Installation Guide

ManualsBrandsVaxcel Lighting ManualsLightingGlenn Single Light 13" Tall Outdoor Wall Sconce

Page 1/4

Features

1. Energy saving fixture.

2. Use the dim-to-bright illumination option where

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

191217

Important to Know

1. Read all instructions carefully before installation and operation.

2. If you are not familiar with state and local electrical codes, it is

recommended that you consult with a qualified electrician.

3. Before installation, shut off power at the main fuse or circuit

breaker box. Be aware that simply turning off the wall switch is

not sufficient to prevent an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge, make

sure the grounding wire is securely connected.

7. For general safety and to avoid any possible damage to the

sensor, be sure the power is switched "off" before replacing the

bulb.

8. Compatible with LED dimmable bulb.

Maximum Wattage: 60W

Incandescent Bulb or 20W LED

Dimmable Bulb

Work Temperature: -4°F~104°F

Hardware Package (included)

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

T0569

WARNING: Turn off the main power at circuit breaker before installing fixture.

AVERTISSEMENT: Coupez la source d’alimentation principale au panneau

central de disjoncteurs avant d’installer le luminaire.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ

AND SAVE THESE INSTRUCTIONS.

Backplate

Bulb (not included)

Max.60W Type Vintage

Wire Connector (C)

House Grounding Wire

Outlet Box

Mounting Screw (B)

Green Grounding Screw

Headless Screw

Mounting Plate Unit (A)

Fixture Wire

Fixture Grounding Wire

Bolt Nut (D)

Rubber Pad (E)

Set Screw x 3

Glass Shade

Mounting Screw (B) Wire Connector (C)

Ball Nut (D) Rubber Pad (E)

Mounting Plate Unit (A)

Fixture

Socket

Summary of content (4 pages)

PAGE 1
T0569 ASSEMBLY AND INSTALLATION INSTRUCTIONS W WARNING: Turn off the main power at circuit breaker before installing fixture. AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Features Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation Steps Turn off the power at fuse or circuit box. 1. Remove the two bolt nuts (D), the two rubber pads (E) and the mounting plate unit (A) from the backplate. 2. Attach the mounting plate unit (A) to the outlet box using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally to make the fixture level. 3. Pull out the source wires from the outlet box.
PAGE 3
4. 0 MODE (nighttime operation only) ● The light will turn to low level brightness (0%~50% brightness) at dusk. The light will turn to high-level brightness (100% brightness) when motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light will remain on for the predetermined time you set (5~180 seconds), and then revert to low level brightness you set. ● Light will turn off automatically at dawn, and return to 0 H mode at dusk. 5.
PAGE 4
----In Test Mode, the light stays on full brightness after 5 seconds: 1. If during daytime, make sure the slide switch is at the TEST position. 2. Whether the motion is detected at all time. ---In 3H or 6H Mode, the light is still on full brightness,even though it has been 3 hours or 6 hours after dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override.