Installation Sheet

ManualsBrandsVaxcel Lighting ManualsLightingMilano 1 Light Mini Pendant with Multi-Colored Glass Shade

151102

1. Unscrew two ball nuts, remove mounting strap from canopy.

2. Loosen the plastic headless screw on the canopy using a

flathead screwdriver (not included), .

3. Thread the cord through the canopy and Strain Relief. Measure the

desired length of the cord (A) from the canopy to the glass shade and

Leave additional 9" cord (B) above the canopy(include the canopy),

and then cut off the unnecessary cord.(See Fig.1)

4. Adjust strain relief at 9" position from the top of the cord.

5. Mark the 3" cord (C) from the top of the cord (B). Use a knife to peel

off the insulation of the cord (C) carefully to show the 3 inside wires

out. (See Fig. 1)

Caution : Cutting too deep may cut off three inside wires and

destroy the insulation surface of the three inside wires.

6. Peel off the 3 wires from the top about 3/8" long(D) to expose the

copper for wiring.

7. Attach the mounting strap to outlet box by using two mounting screws.

8. Pull out the source wires from the outlet box. Make wire connections

using wire nuts as follows:

a. The black wire marked "L" from the fixture to the black wire from the

power source.

b. The white wire marked "N" from the fixture to the white wire from the

power source.

c. The green grounding wire marked " " from the fixture to the green grounding wire from power source.

Carefully put wires back into the outlet box.

9. Pull the cord (A) down slightly until the strain relief touches the hex nut. Attach the canopy to the mounting strap by

inserting two screws, and then secure it with two ball nuts.

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THIS INSTRUCTION.

P0171 / P0173 / P0175 / P0177

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.

Hardware Package (included):

Turn off the power at fuse or circuit box.

Installation Steps

Mounting Screw (B)

Wire Nut (F)

Strain Relief(G)

Fixture

Glass Shade

Socket

Mounting Strap (A)

Screw (E)

Green Grounding

Screw (C)

Canopy

Ball Nut(H)

Cord(A)

Fixture Wire

Hex Nut

Socket Ring

Lock Nut (D)

Ball Nut (H)

Bulb Type A Max.60W

(not included)

Strain Relief (G)

Mounting Strap (A)

Lock Nut (D)

Mounting Screw (B)

Green Grounding Screw (C)

Wire Nut (F)

Screw(E)

Outlet Box

C(3")

D(3/8")

B(9")

FIG.1

Plastic

Headless

Screw

Summary of content (2 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS P0171 / P0173 / P0175 / P0177 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THIS INSTRUCTION.
PAGE 2
10. Fastening cord by screwing plastic headless screw, using flat head screwdriver (not included). 11. Attach the glass shade to fixture, and then secure it with the socket ring. 12. Install bulb(not included). Check relamping label at socket area or packaging for maximum allowed wattage. Turn on the power at fuse or circuit box. The following parts are available for re-order if damaged or missing.