ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: Turn off the main power at circuit breaker before installing fixture. AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Features Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation Steps Turn off the power at fuse or circuit box. 1. Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate. 2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary. Note: Make sure that two headless screws are lined up horizontally to make the fixture level. 3. Loosen the two set screws to remove metal frame from fixture. 4.
PAGE 3
Function and Operation MODES OF OPERATION Choose a mode by sliding the switch on the back of the sensor. When power is first applied, the light will turn on immediately. Wait for 100 seconds to allow the sensor to warm up. 1. TEST MODE (daytime and nighttime operation) ● The light will turn to low-level brightness (0%~50% brightness). The light will turn to high-level brightness (100% brightness) when motion is detected, and stay on as long as the motion is continuing.
PAGE 4
NOTE: 1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to assure maximum sensitivity. 2. For best performance, install fixture at least 6 feet above the ground. At such a height, the fixture will provide a detection distance of up to 40 feet at 77 degrees fahrenheit. (See Fig.6) 3. The sensor detects across a detection range of 180 degrees (See Fig.7) 4.
PAGE 5
The following parts are available for re-order if damaged or missing.