Installation Guide

ManualsBrandsVaxcel Lighting ManualsLightingBartlett 4 Light 24" Wide Pendant

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

P0328

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.

Hardware Package (included):

Green Ground Screw (E)

Fixture Mounting Screw (D)Mounting plate (A)

Bolt Nut (G)

Mounting Screw (B)

Lock Nut (F)

Wire Connector (C)

Turn off the power at fuse or circuit box

Installation Steps

1. Thread two fixture mounting screws (D) through the mounting plate (A),

then secure them with two lock nuts (F) (two on each side of the

mounting plate (A).) Adjust the length of the fixture mounting screws

(D) if necessary.

Note: Make sure the fixture mounting screw are lined up horizontally

to make the fixture level.

2. Attach the mounting plate (A) to the outlet box by using two

mounting screws (B).

3. Rod connections:

a. Thread the fixture wire from the fixture through the lower rod,

then secure the lower rod onto the fixture using the threaded pipe.

b. Thread the fixture wire through the middle rod, then secure the

middle rod onto the lower rod using the threaded pipe.

c. Thread the fixture wire through the upper rod, then secure the

upper rod onto the middle rod using the threaded pipe.

The height can be adjustable to 28-1/2" ~ 85-1/2", by using

the rods.

4. Thread the fixture wire through the canopy, then secure the

rod assembly to the set threaded pipe of the canopy.

5. Pull out the source wires from the outlet box.

Make wire connections using wire connectors (C) as

follows:

---Connect the hot wire (black insulation) from the

fixture to the black wire from the power source.

---Connect the neutral wire (white insulation) from the

fixture to the white wire from the power source.

---Attach the fixture ground wire (bare wire) to the

mounting plate (A) with the green ground screw (E),

then connect it to the house ground wire with the

wire connector (C).

Carefully put the wires back into the outlet box.

191106

House Ground Wire

Fixture Ground Wire

Fixture Mounting Screw (D)

Wire Connector (C)

Mounting Plate (A)

Green Ground Screw (E)

Mounting Screw (B)

Lock Nut (F)

Canopy

Bolt Nut (G)

Outlet Box

Set Threaded Pipe

Fixture Wire

Upper Rod

Middle Rod

Lower Rod

Threaded Pipe

Fixture

Medium Base Bulb Max.60W

(not included)

Summary of content (2 pages)

PAGE 1
P0328 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO TO SHUT SHUT OFF OFF TOAVOID AVOID RISK RISK OF OF ELECTRICAL ELECTRICAL SHOCK, BE SURE TO POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
PAGE 2
6. Attach the canopy to the mounting plate (A) by inserting the fixture mounting screws (D), secure it with two bolt nuts (G). 7. Install bulbs (not included). See relamping label at socket area or packaging for maximum wattage allowed. 8. Angled mounting recommended for a vaulted or angled ceiling. (See Fig. 1) Fig. 1 Support Brace Turn on the power at fuse or circuit box Outlet Box Canopy Coupling Kit The following parts are available for re-order if damaged or missing.